National Institute Of Technology Tender

Steel reinforcement for R.C.C. work in Thermo-Mechanically Treated bars of grade Fe-500D or more.including straightening, cutting, bending, placing in position and binding all complete upto plinth leve

Providing and fixing plywood 4 mm thick, one side decorative veneer facings of approved manufacture conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with :

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).

Providing and fixing first class teak wood 35 mm thick fully panelled shutters or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)

Providing and fixing Head Board cushion for Cot using with 50mm thick upholstery foam and covered with high quality Rexine of approved make in all colors and shades in required grid type and fixed in 9mm plywood conforming IS:710 and fixing in existing cot etc complete as per direction of Engineer in Charge.

Providing and fixing Head Board cushion for Cot using with 50mm thick upholstery foam and covered with high quality Cloth of approved make in all colors and shades in required grid type and fixed in 9mm plywood conforming IS:710 and fixing in existing cot etc complete as per direction of Engineer in Charge.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing high quality ISI marked stainless steel auto soft close hinges of specified size with stainless steel screws etc. complete

Providing and fixing IS : 3564 aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing 40 mm special quality chromium plated brass cupboard locks with six levers of approved quality including necessary screws etc. complete.

Providing and fixing 125 mm aluminium powder coated handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing Single aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing double strip magnetic catcher (horizontal type)high quality ISI marked of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Providing and fixing powder coated heavy duty telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer-in charge.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections profile size 42x50 mmhaving an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer specification and direction of Engineer- in-charge

Providing and fixing 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of H section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter to existing door frames)

Providing and fixing 47 mm thick factory made uPVC door shutters including uPVC door frame made of shutter styles and rails of a uPVC hollow section of size 47X125 mm and mullion with 47X109 wall thickness 2.5 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets wall thickness 2.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube. The lock rail made up of H section, a uPVC hollow section, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 30 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, etc and door frame made of uPVC extruded frame sections profile size 60X90mm having an overall dimension as below (tolerance ±0.2mm), with wall thickness 2.5 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube and stainless steel hinges fixed to the frame, including all fittings, door lock etc complete as per manufacturer specification and direction of Engineer in charge

Providing and fixing 12 mm thick marine plywood gurjan or equvalent confirming to IS:710 for cupboards, shelves, partition, drawers, table top etc. including necessary screws etc. complete.

Providing and fixing 20 mm thick marine plywood or gurjan confirming to IS:710 for cupboards, shelves, partition, drawers, table top etc. including necessary screws etc. complete.

Providing and fixing bright /matt finished 125 mm Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Providing and laying vitrified antiskid mat finish floor tiles in 600x600mm sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement/epoxy and matching pigments etc., complete.

Grouting the joints of flooring tiles 600x600 mm having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.

Providing and fixing (Gypsum board 12.5mm thick) false ceiling at all height including providing and fixing of frame Work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms or sqm (both side inclusive) as per IS : 277 and consisting of Angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition withthe help of rawl plugs at 450 mm centre, with 25mm long dry wall screws at 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c including jointing and finishing to a flush finish of tapered and square edges of the board with Recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of Perimeter channels suitably fixed, all complete as per drawings, specification and Direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS Certification marks)

Providing and fixing 12.5 mm thick tapered edge gypsum moisture resistant board false ceiling at all height including providing and fixing of frame Work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms or sqm (both side inclusive) as per IS : 277 and consisting of Angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition withthe help of rawl plugs at 450 mm centre, with 25mm long dry wall screws at 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c including jointing and finishing to a flush finish of tapered and square edges of the board with Recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturers specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of Perimeter channels suitably fixed, all complete as per drawings, specification and Direction of the Engineer in Charge but excluding the cost of painting with:

Plastering with C.M. 1:4 (one cement four sand), 12mm thick for walls inside and outside with necessary scaffolding and thread lines, including cost and conveyance of all materials and labour charges etc. complete.

