National Institute Of Fisheries Post Harvest Technology And Training Tender

Providing and fixing 125 mm aluminium handles, ISI marked, anodised transparent or dyed to required colour or shade, with necessary SS screws etc. Complete

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 100 M.

Wall painting with acrylic emulsion paint two coats, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour on walls.

Providing and laying in position cement concrete of specified grade 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) excluding the cost of centering and shuttering - All work up to plinth level

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in Cement Mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level with Cement mortar 1:4 (1 cement :4 coarse sand).

Providing and fixing to existing door frames 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Providing and fixing 250x16 mm aluminium sliding door bolts, ISI marked anodised, transparent or dyed to required colour or shade, with SS nuts and screws etc. Complete

12 mm cement plaster of mix 1:6 (1 cement: 6 fine sand) on walls

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under,with cement mortar 1: 4 ( 1 cement : 4 fine sand) including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 100 metres lead.

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension of 48 x 40 mm (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Department

Centering and shuttering including strutting, propping etc. and removal of form work for plinth protection