Public Works Department Tender

13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

50.18.9.19.1:Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.22.1:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

OD16410/2024-2025:Engaging Coolie

CP LAB

OD16374/2024-2025:WASHING AREA-02 (CP) Supply of L-shape bench of length 5499mm + 2439mm 750mm wide with 16mm thick Trespa worktop Complete with; Two number 1200mm wide under bench cabinet having one adjustable shelf and two doors with lock. Two number 1000mm wide under bench cabinet having 2 drawers, one adjustable shelf and two doors with lock. Two number 800mm wide under bench sink cabinet. One number 1000mm wide under bench plinth mounted cylinder storage cabinet. including front+ back frame, middle frame, side frame corner support , filler panel and knee space panel. Two number TOF Italy make single cold water standout. Two number 450x350mm size polypropylene sink(inner size) Four number of 16 Amp/220 Volt double electrical pedestal box. One number of single gas(lpg) stand out Size: 5499+2439x750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lippingof 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Gas fittings: ? It will be made of brass (UNI 5705 -65) and will have an epoxide covering in White color. ? Connection: G3/8 and G1/2 UNI ISO 228/1. ? Nozzle: olive type fixed as per standard DIN 12898. ? Upper part: with ceramic valve spring loaded for safety, maintenance free. ? In security for your best choice gas fittings aremanufactured in accordance with DIN DVGW regulations. Maximum working pressure: 0.2 bar. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x27cm(depth)(Inner). The sink should not have any sharp corners inside. Sink color shall be black. All sinks shall be supplied with bottle trap

OD16375/2024-2025:Supply of WALL BENCH of length 1500mm and 750 mm wide using 16mm thick Trespa worktop Complete with;  One number 900mm wide under bench cabinet having one adjustable shelf and two doors with lock.  One number 500mm wide under bench cabinet having 1 drawers, one adjustable shelf and one doors with lock  including front+ back frame, middle frame, side frame, filler panel and knee space panel  One number of 16 Amp/220 Volt double electrical pedestal box.\ Size: 1500x750x900mm(H) Specifications Of Wall Bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grab rail – Full length extruded anodized aluminum grab rail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified.

OD16376/2024-2025:Supply of L-shape bench of length 3000mm + 1500mm 750mm wide with 16mm thick Trespa worktop Complete with;  One number 900mm wide under bench cabinet having one adjustable shelf and two doors with lock.  One number 1000mm wide under bench cabinet having one adjustable shelf and two door with lock.  One number 500mm wide under bench cabinet having 1 drawers, one adjustable shelf and one doors with lock  One number of 1200mm wide under bench cabinet having one drawer, one adjustable shelf and one door with lock  including front+ back frame, middle frame, side frame corner support , filler panel and knee space panel  Three number of 16 Amp/220 Volt double electrical pedestal box. Size: 3000+1500x750x900mm(H) Specifications of wall bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lippingof 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified.

OD16377/2024-2025:Supply of WALL BENCH of length 3000mm and 750 mm wide using 16mm thick Trespa worktop Complete with;  One number of 1200mm wide under bench cabinet having one drawer, one adjustable shelf and one door with lock.  One number 900mm wide under bench sink cabinet  including front+ back frame, middle frame, side frame, filler panel and knee space panel  one number TOF Italy make single cold water standout.  one number 450x350 mm size polypropylene sink(Inner size)  One number of 16 Amp/220 Volt double electrical pedestal box. Size: 3000x750x900mm(H) Specifications Of Wall Bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grab rail – Full length extruded anodized aluminum grab rail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work.The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 5/15 Amp/220 Volt single, double electrical sockets which fully confirms to IS1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Water fittings: Fittings shall be made of brass (UNI 5705 -65) and should have an epoxide covering in White color. Fittings shall be manufactured as per modern technologies & comply to DIN 12920 standards for the best performance. Polypropylene sink: It shall be of Polypropylene, molded as one piece. The dimensions of the sink are 45x35x270cm(depth)(inner size). The sink should not have any sharp corners inside. Sink color shall be black. All sinks shall be supplied with bottle trap.

OD16378/2024-2025:Supply of PENINSULAR BENCH of length 3000mm and 1500mm wide using 16mm thick Trespa worktop. Complete with;  Two number 1000mm wide under bench cabinet having one adjustable shelf and two doors with lock.  Two number 1200mm wide under bench cabinet having 2 drawers, one adjustable shelf and two doors with lock  including front+ back frame, middle frame, side frame corner support , filler panel and knee space panel  One number of 16 Amp/220 Volt double electrical pedestal box at 180 degree  One number of 16 Amp/220 Volt quadruplet electrical pedestal box Size: 3000mmx1500x900mm(H) Specifications of peninsular bench: Trespa worktop: Antibacterial and highly chemical resistant TopLab®PLUS is the perfect surface for quality worktops with inherent antibacterial properties and highly resistant to a wide variety of aggressive chemicals. Trespa Top Lab Plus worktop is a solid laboratory bench panel to EN 438-4:2005 of thicknesses of 16mm greater for interior scientific surface solutions. Sheets consisting of layers of wood-based fibers (paper and/or wood) impregnated with thermosetting resins and surface layer(s) on one or both sides, having decorative colors. A transparent topcoat is added to the surface layer(s) and cured by Trespa’s unique proprietary in-house technology Electron Beam Curing (EBC), to enhance the scratch and chemical resistance. These components are bonded together with simultaneous application of heat (≥ 150° C / ≥ 302° F) and high specific pressure (> 5 MPa) to obtain a homogeneous non-porous material with increased density and integral decorative surface. This process guarantees a pore-free, closed surface which is resistant to a multiple of aggressive chemicals, anti-bacterial, easy to clean, disinfect and maintain. The level of scratch resistance is equal or above 4 Newton according to EN 438-2:12. The worktops shall have minimum joints. All worktops will have 80mm glued back splash for wall benches, of the same material. The worktops shall be either silver grey or black colour uniformly though out the surface. Test reports from the manufacturer will be provided. TRESPA TOP LAB PLUS is manufactured in NETHERLANDS by TRESPA B.V. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lippingof 3(± 1) mmto protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Support Frame Work: The support frame design will be of cantilever type, with sliding facility for hanging cabinets on the framework itself. Worktops will be supported by this heavy duty steel frame work. The frame shall be of heavy duty rectangular box with a minimum wall thickness of 14 gauge and members shall be made of 60x40 mm CR tubes. Worktops and all under-bench cabinets will be supported by this frame work. The under bench cabinets will be able to slide to create knee space as necessary. The frame work will be de – greased and epoxy powder coated with the thickness of 80 – 90 microns for smooth finish and protection. The profile ends will be covered and protected with injection moulded ABS end-caps. Adjustable leveling jacks of tough plastic/nylon will be provided for each leg for the support of the frame. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Sleek, Robust and Small Electrical pedestal boxes will be made of 1.2mm thick CRCA sheets to accommodate, single or double sockets and switches. The pedestal will take only very minimum space on the work table .The Pedestal boxes will be epoxy powder coated to min 80 microns for good finish and aesthetic look. Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified

