Public Works Department Tender

Code No. 16.115:- Applying two coats of cement based polymer modified bonding admixture (FOSROC or equivalent) over the existing RCC members after removing the plastering and cleaning the concrete surfaces and saturated with clean water. The cost including all materials labour charges

Code No. 4.1.3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size)

Code No. 11.36B:- Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) , of approved make (Jhonson / Asian / Somany / Nitco) in all colours , shades of size 300 x 450 mm as approved in skirting , risers of steps and dados, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement with pigment of matching shade complete - size 300x450 mm

Code No. 1140.1:- Providing and laying rectified ceramic rustic / matt finish floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make (Somany / Nitco) in all colours , shades, except white, ivory, grey, fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments etc.,

Code No. 9.118.1:- Providing and fixing to existing door frames - 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59 x 24 mm and wall thickness 2 mm (+- 0.2 mm) with inbuilt edging on both sides . The styles and rails mitred and joint at the corners by means of M.S. galvanised / plastic brackets of size complete 75 x 220 mm having wall thickness 1.0 mm and stainless steel screws . The styles of the shutter reinforced by inserting galvanised M.S.tube of size 20x20 mm and 1mm (+- 0.1mm) wall thickness . The lock rail made up of 'H' section , a uPVC hollow section of size 100 x 24 mm and 2 mm (+-0.2 mm) wall thickness , fixed to the shutter styles by means of plastic / galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multichambered single panel of size not less than 620 mm, having overall thickness of 20 mm and 1 mm (+_ 0.1mm) wall thickness . They panels filled vertcally and tie bar at two places by inserting horizontally 6 mm galvanised M.S.rod and fastened with nuts and washers , complete as per manufacturer's specification (For W.C. and bathroom door shutter)

Code No. 17.7.8:- Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps ,32 mm C.P.brass waste of standard pattern , including painting of fittings and brackets ,cutting and making good the walls wherever required - white vitreous china surgeon type wash basin size 660x460 with a pair of 15mm C.P.brass pillar taps with elbow operated levers

Code No. 17.32.2:- Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing - rectangular shape 453 x 357 mm

Code No.18.54.2:- Providing and fixing PTMT bib cock of approved quality and colour - 15mm nominal bore, 122 mm long , weighing not less than 99 gms

Code No. 17.2.2:-Providing and fixing white vitreous china pedestal type water closet (European type W.C.pan) with seat and lid, 10 litre low level white P.V.C. flusing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS: 7231,with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required - W.C. pan with ISI marked black solid plastic seat and lid

Code No. 17.78.1:- Providing and fixing CP brass health faucet of approved quality - 15 mm nominal bore

Code No. 9.6.3:-Providing and fixing 35mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15 : 2001 (Part B) , including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, all complete and panelling with panels of - 12mm thick one side pre - laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1 , medium density flat pressed , three layer particle board FPT - I or graded wood particle board FPT - I , conforming to IS : 3087 , bonded with BWP type synthetic resin adhesive as per IS : 848 and prelaminated conforming to IS : 12823, Grade 1, type - II marked

Code No. 11.41.2c:- Providing and laying fully vitrified floor tiles of size 600 x600 mm (thickeness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 of approved make (Nitco / Rak / Johnson / Asian ) in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) , including grouting the joints with white cement and matching pigments etc., complete - size of tile 600x600mm - Commercial quality

Code No. 8.2.2.1:- Providing and fixing 18mm thick gang saw cut, mirror polished (premolded and prepolished) machine cut for kitchen platforms,vanity counters,window sills,facias and similar locations , of required size, approved shade,colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing,curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels - Granite of any colour and shade - Area of slab upto 0.50 sqm

Code No. 8.3.2:- Providing edge moulding to 18mm thick marble stone counters ,vanities etc., including machine polishing to edge to givehigh gloss finish etc. complete - Granite work

Code No. 15.56:- Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead

Code No. 31.161.1F:- Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,excluding UPVC specials such as bends,tees, threaded pieces, couplers,reducer,endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia

Code No. 31.161.1D:- Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore / Nandi) (0.6 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement,UPVC specials such as bends,tees, threaded pieces, couplers, reducer,endcaps etc.,complete all as per IS and CPWD specification. - 75mm dia.

Code No. 18.74.1:- Providing and fixing unplasticised P.V.C. connection pipe with PTMT nuts, collar, and bush of approved quality and colour - 15 mm nominal bore with 30 cm lenghth

Code No. 17.60.1.1:- Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors - 100mm inlet and 100mm outlet - sand cast iron S&S as per IS: 3989