National Institute Of Technology Tender

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing ISI : 12817 marked stainless steel butt hinges of size 125x64x1.90 mmwith stainless steel screws etc. complete :

Providing and fixing IS : 12817 marked stainless steel butt hinges of size 100X58X1.90 mm with stainless steel screws etc. complete :

Providing and fixing IS : 12817 marked stainless steel butt hinges of size 100X58X1.90 mm with stainless steel screws etc. complete :

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm

Providing and fixing 150x10 mm bright finished stainless steel tower bolts with necessary screws etc. complete :

Providing and fixing 300mm x 16mm C.P steel aldrop with necessary fittings (best approved quality) including cost and conveyance of all materials and labour charges etc. complete.

Providing and fixing 300mm x 16mm C.P steel aldrop with necessary fittings (best approved quality) including cost and conveyance of all materials and labour charges etc. complete.

Providing and fixing bright finished brass handles 125 mm with screws etc. complete:

Providing and fixing Single aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing double strip magnetic catcher (horizontal type)high quality ISI marked of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete.

Providing and fixing powder coated heavy duty telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer-in charge.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections profile size 42x50 mmhaving an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer specification and direction of Engineer- in-charge

Providing and fixing 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of H section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. U cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete with all necessar

Reixing dismantled plywood of size above 10mm to 25mm after necessary repair works for cupboards, shelves, partition, drawers, table top etc. including necessary screws etc. complete.

Providing and fixing 20 mm thick marine plywood or gurjan confirming to IS:710 for cupboards, shelves, partition, drawers, table top etc. including necessary screws etc. complete.

Providing and fixing bright /matt finished 125 mm Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Providing and fixing bright /matt finished 100 mm Stainless Steel handles of approved quality & make with necessary screws etc all complete.

Plastering with C.M. 1:4 (one cement four sand), 12mm thick for walls inside and outside with necessary scaffolding and thread lines, including cost and conveyance of all materials and labour charges etc. complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Painting with two or more coats synthetic enamel paint using brush/roller on new work of approved brand and manufacture to give an even shade :

Providing and applying best quality wood putty of approved brand and manufacturer, including cost for thinner, over wood surface to prepare the surface even and smooth complete

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour: One coat

Wall painting with two coat premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre asper instruction of engineer in charge

Painting with synthetic enamel paint one or more coats on old work of approved brand and manufacture of required colour to give an even shade

Dismantling doors, windows and clerestory windows (PVC or Plywood) shutter and frames of area 3 sq. metres and below including chowkhats, architrave, holdfasts etc. complete and stacking serviceable material in Engineering Unit store and other materials within 50 metres lead as per the instructions of Engineer-in-Charge

Dismantling wooden boardings of thickness above 10 mm up to 25m min lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Providing and fixing 600mm SS towel rail inside walldrobe complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour