Sports Kerala Foundation Tender

od166349/2023_2024 : Triple Twister - Supply and Installation of Triple Twister (Standing position - 2 and Seating position - 1) having the following specifications: Dimensions: (L X W X H) 1500 x 1500 x 1420 mm. Main frame – Ø 114 mm OD “B” class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Seat plate support – Ø 60 mm OD “B” Class G.I Pipe. Seating ring - Ø 33 mm OD “B” Class G.I Pipe made by rolling. Seating ring support - Ø 33 mm OD “B” Class G.I Pipe. Remaining frame – Is made by 100 x 50 x 2.5 mm rectangular pipe. Standing plate- Ø 300 mm OD X 10 mm thick M.S. plate. Seating plate- Ø 300 mm OD X 10 mm thick M.S. plate. Seating seat position and other two standing position plates are fixed 120 degrees each from other. Handle – Ø 33 mm “B” Class G.I. Pipe made by rolling. Top Closing cap – Dome shape made by PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Used is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60 mm OD seamless pipe. Pin – Made up of Ø 25mm M.S. bright bar. Circlips– A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166350/2023_2024 : Leg Press (Double) - specifications: Dimensions: (L X W X H) = 1676 x 400 x1500 mm. Main frame - Ø 114 mm OD “B” class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Foundations cover cap - dome shape of PP / NYLON / HDPE material. Link - is Ø 60 mm OD “B” Class GI pipe. Seat frame - Ø 42 mm OD “B” Class GI pipe. Leg Press back rest should be angled in 120 -130 degree. Foot rest - cast iron 124 x 296 x 5 mm thick and M.S plate of 2 mm thick use to support it. Seat & back rest – 380 x 275 x 60 mm thick high-density polyethylene (HDPE) blow molded with M10 integrated wall thickness 3 to 4 mm. Link connected with frame by 8 mm thick laser cutting MS profile. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closing cap’s- PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing- use is 6005 permanent lubricated reputed brand. Pin– Ø 25 mm M.S. bright bar pin. Bearing bushes - Ø 60 mm OD seamless pipe. Circlip– A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166351/2023_2024 : Rower - Supply and Installation of Rower having the following specifications: Dimensions: (L X W X H) = 1472 x 915 x 1040 mm. Upper and bottom pipes - Ø 88 mm OD “B” Class GI pipe. Foundation plate –M.S. round plate of Ø 250 mm & 8 mm thick. Handle - Ø 33 mm OD “B” Class G.I pipe. Angle between handle and horizontal surface is 75 - 80 degree. Linkages – Ø 48 mm OD “B” Class G.I. pipe. Seat & back rest – 380 x 275 x 60mm thick high-density polyethylene (HDPE) blow molded with M10 integrated wall thickness 3 to 4 mm. Foot resting pipe - Ø 60 mm OD “B” Class G.I. pipe. End Closing cap – dome shape made by PP / NYLON / HDPE material. Closing caps – PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø250 mm & 8mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Pin – Ø 25 mm M.S. bright bar pin. Circlips– A 24 circlips are used for assembly. Bearing bushes - Ø 60 mm OD seamless pipe / Bar. Bearing- use is 6005 permanent lubricated reputed brands. Grips – high quality rubber 46 mm OD. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166352/2023_2024 : Shoulder Builder (Double) - Supply and Installation of Shoulder Builder having the following specifications: Dimensions: (L X W X H) 890 x 558 x 1500 mm. Main frame - Made from Ø 114 mm OD “B” Class G.I. pipe. Foundation plate –M.S. round plate of Ø 250 mm & 8 mm thick. Foundation cover cap - dome shape of PP / NYLON / HDPE material. Shoulder ring pipe - Ø 33 mm OD “B” Class G.I Pipe. Shoulder ring pipe support – Ø 25 mm OD “B” Class G.I Pipe. Nylon knob with Bearing – Is fixed on shoulder ring pipe for rotating purpose (2 set to be fixed in a position for kids and adults). Top Closing cap’s- PP / NYLON / HDPE material. Closing cap – PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brands. Pin – Ø 25 mm M.S. bright bar pin. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick.<br>Bearing bushes - Ø 60 mm OD seamless pipe. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166353/2023_2024 : Sit-up Board - Supply and Installation of Sit-up Board having the following specifications: Dimensions: (L X W X H) 1570 x 450 x 660 mm. Main frame - made from Ø 33 OD “B” Class G.I. pipe bending design. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Leg Support - Ø 60 mm OD “B” Class G.I Pipe. Remaining Frame - Ø 60 mm OD “B” Class GI pipe and 100 X 50 MS pipe. Backrest Seat - made of M.S Checkered Plate Sheet of 3 mm thickness size 1100 mm x 310 mm. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166354/2023_2024 : Sky Walker - Supply and Installation of Sky Walker having the following specifications: Dimensions: (L X W X H) 1720 x 910 x 1700 mm. Main frame - Made of Ø 88 mm OD “B” class GI pipe dually bending design. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Paddle vertical support - Ø 42 mm OD “B” Class GI pipe. Handle - Ø 33 mm OD “B” Class GI pipe dually bending design. Leg movement frame – 50 mm x 50 mm x 2 mm thick square pipe. Footrest - cast iron 124 x 296 x 5 mm thick and M.S. plate of 2 mm thick use for to support it. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closing cap’s– PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm M.S pipe. and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber Ø 46 mm OD. Bearing- Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60 mm OD seamless pipe. Pin –Made of Ø 25mm M.S. bright bar. