Public Works Department Tender

Code No. 14.54.1:-Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work

Code No. 9.1.2I:-Providing wood work in frames of doors , windows, clerestory windows and other frames , wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately) - Irul wood

Code No. 9.6.3:-Providing and fixing 35mm thick factory made laminated veneer lumber door shutter conforming to IS : 14616 and TADS 15 : 2001 (Part B) , including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws, all complete and panelling with panels of - 12mm thick one side pre - laminated particle board (decorative lamination on one side and other sides balancing lamination) grade - 1 , medium density flat pressed , three layer particle board FPT - I or graded wood particle board FPT - I , conforming to IS : 3087 , bonded with BWP type synthetic resin adhesive as per IS :848 and prelaminated conforming to IS :12823, Grade 1, type - II marked

Code No. 10.25.2:-Steel work welded in built up sections / framed work , including cutting,hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required - in gratings, frames, guard bar, ladder, railings, brackets,gates and similar works

Code No. 13.61.1:-Painting with synthetic enamel paint of approved brand and manufacutre to give an even shade - Two or more coats on new work

Code No.15.12.1:-Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead - of area 3 sqm and below

Code No. 15.56:-Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead

Code No. 14.1.1:-Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq.metres and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead - with cement mortar 1:4 (1 cement : 4fine sand)

Code No. 16.115:-Applying two coats of cement based polymer modified bonding admixture (FOSROC or equivalent) over the existing RCC members after removing the plastering and cleaning the concrete surfaces and saturated with clean water. The cost including all materials labour charges

Code No. 9.147D.1:-Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50m in height dimension comprising of uPVC multi - chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 + or - 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile , zinc alloy (white powder coated) touch locks with hook , zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I. fastners 100 x8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shyall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality , all complete as per approved drawing.(Single / double glass panes , wire mesh and silicon sealent shall be paid separately) - Two track two panels sliding window made of (small series) frame 52 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 + or -0.2 mm and single glazing bead of appropriate dimension.(Area of window upto 1.75 sqm) - sliding window size 1.20x1.35 m

Code No. 7.100.1:-Laterite Stone Masonry for building work using neatly dressed Laterite Stone of size 30x20x20 cm in cement mortar 1:4 (1 cement : 4 Coarse sand ) for foundation and basement

Code No. 4.1.4:-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40mm nominal size)

Code No. 4.1.10:-Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plith level - 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size)

Code No. 13.1.2:-12mm cement plaster of mix -1:6 ( 1 cement : 6 fine sand)

Code No. 2.27:-Supplying and filling in plinth with river sand under floors, including watering, ramming consolidating and dressing complete

Code No. 31.162.1D:-Providing, laying and jointing UPVC pipes(Finolex / jain / Supreme / Truebore /Nandi) (0.4 Mpa)conforming to IS specification 4985 and ISI marked including transportation to the site , lowering to the trenches, laying to proper grade and alignment, testing of joints with required testing equipment,including cost of solvent cement, excluding UPVC specials such as bends, tees, threaded pieces, couplers, reducer, endcaps etc.,complete all as per IS and CPWD specification. - 110mm dia.

Code No. 19.7.1.1:- Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), foundtion concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design - inside size 90x80 cm and 45 cm deep including C.I.cover with frame (light duty ) 455 X 610 mm internal dimensions , total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) - with common burnt clay F.P.S. (non modular ) bricks of class designation 7.5

Code No. 17.1.1:-Providing and fixing water closet squatting pan (Indian type W.C.pan) with 100 mm Sand Cast Iron P or S trap, 10 litre low level white P.V.C flusing cistren, including flush pipe , manually controlled device (handle lever) conforming to IS : 7231 , with all fittings and fixtures complete , including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C.pan of size 580x440mm with integral type foot rests.

Code No. 15.41:-Dismantling cement asbestos or other hard board ceiling or partion walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead

Code No. 16.97:-Providing and fixing PVC false roofing with the existing PVC cabin using sintex PVC section of size 6mm x 250 mm , having interlocking facilities supported in the PVC extruted multi chamber frame section of 40 x 48 mm , with necessary MS / Stailess screws. The rate includes the cost of sintex PVC section , labour charges for fixing and transport etc.complete

Code No. 15.57:-Dismantling aluminium / gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead

Code No. 21.1.2.2:-Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / appropriate Z sections and other sections of approved make conforming to IS:733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions , i.e at top, bottom and sides with required EPDM rubber / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling , C.P.brass / stainless steel screws , all complete as per architectural drawings (Glazing, paneling and dash fasteners to be paid for separately) - for shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powder coating 50 micron)

Code No. 21.2.2:-Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS:12823 grade I type II , in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings- Pre - laminated particle board with decorative lamination on both sides

Code No. 21.3.3:-Providing and fixing glazing in aluminium door, window , ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings ( cost of aluminium snap beading shall be paid in basic item) - with float glass panes of 8 mm thickness

Code No. 11.41.2A + Code No. 11.42:-Providing and laying fully vitrified floor tiles of size 600 x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622 of approved make (Nitco / Rak / Johnson /Asian ) in all colours and shades , laid including grouting the joints with white cement and matching pigments etc., complete - size of tile 600 x600 mm

Code No. 11.43:-Fixing glazed /ceramic / Vitrified floor tiles with cement based high polymer modified quick - set tile adhesive (water based) conforming to IS:15477, in average 3 mm thickness - ( Using 5 kg adhesive per sqm of tile area)