The Kerala Agro Industries Corporation Limited Tender

Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1cement :6 coarse sand) etc complete(cement brand: Ultratech, Malabar, Dalmia)

Plastering with cement mortar 1:4, 12mm thick for inside wall, including cost and conveyance of all materials, labour charges, scaffolding, curing etc complete.(Note : Cement brand:- coramandel, ultratech, malabar, dalmia)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1.5:3 ( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)(cement brand: Ultratech, Malabar, Dalmia)

Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Steel work in built up G I tubular round, square or rectangular hollow tubes etc.(Apollo, JSW, Bhushan) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing thermal insulation with Resin Bonded Fibre glass wool conforming to IS : 8183 having density 24 kg/m3, 50 mm thick, wrapped in 200 G Virgin Polythene Bags fixed to wall with screw, rawel plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-in-Charge

Providing and fixing in wall lining medium density fibre board IS: 14587: 1998 marked, Pre-laminated one side decorative lamination and other side balancing lamination, with necessary fixing arrangement and screws etc. complete.18mm thick.

Finishing with Epoxy paint (two or more coats) (Nerolac, Berger. Asian)at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters 0.80x0.90 mm M.S. laths with 0.90 mm thick to cover

Supplying and installing second hand or repurposed shipping containers of standard size 20'x8'x8' which are to be converted into ecoshops with suitable modifications as per the details given in the drawings, including necessary charges for loading,unloading and freight etc and also other modifications like cutting, ventilation, cost and conveyance of the container including necessary billing by authorised department regarding purchase and quality of the container, fixing the container to suitable locations as desired by the client department and all other labour charges etc.,complete. With age of container not more than 12 years and the container being in good condition and confirming to all international and national standards. All relevant documents related to the container to be delivered. The rate also inluding all the loading and unloading charges at KAMCO, the proposed location of the container to be installed anywhere in Kerala and wherever required as per the direction of Engineer - in - Charge.

Providing and laying vitrified floor tiles(Kajaria, Asian, Jhonson) in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on quick set adhesive), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

Providing & fixing Poly carbonate multi wall plain sheet 4 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/ self tapping screw of size (5.5x55mm) with EPDM seal complete upto any pitch in horizontal / vertical / curved surfaces, but excluding the cost of purlins, rafters, trusses and including cutting to size and shapes where ever required.

Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

Providing and fixing Frosted glass sheet of nominal thickness 4mm (weighing not less than 10kg/sqm)

Providing and fixing multipurpose cement board(High pressure steam cured) as per IS: 14862, with suitable screws for fibre cement board in ceiling, flooring etc. complete (frame work to be paid separately): 8mm thick cement bonded wood particle board as per IS: 14276

Providing corrugate G.S. sheet roofing (Apollo, JSW, Bhushan) including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.50 mm thick with zinc coating not less than 275 gm/m2

Providing ridges or hips width 60 cm overall width plain G.S. sheet (Apollo, JSW, Bhushan)fixed with polymer coated J or L hooks, bolts and nuts 8 mm dia G.I. limpet and bitumen washers complete.0.50 mm thick with zinc coating not less than 275 gm/m2

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required:Kitchen sink without drain board470x420 mm bowl depth 178 mm

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of 300 litres capacity :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10 Kgf/cm2- External work - Exposed on wall

Providing and fixing PVC pipes including fixing the pipe with clamps/ clip at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 63 mm dia 6 Kgf/cm2 - External work - Exposed on wall

Electrification: The contractor has to quote a lumpsum amount for electrification, such as providing 300mm dia exhaust fan(crompton), 600mm dia wall fan(crompton), 4Nos of 200mm dia 20W LED ceiling light, necessary switches, plugs, socket, cables etc.