National Institute Of Technology Tender

CEMENT CONCRETE (CAST IN SITU)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete :

1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

WOOD AND P. V. C. WORK

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Fixed to steel windows by welding

STEEL WORK

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.

Using M.S. angels 40x40x6 mm for diagonal braces

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

GI Tubular TATA or equvalent

ROOFING

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50mm (base metal of minimum 0.45mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing square type UPVC gutter with necessary clamps, bolts, nuts and specials such as nozzles sockets stoppers etc. including cost and conveyance of all materials and labour charges etc. complete as per the instructions of the dept. officers

200mm or equivalent Square type UPVC

FINISHING

12 mm cement plaster of mix :

1:4 (1 cement: 4 fine sand)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade

Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface

Old work (one or more coats applied @0.83 Itr/10 sqm).

WATER SUPPLY

Providing and fixing Polyvinyl Chloride (PVC) pipes, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

50 mm nominal dia Pipes (10kg/cm2)

110 mm nominal dia Pipes (4kg/cm2)

90 mm nominal dia Pipes (4kg/cm2)