National Institute Of Technology Tender
Everything can be found here in your one-stop destination for all types of Kerala tenders online - be it Kerala PWD tenders or an LSGD Kerala tender. Search from across the categories, cities, and authorities while having the option to download tender-related documents. Also, get to know how to register as a bidder and how to bid online for Kerala tenders.
Costs
EMD
₹ 90,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2024_NITC_840580_1Tender No
Engg/D1/JE4/365/2024-25Tender Authority
National Institute Of Technology ViewPurchaser Address
-Website
http://eprocure.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
... More
REINFORCED CEMENT CONCRETE
-
-
-
... More
Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fllets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement:
-
-
-
... More
1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)
1
-
-
... More
Centering and shuttering including strutting, propping etc. and removal of form for
-
-
-
... More
Suspended floors, roofs, landings, balconies and access platform
10
-
-
... More
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.
-
-
-
... More
Thermo-Mechanically Treated bars of grade Fe-500D or more.
85
-
-
... More
MASONRY WORK
-
-
-
... More
Solid masonry with neatly dressed Precast solid block of size 40cmx20cmx15cm or nearest size for superstructure above plinth level up to floor two level including all cost of materials, labour charges etc.,
10.5
-
-
... More
CLADDING WORK
-
-
-
... More
WOOD AND P. V. C. WORK
-
-
-
... More
Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately).
-
-
-
... More
First quality irul wood
0.2
-
-
... More
Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately)
-
-
-
... More
First class teak wood
-
-
-
... More
35 mm thick shutters
2
-
-
... More
Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).
1
-
-
... More
Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :
-
-
-
... More
125x64x1.90 mm
2
-
-
... More
100X58X1.90 mm
2
-
-
... More
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :
-
-
-
... More
150x10 mm
1
-
-
... More
Providing and fixing bright finished brass handles with screws etc. complete:
-
-
-
... More
125 mm
1
-
-
... More
Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.
2
-
-
... More
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :
-
-
-
... More
200x10 mm
2
-
-
... More
150x10 mm
2
-
-
... More
Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.
-
-
-
... More
Single rubber stopper
2
-
-
... More
Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineer- in-charge.
2
-
-
... More
Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer-in-charge
-
-
-
... More
Extruded section profile size 42x50 mm
12
-
-
... More
Providing and fixing bright finished Stainless Steel Aldrop with necessary screws etc. complete :
-
-
-
... More
250x16x5 mm
2
-
-
... More
Providing and fixing metalic (SS 306,316 or equvalent) mosquito net of approved quality over aluminium frame work including cost and conveyance of all materialsand labour charges etc. complete but excludingcost of aluminium etc. complete
25
-
-
... More
STEEL WORK
-
-
-
... More
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.
-
-
-
... More
GI Tubular TATA or equvalent
3995
-
-
... More
FLOORING
-
-
-
... More
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.
-
-
-
... More
Size of Tile 600x600 mm
62
-
-
... More
Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete.
-
-
-
... More
Size of Tile 600x600 mm
50
-
-
... More
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
-
-
-
... More
Size of Tile 600x600 mm
9
-
-
... More
Providing and laying Matt/Antiskid Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).
-
-
-
... More
Size of Tile 600 x 600 mm
5
-
-
... More
ROOFING
-
-
-
... More
Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :
-
-
-
... More
12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks)
195
-
-
... More
Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineer- in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60
10
-
-
... More
Providing square type UPVC gutter with necessary clamps, bolts, nuts and specials such as nozzles sockets stoppers etc. including cost and conveyance of all materials and labour charges etc. complete as per the instructions of the dept. officers
-
-
-
... More
200mm or equivalent Square type UPVC
145
-
-
... More
Providing and fixing in roof with necessary self tapping screws sandwich panel Trafford roofing sheet with total thickness of 50mm with polyurethane foam of Density 36 Kg/cum plus or minus 2 Kg/cum with thermal conductivity with of less than or equal to 22 MW/MK and form tensile strength (adhesion) at 80C Greater than or equal to 80Kpa and youngs module at 80C greater than or equal to 2500 Kpa sandwiched between two GI sheets. The external and internal sheet shall have thickness of 0.40mm and 0.30mm respectively. The external and internal sheet shall be JSW/TATA/Bhushan /LLoyds make having a minimum 150 GSM galvalume coating pre-painted with approved colour and shade by the Engineer in charge with an SMP coating of 18 microns over epoxy coats of 7micorns
780
-
-
... More
Providing and fixing precoated galvanised iron (GI) sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :
-
-
-
... More
Ridges, hips or valley
44
-
-
... More
FINISHING
-
-
-
... More
12 mm cement plaster of mix :
-
-
-
... More
1:4 (1 cement: 4 fine sand)
80
-
-
... More
Finishing walls with Acrylic Smooth exterior paint of required shade :
-
-
-
... More
New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
85
-
-
... More
Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.
-
-
-
... More
On steel work
580
-
-
... More
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.
