Local Self Government Department Tender

od980300/2020_2021 : DRY RUBBLE MASONRY _ Dry rubble without concrete leveling course masonry with good quality blasted rubble<br>including packing to compactness to lines and levels cost and conveyance of all materials labor charges etc. complete as per<br>direction of Departmental officers at site.

12.7 : Supplying, fitting and placing TMT bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

od849763/2020_2021 : Providing concrete for plain concrete in TOP Belt concrete in DR Retaining Walls complete as per drawings and direction of Engineer-in-Charge.<br>P.C.C grade M 10, Nominal mix 1:3:6

Irish Drain-CH 0/000 to 0/150

od849748/2020_2021 : Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m

od849754/2020_2021 : Construction of Plain Cement Concrete Pavement (WITHOUT FORM WORK) : Mord Item 6.4 Modified<br>Construction of Plain Cement Concrete Pavement, thickness as per design,over a prepared sub base, with 43 grade cement or any other type as per clause 1501.2.2 (M 20 grade), coarse and fine aggregates conforming to IS 383 (maximum size of coarse aggregate not exceeding 25 mm) mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side form work (steel channel, wedges,steel plates including leveling the form work as per drawing), spreading the concrete with shovels, rakes, compacted using needle vibrators and finished in continuous operation including provision of contraction and expansion construction joints, curing of concrete slabs for 14 days, with water finishing to lines and grade as per drawing and Technical Specifications clause 1501

RETARRING-CH 0/000 to 0/700

3.5.3 : Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 mExcavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3

4.9 : Wet Mix Macadam br Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. br By Mechanical Means with 1 km lead

75.5.5.A.1pb : Modified Penetration Macadam 50 mm thick using Bitumen S-65 - Packed Bitumen Rates br Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506.

75.5.1.1pb : Prime Coat - Low porosity - With Packed Bitumen Rates br Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

75.5.2.3pb : Tack Coat - With Packed Bitumen Rates br Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.2.1pb : Tack Coat - With Packed Bitumen Rates br Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.5.9.1.2pb : 20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder - Bitumen S-65 - Packed Bitumen Ratesbr Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. br Case - I By Manual Means br (II) Bitumen (S-65)

75.5.12.A.1.2pb : Seal Coat - Manual Means - Type A - Bitumen S-65 - Packed Bitumen Ratesbr Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 br A. By Manual Means br Case I : Type A br (II) Bitumen (S-65)

od904703/2020_2021 : Providing and fixing NAME BOARD fixed over MS sheeting, 2 mm thick supported on GI pipe 50 mm dia<br>firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete<br>450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification<br>Clause 1701.<br>600 mm x 450 mm Rectangular