Steel Industrials Kerala Limited Tender

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.22.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

10.1 Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

50.10.2 Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

10.26.3 Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approves steel primer.G.I. pipes

13.61.1 Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

50.12.2.1 Providing & fixing Poly carbonate corrugated sheet 0.8 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12 M or as decide by the Engineer in charge. The sheets shall be fixed using self drilling / self tapping screw of size (5.5x55 mm) with EPDM seal complete upto any pitch in horizontal/ vertical/ curved surface, but excluding the cost of purlins, rafters, trusses, and including cutting to size shapes where ever required.

od161841/2023_2024 od256476/2021_2022 :Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch ofbrcorrugation as approved by Engineer-in-charge) 0.450 mm ( TATA Make ) (+0.05%), total coated thicknessbrwith zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer onbrboth side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25brmicrons minimum to avoid scratches during transportation and should be supplied in single length upto 12brmetre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws ofbrsize (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces,brexcluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.brDetails of cost for 216.14 sqm

od206477/2023_2024 Providing and fixing of Chequered Wooden plywood (Western plywoods, WIPCHECK ) 12 mm thick, conformingbrto IS: IS:303 - 1989, for plain lining / cladding with necessary screws, includingbrpriming coat on unexposed surface with :brDecorative veneer facings of approved manufacture

od161843/2023_2024 Providing and fixing Granite of any colour & shade for Name Board of required size laid over base of cement mortar 1:4(1 cement : 4 coarse sand), including all charges etc, complete at all levels, including lettering & fixing.