OD16379/2024-2025:Supply of PENINSULAR BENCH of length 2400mm and 1200 mm wide using 18mm thick melamine laminated boiled water proof plywood worktop(750mm height from F.F.L) complete with; ? Four number of 400mm wide under bench cabinet having one drawer, one adjustable shelf and one door with lock ? Two CPU trolley and keyboard tray ? Four cable grommets. ? Four number of 16 Amp/220 Volt double electrical outlet and two number of of single computer data outlet. ? Including filler panel and knee space panel. Size: 2400x1200x750mm(H) Specifications Of Wall Bench: MELAMINE LAMINATED PLYWOOD WORKTOP The worktop will be made of 18 (±1) mm thick High pressures Melamine laminate boiled water proof plywood. Finish – High quality HPL (High pressure Melamine laminate) of 0.6mm hot pressed on both the sides. The exposed edges of the worktop will be sealed with minimum 3(±1)mm thick high quality PVC edges. For strong bonding and durability, the lamination and edging will be machine pressed at high temperature and pressure. The Melamine Laminated plywood conforms to BS, NEMA & BIS Standards.All worktops will have 80mm glued back splash for wall benches, of the same material. For the floor standing or plinth mounted cabinets, the work top will be supported by the cabinets which rest on the floor without any additional support of any steel frameworks. Panel supports are provided if additional supports are needed. Under bench cabinet specification: Door/ Drawer Front: It should be made of 18 mm thick BWP (Boiled Water Proof) plywood, laminated with 0.6 mm thick melamine laminates on both sides. The lamination should be done by hot press with a minimum pressure of 90 tones. All exposed edges are lipped with PVC lipping of 3(± 1)mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. The Melamine Laminate should confirm to BS, NEMA & BIS Standards. Doors/drawer of all under bench cabinets with Grabrail – Full length extruded anodized aluminum grabrail which are epoxy powder coated to 80-90 micron thickness. Where specified good quality locks and keys will be provided for cabinets. Cabinet Body: Cabinet body is made out of 18mm thick BWP plywood laminated with 0.6 mm thick melamine on both sides. The lamination is done with hot press with minimum of 90 tones pressure. All exposed edges are lipped not less than 0.5 mm to protect from moisture and insects. The lipping is machine applied with hot melt glue at a temp of 205 degree Celsius or above. The Cabinet body is made of permanent casework without any screws and knockdown / mini-fix fittings. Permanent case work shall be made using latest technology such as biscuit joints with necessary adhesives. Inside of the cabinet body there are no any gaps for dust accumulation. All joints are sealed and it should be easily cleanable. All Adjustable shelves are also made with the same material as above. Hinges: Nickel coated heavy duty; self-closing hinges are provided which allows an opening up to 165 degree wide and are adjustable in all three directions for perfect finish and corrections. Filler panel: It shall be made of 18mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. All exposed edges are lipped with PVC lipping of 3(± 1) mm to protect from impacts, moisture and insects. The lipping is of the machine applied with hot melt glue at a temperature of 205 degree Celsius. Knee space panel: It shall be made of 9 mm thick BWP plywood laminated, with 0.6mm thick melamine on both sides. The lamination should be done with hot press with minimum 90 tons of pressure. Electrical fittings: Supply will be standard 6/16 Amp/220 Volt single, double electrical sockets which fully confirms to IS-1293-1988. Flame retardant, UV stabilized, unbreakable polycarbonate casing. Connector of phosphor bronze to provide high conductivity, flexibility and contact pressure. Silver plated (7 microns) brass terminals to reduce heating and improve conductivity. To be encased in metal pedestal box, for mounting on to bench work tops or on service pillars. Switches will be Piano type unless otherwise specified. Cable gromet: The cable gromet on the work surface will be flexible plastic component for easy and safe passage of wires. Cpu Trolley: It will be made of steel and used to Store C.P.U. under the table and saves space. Soft anti-vibration pads provided. No tools needed for adjusting width range & CPU trolley will have caster wheels for movement. Width adjustment of 95 mm provided (width range 115 mm min. & 210 mm max). Key board tray: Ergonomic Key Board trays will be molded and made of ABS material.