Local Self Government Department Tender

5.1.1a : Prime Coat :- Low porosity br Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

5.2.3a : Tack Coat brProviding and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

5.5.B.2a : Modified Penetration Macadam 75 mm thick using Bitumen S-65 br Construction of penetration macadam over prepared base by providing a layer of compacted crushed coarse aggregate using chips spreader with alternate applications of bituminous binder and key aggregates and rolling with a three wheel 80-100 kN static roller to achieve the desired degree of compaction as per Technical Specification Clause 506. br (B) 75 mm thick :- (II) Bitumen (S-65)

5.2.1a : Tack Coatbr Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

75.9.3.pa : Plastic Roads - Bitumen S-65 brbrPlastic roads- Bulk Bitumen Rate brbr20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder -brbrBitumen S-65 - Bulk Bitumen and Shredded Plasticbr br brbrProviding, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, using HM Plant attached with open pugmilll.Heating of aggregate at 150 degree Celsius to 170 degree Celsius, then transferring the hot aggregate to pugmill and add shredded plastic @10.22 kg/100m2 mixing well to form a uniforth thin layer of plastic Over-hot aggregate and adding hot bitumen (150 to 165 degree Celsius) @ 13.578 Kg/10m2 and mix well, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508 br brCase - I By Manual Means br brbr(II) Bi umen (5-65)

5.12.A.3.2a : Seal Coat - Manual Means - Type C - Bitumen S-65 br Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 br A. By Manual Means :- Case - III : Type C br (II) Bitumen (S-65)

od1204296/2021_2022 : Surface dressing of the ground including removing vegetation and in-equalities not<br>exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.<br>All kinds of soil

75.8.1.1.A : Providing Plain cement concrete for wearing coat CC 1:2:4 (1 cement: 2 fine aggregate:4 course aggregate) laid to required slope as required including compaction, finishingand tamping etc .complete. Max. size of course aggregate not exceeding 25mm , mixedin concrete mixer etc complete as per specification (i) Nominal mix (1:2:4)

od1204295/2021_2022 : :Supplying and Fixing Information board 75x60 cm using GI pipes as post and MS<br>sheet surrounded by MS angles including painting, lettering and fixing in position as per direction of e-i--c.