Public Works Department Tender

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.83.2:Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

50.17.1.3:Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

14.82:Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge

17.2.1:Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:W.C. pan with ISI marked white solid plastic seat and lid

OD1123/2024-2025:Supplying fixing 15 mm dia or nearest size C.P long body tap.

50.17.1.4:Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge.

18.54.1:Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 86 mm long, weighing not less than 88 gms

9.48.1:Providing and fixing M.S. Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.1:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium ( anodised transparent or dyed to required shade according to IS : 1868, Minimum anodic coating of grade AC 15)

OD239844/2024-2025:Providing and fixing fixing 4 mm ACP sheet in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws EPDM rubber/ neoprene gasket etc. complete as per architectural drawings and directions of Engineer - in- Charge.

21.3.2:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

15.23.1:Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead.For thickness of tiles 10 mm to 25 mm

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

OD15607/2024-2025:Providing and laying vitrified floor tiles (double charged/full body-glassed/mat finished of brands Rak/Kajaria/equivalent brands) using spacers if necessary of minimum dimension of tile 600mm and above (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints having 3 mm width with epoxy grout mix 0.7kg of organic coated filler of desired shade (0.1 kg of hardener and 0.2kg of resin per kg) as and when required including filling grouting and finishing complete as per direction of Engineer in charge

50.18.9.19.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

OD239846/2024-2025:Engaging Fitter (grade 1)

OD239847/2024-2025:Engaging Coolie

Microbiology Lab

OD15551/2024-2025:Supply of ISLAND BENCH of length 2900mm and 1200 mm wide using 18mm thick melamine laminated boiled water proof plywood worktop (750mm height from F.F.L) Complete with; • Two number of 400mm wide under bench cabinet having one drawer, one adjustable shelf and one door with lock • Four number of 450mm wide under bench cabinet having one drawer, one adjustable shelf and one door with lock • Two Cpu trolley and keyboard tray • Four cable grommets. • Four number of 16 Amp/220 Volt double electrical outlet and two nos of single computer data outlet. • Including filler panel and knee space panel. Size: 2900x1200x750mm(H) Specifications Of Wall Bench: MELAMINE LAMINATED PLYWOOD WORKTOP: The worktop will be made of 18 (±1) mm thick High pressures Melamine laminate boiled water proof plywood. Finish – High quality HPL (High pressure Melamine laminate) of 0.6mm hot pressed on both the sides. The exposed edges of the worktop will be sealed with minimum 3(±1) mm thick high quality PVC edges. For strong bonding and durability, the lamination and edging will be machine pressed at high temperature and pressure. The Melamine Laminated plywood conforms to BS, NEMA & BIS Standards. All worktops will have 80mm glued back splash for wall benches, of the same material. For the floor standing or plinth mounted cabinets, the work top will be supported by the cabinets which rest on the floor without any additional support of any steel frameworks. Panel supports are provided if additional supports are needed. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof)plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Cable gromet: The cable gromet on the work surface will be flexible plastic component for easy and safe passage of wires. Cpu Trolley: It will be made of steel and used to Store C.P.U. under the table and saves space. Soft anti-vibration pads provided. No tools needed for adjusting width range & CPU trolley will have caster wheels for movement. Width adjustment of 95 mm provided (width range 115 mm min. & 210 mm max). Key board tray: Ergonomic Key Board trays will be molded and made of ABS material.

OD15603/2024-2025:Supply of L-shape bench of length 6680mm + 3690mm 750mm wide with 16mm thick Trespa worktop Complete with; • One number 450mm wide under bench cabinet having one adjustable shelf and one door with lock. • Five number 900mm wide under bench cabinet having one adjustable shelf and two doors with lock. • Four number 900mm wide under bench cabinet having 2 drawers, one adjustable shelf and two doors with lock • one number 900mm wide under bench sink cabinet • including front+ back frame, middle frame, side frame corner support , filler panel and knee space panel • one number TOF Italy make single cold water standout • one number 450x350mm size(inner) polypropylene sink • Six number of 16 Amp/220 Volt double electrical pedestal box • Two tier reagent rack 250 mm wide 2000mm long Size: 6680+3690mmx750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS1293 1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x27cm (depth). The sink should not have any sharp corners inside. Sink color shall be black All sinks shall be supplied with bottle trap.

OD15550/2024-2025:Supply of WALL BENCH of length 2400mm and 600 mm wide using 18mm thick melamine laminated boiled water proof plywood worktop(750mm height from F.F.L) Complete with; • Two number of 400mm wide under bench cabinet having one drawer, one adjustable shelf and one door with lock • Two Cpu trolley and keyboard tray • Two cable grommets. • Two number of 16 Amp/220 Volt double electrical outlet and two nos of single computer data outlet. • Including filler panel and knee space panel Size: 2400x600x750mm(H) Specifications Of Wall Bench: MELAMINE LAMINATED PLYWOOD WORKTOP: The worktop will be made of 18 (±1) mm thick High pressures Melamine laminate boiled water proof plywood. Finish – High quality HPL (High pressure Melamine laminate) of 0.6mm hot pressed on both the sides. The exposed edges of the worktop will be sealed with minimum 3(±1) mm thick high quality PVC edges. For strong bonding and durability, the lamination andedging will be machine pressed at high temperature and pressure. The Melamine Laminated plywood conforms to BS, NEMA & BIS Standards. All worktops will have 80mm glued back splash for wall benches, of the same material. For the floor standing or plinth mounted cabinets, the work top will be supported by the cabinets which rest on the floor without any additional support of any steel frameworks. Panel supports are provided if additional supports are needed. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Cable gromet: The cable gromet on the work surface will be flexible plastic component for easy and safe passage of wires. Cpu trolley: It will be made of steel and used to Store C.P.U. under the table and saves space. Soft anti-vibration pads provided. No tools needed for adjusting width range & CPU trolley willhave caster wheels for movement. Width adjustment of 95 mm provided (width range 115 mm min. & 210 mm max). Key board tray:Ergonomic Key Board trays will be molded and made of ABS material.

OD15549/2024-2025:WASHING AREA-01 (BC) Supply of L-shape bench of length 2330mm + 1550mm 750mm wide with 16mm thick Trespa worktop Complete with; • One number 570mm wide under bench cabinet having one adjustable shelf and one door with lock. • One number 600mm wide under bench cabinet having one adjustable shelf and one door with lock. • One number 900mm wide under bench cabinet having 2 drawers, one adjustable shelf and two doors with lock • One number 900mm wide under bench sink cabinet • including front+ back frame, middle frame, side frame corner support, filler panel and knee space panel • one number TOF Italy make single cold water standout • one number 600x450mm (Inner)size polypropylene sink • One number of 16 Amp/220 Volt double electrical pedestal box. Size: 2330+1550x750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specificpressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lippingof 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius.Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS- 1293 1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Polypropylene sink: It shall be of Polypropylene. The dimensions of the sink are 60x45x30cm(depth)(Inner). The sink should not have any sharp corners inside. Sink color shall be black. All sinks shall be supplied with bottle trap.