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166355/2023_2024 : Surfboard - Dimensions: (L X W X H) 1090 x 890 x 1390 mm. Main frame – Made from two pipes of Ø 114 mm OD “B” class GI pipe. Foundation plate –M.S. round plate of Ø 250 mm & 8 mm thick. Connecting pipe - Ø 88 mm OD “B” class GI pipe is used to connect both main frame pipes at top end and Ø 42 mm pipe is used to connect at bottom end. Handle - Ø 42 mm and Ø 33 mm OD “B” Class GI pipe. Support pipe – Ø 60 mm must be used to support leg movement frame. Leg movement frame– Ø 42mm OD “B” Class GI pipe. Footrest - cast iron 325 x 270 x 8 mm thick and M.S. plate of 250 x 200 x 2 mm thick use for to support it. Bracket - 8mm thick laser profile is use to support leg movement frame. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closing cap’s– PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber Ø 46mm OD. Bearing - Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60 mm OD seamless pipe. Pin – Made of Ø 25mm M.S. bright bar. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 80 -120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166356/2023_2024 : Cross Trainer (Double) - Supply and Installation of Double Cross Trainer having the following specifications: Dimensions: (L X W X H) 2280 x 550 x 1650 mm. Main frame- Made of Ø 88 mm OD “B” class GI pipe dually bending design. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Paddle vertical support - Ø 42 mm OD “B” Class GI pipe. Handle - Ø 33 mm OD “B” Class GI pipe dually bending design. Leg movement frame – 50 mm x 50 mm x 2 mm thick square pipe. Footrest - cast iron 124 x 296 x 5 mm thick and M.S. plate of 2 mm thick use for to support it. Top Closing cap – dome shape made by PP / NYLON / HDPE material. Closing cap’s– PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD B class G.I. pipe. and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Grips - High quality rubber. Bearing- Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60mm OD seamless pipe. Pin –Made of Ø 25mm M.S. bright bar. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 80-100 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166357/2023_2024 : Back Extension - Supply and Installation of Back Extension having the following specifications: Dimensions: (L X W X H) 1060 x 730 x 990 mm. Main frame - Made from Ø 88 mm OD “B” Class G.I. pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Leg Support - Ø 42 mm OD “B” G.I Pipe. Seat rest pipe – Ø 42 mm OD “B” Class G.I Pipe. Handle pipe – Ø 33 mm OD “B” Class G.I Pipe. Footrest - Cast iron 124 x 296 x 5 mm thick and M.S plate of 3 mm thick used to support it. Footrest pipe – Ø 42 mm OD “B” Class G.I Pipe and 80 x 40 mm MS rectangular pipe. Closing cap – PP / NYLON / HDPE material. Seat – 360 x 300 x 2 mm thick M.S. seat with corner fillet for safety. Grips - High quality rubber Ø 46 mm OD. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166358/2023_2024 : Push-up Bar and Dip Station - Supply and Installation of Push-up Bar and Dip Station having the following specifications: Providing and fixing Push Up Bar made from G.I. pipe. Dimensions: (L X W X H) 1220 x 530 x 1500 mm. Main frame - Ø 88 mm OD “B” class GI pipe. Leg & Hand Support - Ø 33 mm OD “B” class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Top Closing cap – Dome shape made by PP / NYLON / HDPE material. Closing cap’s- Plastic molded. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Coating - best quality of powder coating 80 - 120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166359/2023_2024 : Arm and Paddle Bike - Supply and Installation of Arm and Paddle Bike having the following specifications: Dimensions: (L X W X H) 990 x 500 x 880 mm. Main Frame –100 mm x 50 mm x 2.5 mm rectangular CR pipe with bending design. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Handle – Ø 33 mm OD “B” Class GI Round pipe dully bending design. Side and top cover – 1.6 mm thick MS laser cutting profile is used. Seat – 380 X 275 X 60 mm thick HDPE Blow moulding. Paddle –100 mm x 50 mm capsule pipe and 40 x 16 mm MS flat should be used for connecting the paddle and shaft. Closing cap’s – PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing bushes - Ø 60 mm OD seamless pipe. Bearing - Use is 6005 permanent lubricating sealed reputed brand. Shaft -Made up of Ø25mm OD MS Bright bar. Circlips– A 24 circlips are used for assembly. Coating - best quality of powder coating 80 - 120 micron. Safety Instructions and Exercise chart - start & finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166360/2023_2024 : Horse Rider - Supply and Installation of Horse Rider having the following specifications: Dimensions: (L X W X H) 1140 x 400 x 1400 mm. Main frame - Ø 114 mm OD 'B'; class GI pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Foundation cover cap - dome shape of PP / NYLON / HDPE material. Remaining frame – Is made by Ø 48 mm OD 'B'; class GI pipe. Seat frame – Is made by Ø 48 mm OD “B” class GI pipe. Seat position must be horizontal to 110 -120 degree. Link - made up of Ø 48 mm OD “B” Class G.I. pipe. Angle between link and ground position is 10-20 degree. Handle - Ø 33 mm OD “B” Class GI pipe. Paddle vertical support - Ø 60 mm OD 'B'; Class GI pipe. Handle frame- Ø 42 mm OD 'B'; Class GI pipe dually bending design. Foot pipe - Ø 33 mm OD “B” Class GI pipe. Support frame – 10 mm thick MS flat is used. Seat- Dimension 320 x 270 x 100 mm blow moulded wall thickness 4mm material HDPE. Bearing bush closing cap – PP / NYLON / HDPE material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded at top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Bearing - Use is 6005 permanent lubricated reputed brand. Bearing bushes - Ø 60mm OD seamless pipe. Pin – Made of Ø 25 mm M.S. bright bar. Grips - High quality rubber Ø 46 mm OD. Circlips – A 24 circlips are used for assembly. Coating - best quality of powder coating 60 to 70 micron. Safety Instructions and Exercise chart - start &finish position stick on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