Finishing walls with two or more coat Acrylic Smooth exterior paint of required shade in New work (applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with two or more coats synthetic enamel paint of approved brand and manufacture to give an even shade using spraying machine on new work:

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and applying best quality wood putty of approved brand and manufacturer, including cost for thinner, over wood surface to prepare the surface even and smooth complete

Wall painting with two coat premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre asper instruction of engineer in charge

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Painting with synthetic enamel paint one or more coats on old work of approved brand and manufacture of required colour to give an even shade

Painting with one or more coats epoxy paint on old work of approved brand and manufacture of required colour to give an even shade :

French spirit polishing one or more coats on old work

Finishing walls with water proofing cement paint of required shade over old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat.

Melamine polishing on wood work (one or more coat).

Renewing float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm), with wooden fillets wherever necessary

Taking out existing door/window shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge

Dismantling doors, windows and clerestory windows (steel or wood) shutter Of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking serviceable material in Engineering Unit store and other materials within 50 metres lead as per the instructions of Engineer-in-Charge

Dismantling doors, windows and clerestory windows (PVC or Plywood) shutter Of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking serviceable material in Engineering Unit store and other materials within 50 metres lead as per the instructions of Engineer-in-Charge

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead

Providing and fixing white vitreous china pedestal type water closet suit model two in one (European type W.C. pan) with white solid plastic seat cover with manually controled device (air sucking type)i with all fittings and fixtures complete, including cutting and marking good the walls and floors wherever necessary including cost and conveyance of all materials and labour charges etc required as per instruction of officials

Providing and fixing White Vitreous China Flat back table top wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required

Providing and fixing 110 mm steel gratings (door type) including cost and conveyance of all materials and labour charges etc. complete.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Supplying and fixing 600mm x 20mm brass towel rail and fixing to wall with wooden plug with CP brass screws including cost and conveyance of all materials and labour charges etc. complete.

Providing and fixing 600mm SS towel rail inside walldrobe complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour

Providing and fixing 25 mm PVC pipes (3/4") (10kg/cm2) , including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

Providing and fixing 63 mm PVC pipes (2")(4kg/cm2) , including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (20 mm nominal outer dia Pipes), having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing best quality C.P. brass health fauset (Cascade) etc. complete

Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing SS soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for fixed portion of doors, windows ,sliding windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)(Glazing, paneling and dash fasteners to be paid for separately) :

Providing and fixing 4mm or nearest thick Aluminium composite panel (ACP) two side finish board in paneling fixed in aluminium doors, windows shutters and partitions frames with CP. brass/stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing 12mm or nearest thick multiwood particle board(solid sheet)( 6 dense) in paneling fixed in aluminium doors,windows,shutters and partitions frames with CP/brass syainless steel screws etc,complete as per acrchitectural drawing and direction of engineer in charge

Providing and fixing glazing with float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)

Providing and fixing metalic (SS 306,316 or equvalent) mosquito net of approved quality over aluminium frame work including cost and conveyance of all materialsand labour charges etc. complete but excludingcost of aluminium etc. complete

Providing and laying water proofing treatment on roofs of slabs by applying cement based two component polymer modified water proofing slurry coating (SIKA TOP seal or equivalent) after cleaning the surface free from scale,rust, grease, oil etc. preparing the surface to be true and flat and saturated mixing the liquid (A) and powder (B) components in the ratio 1:4 by weight,applying in two coats with an interval of 2 to 6 hours for hardening in between and finally finished by rubbing down with a soft, dry sponge including protecting the applied surface from direct sunlight and strong wind and curing by gunny bags or polythene sheeting upto 5 days etc. complete

Chipping and removing the damaged portion of R CC beams columns slabs etc. carefully without damaging the existing structure including removing the debries scrapping with emery paper/wire brush for removing the rusted portion from the reinforcement apply one coat of adhesive epoxy resine such as NETTO BOND EP including cost and conveyance of all materials and all labour charges etc. complete.

Providing and fixing room sign board in 2mm thick stainless steel plate size of 200x100mm, including lettering by engraving and carving (up to 3 Nos), as per direction in Engineer in charge.