100
-
-
... More
Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.
-
-
-
... More
Two coats
2690
-
-
... More
Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound) content.
-
-
-
... More
With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre
3840
-
-
... More
Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :
-
-
-
... More
One or more coats on old work
125
-
-
... More
French spirit polishing :
-
-
-
... More
One or more coats on old work
5
-
-
... More
Finishing walls with Acrylic Smooth exterior paint of required shade :
-
-
-
... More
Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface
1150
-
-
... More
Dismantling and Demolishing
-
-
-
... More
Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge.
-
-
-
... More
Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)
10
-
-
... More
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead :
-
-
-
... More
Of area 3 sq. metres and below
1
-
-
... More
Of area beyond 3 sq. metres
1
-
-
... More
Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.
450
-
-
... More
Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:
-
-
-
... More
G.S. Sheet
1000
-
-
... More
Asbestos Cement sheet
300
-
-
... More
Dismantling water closet (Indian or European) of all types (C.I./PVC/Vitrious China) with foot rest, trap, etc including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.
2
-
-
... More
SANITARY INSTALLATIONS
-
-
-
... More
Providing and fixing water closet squatting pan (Indian type W.C.pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlle ddevice (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:
-
-
-
... More
White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests
1
-
-
... More
Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :
-
-
-
... More
W.C. pan with ISI marked white solid plastic seat and lid
1
-
-
... More
Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:
-
-
-
... More
White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap
2
-
-
... More
Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.
-
-
-
... More
10 litre capacity - White
1
-
-
... More
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard boardground fixed to wooden cleats with C.P. brass screws and washers complete.
2
-
-
... More
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.
-
-
-
... More
600 mm long towel rail with total length of 645 mm, width78 mm and effective height of 88 mm, weighing not less than 190 gms.
2
-
-
... More
WATER SUPPLY
-
-
-
... More
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
-
-
-
... More
15 mm nominal bore
2
-
-
... More
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931
-
-
-
... More
15mm nominal bore
1
-
-
... More
Providing and fixing Stainless Steel grating of approved quality and colour.
-
-
-
... More
Rectangular type with openable rectangular lid
-
-
-
... More
100 mm nominal size square
1
-
-
... More
Providing and fixing Polyvinyl Chloride (PVC) pipes, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall
-
-
-
... More
32 mm nominal dia Pipes (10kg/cm2)
5
-
-
... More
63 mm nominal dia pipe (6kg/cm2)
10
-
-
... More
110 mm nominal dia Pipes (4kg/cm2)
125
-
-
... More
25 mm nominal dia Pipes (10kg/cm2)
10
-
-
... More
Providing and fixing C.P. brass Health Fauset of approved quality conforming to IS:8931 :
-
-
-
... More
C P Brass Health Fauset
1
-
-
... More
ALUMINIUM WORK
-
-
-
... More
Providing and fxing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :
-
-
-
... More
For fixed portion
-
-
-
... More
Powder coated aluminium (minimum thickness of powder coating 50 micron)
72
-
-
... More
For shutters of doors, windows & ventilators including providing and fxing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)
-
-
-
... More
Powder coated aluminium (minimum thickness of powder coating 50 micron)
50
-
-
... More
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):
-
-
-
... More
With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)
10
-
-
... More
Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer- in-ch a rge
-
-
-
... More
Powder coated minimum thickness 50 micron aluminium
4
-
-
... More
Providing and fixing 4mm thick Aluminium Partition Panels, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.
-
-
-
... More
4 mm thick aluminium partion panels
10
-
-
... More
Providing and fixing sun control film on glass including cost and conveyance of all materials and labour charges etc. complete.
-
-
-
... More
White Sun Control film with 5% wastage
10
-
-
... More
WATER PROOFING
-
-
-
... More
Providing Fibre lamination works to the RCC structure using resine fibre glass and chemicals after washing the surface roughly cleaned and dry fill in the cracks with suitable putty, first apply the resine to the surface well spread and pressing, applying a second layer of resin to smooth finish for forming the whole to a solid mass including cost and conveyance of all materials and labour charges etc. complete as per the instructions of the dept. off icers
10
-
-
... More
Providing and laying water proofing treatment over the concrete surface by applying cement based two component polymer modified water proofing slurry coating coating (SIKA 109 TOP seal or equivalent) after cleaning the surface free from scale, rust, grease, oil etc. preparing the surface to be true and flat and saturated mixing the liquid (A) and powder (B) components in the ratio 1:4 by weight, applying in two coats with an interval of 2 to 6 hours for hardening in between and finally finished by rubbing down with a soft, dry sponge including protecting the applied surface from direct sunlight and storng wind and curing by gunny bags or polythene sheeting upto 5 days etc. complete.
112
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements
Past BiddersThis list is curated from the bidders of the similar tenders in the past
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%
- Bidder NameThis Information is for unsubscribed user This Information is for unsubscribed user
- Awarded Ratexx%