od166361/2023_2024 : Single Bar - Supply and Installation of Single Bar having the following specifications: Dimensions: (L X W X H) 3550 x 2590 mm. Main frame - made from Ø 48 mm OD “B” Class G.I. pipe. Frame of Single Bar – Ø 33 mm OD “B” Class G.I. pipe. Foundation plate – M.S. round plate of Ø 250 mm & 8 mm thick. Top Closing cap’s - Decent Design Size PP / HDPE / MS. Material. Foundation stool: Made from main pipe Ø 88 mm OD M.S pipe and top support of M.S. round plate of Ø 250 mm & 8 mm thickness is welded top. Square tube of 30 x 30 x 2 mm must be used to support center pipe. Height of stool is 3 ft. Foundation stool is embedded in C.C. stock below ground level. Coating - best quality of powder coating 80-120 micron. Safety Instructions and Exercise chart – Made from Aluminum / stainless-steel stick-on product. All joints must be robotic welded and zinc primer paint should be applied at all the welding points prior to finishing.

Inauguration stone

od166386/2023_2024 : Providing and fixing 18 mm thick gang saw cut, mirror polished, pre-moulded and pre polished, machine cut for inauguration granite stone of required size, approved shade, colour and texture laid over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) joint treated with white cement, mixed with matching pigment, epoxy touchups including rubbing, curing etc. complete at all levels. Area of slab over 0.50 sqm

16.21 : Engraving letters in hard stone

13.71 : Lettering with black Japan pint of approved brand and manufacture