KITCO Limited Tender

od330673/2022_2023 : Disconnecting and taking out existing exhaust fan with due care and handing over to client after cleaning for overhauling and taking back from client and painting and fixing back the existing industrial type exhaust fans including arrangement and providing for proper aluminum louvers (including cost of louvers) so as to prevent birds /rain water entry to inside of the press- with all accessories including all electrical connections without damaging the fan and stacking of unserviceable materials within factory premises as per direction of Engineer - in-Charge and commissioning to ensure the fans are working properly.

od26050/2022_2023 : Supply & fixing stainless steel wind driven turbo ventilator 610 mm or nearest size throat diameter with FRP/Aluminium or approved base material to match the roofing sheet profile and variable angle elbow, UV stabilised powder coating, including all fixing accessories ,making good and watertight the roof, all materials, labour charges, lead, lift at all levels etc complete as directed by the Engineer- in-Charge

od26183/2022_2023 : Fixing departmentally supplied turbo ventilator on new roofing sheet with necessary frame work , all accessories for fixing the same including the cost of cutting and making water tight the roofing sheet, all materials, labour charges, lead, lift at all levels as per the direction of Engineer - in-Charge.

od362179/2021_2022 : Supplying ,fixing and making water tight, the glass panes on the existing aluminium/MS frames using Neoprene / EPDM rubber gasket : etc as required <br>Float glass panes of thickness 8 mm

od362310/2021_2022 : Cleaning the existing steel members of truss, purlin etc including removing rust by scrapping ,buffing and sand papering and preparing the steel surface smooth complete as directed by the Engineer in charge.

od329818/2022_2023 : Painting with ready mixed aluminium primer of approved brand and manufacture on steel work

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

13.100.1 : Painting with aluminium paint of approved brand and manufacture to give an even shade:One or more coats on old work

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.63.1 : Painting with aluminium paint of approved brand and manufacture to give an even shade.Two or more coats on new work

od26234/2022_2023 : Providing and fixing profiles single sheet with one side crimped made out of 0.50mm TCT,550 Mpa colour coated sheet with 150GSM Zinc Aluminium alloy coating mass (55% Aluminium, 43.5% Zinc and 1.5% Silicon) total of both sides. Single sheet without joints to be provided along the slope.The colour coating shall have a total coating thickness of 35 micron silicon modified polyester paint system of approved colour comprising of 20 microns of exterior coat on top surface and 5 microns reverse coat on back surface over 5 micron primer coat on both surface. Roof sheet shall be fixed on the purlin with SDST screws. All the joints will be sealed with sealant and stitched with stitching screws where ever necessary. 'Minimum sheet overlap at end laps shall be 150mm. Penetration and end laps in sheet shall be sealed by using proper sealant. 'Profiled HDPE fillers shall be provided wherever required to close voids between capings and troughs of the sheet to provide a 'weather tight exterior. Rate shall include cost and conveyence of all materials, lead, lift, scaffolding, all labour charges, making the roof water tight with required sealent etc complete at all level and as directed by Engineer-in-Charge.(Curved area including crimping shall be measured for payment)

od108582/2023_2024 : Providing and fixing Double skin system both top layer of kliplok and plain sheet at bottom layer with Insulation (TYPE) having external shall be made of (Steel base metal thickness) 0.45mm BMT (0.50mm TCT excluding paint), (Steel Grade) G550 (min 550 yield strength), (sheet cover width) 700mm effective cover width with five major corrugation, (profile Rib height) 43mm high rib spaced at (Rib Pitch) 233mm c/c with micro stiffener (profile characteristic) (Make) Kliplok 700equivalent. The base steel sheet shall be coated with (Type of metal ccating & its alloy composition) zinc-aluminium alloy Zincalume (i.e. 55% Al, 43.4% Zinc, 1.6% Si), class AZ150- (coating mass) minimum of 150 g/m² coating total on both sides, pre-painted with (Paint system - Resin and pigments used) exterior quality XRW paint system of Super Durable Polyester resin with stable inorganic pigment with no lead contents for colour durability, high solar reflectance Index (SRI) - (Green credentials - SRI value) Thermatech technology for cool comfort, of Colorbond XRW steel or equivalent shall conforms to general requirement (complying Standards) of IS 15965 class 3/ AS/NZS 2728 type 4 (corrosion class) durability value of (Make) Tata BlueScope Steel make or equivalent. The sheet shall be free from defects and have (branding for easy identification) brand marking of the manufacturer giving product details on the back of the sheet at regular interval confirming genuinity of the material.<br><br>The steel sheet shall be (Fasteners class and quality) fastened with min 25µm mechanically plated zinc-tin alloy coated, hex head, self-drilling screw, with EPDM washer (Make) Roofix/Buildex equivalent conforms to AS 3566 Class-3 (complying standard and corrosion class). In-between the two sheets, 50mm (insulation specification) thick, density 48kg/m3 Rockwool with or without facing as per design requirement complying with IS 8183 BS-3958 Part-5. ASTM C592-80 approved by engineer in-charge."<br> (All works covered by this specification shall be carried by an experienced agency having sufficient experience<br>in this type of roofing system Only skilled and experienced persons shall be employed for this purpose.)

od27872/2022_2023 : Providing and fixing cladding in required width with plain galvalume colour coated sheet made out of 0.5mm TCT, minimum 550 MPa cold rolled steel with hot dip metallic coating of Aluminium Zinc alloy (Galvalume) 150 gms/sqm,total of both sides, AZ 150 as per ASTM A 792 or AS1397, with polyester colour coating including cost and conveyance of all materials, scaffolding, lead, lift, labour charges, etc. complete at all levels as directed by Engineer-in-Charge

od26271/2022_2023 : Providing and fixing aluminium gutter of approved pattern & design, made out of machine cut aluminium sheet and machine folded , including providing aluminium Screws and washers of approved size in specific pattern and interval including drilling holes in the receiving surface and providing expandable plastic sleeves in holes, providing Lap joints and applying sealant ,including providing nozzles etc to connect to the down water pipes ,complete as per drawing and direction of Engineer -in-charge.<br>Anodised aluminium sheet 2 mm thick (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

od362455/2021_2022 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes,fittings & specials with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 160 mm dia 4 Kgf/cm2 - Internal work- Exposed on wall

od333863/2022_2023 : Supplying, laying, jointing and hydrostatically testing ISI marked HDPE pipes of 160mm<br>dia conforming to as per IS 4984,1985 PE-100 including all fittings and specials such as tees, elbows,Mitre bends,<br>reducers, end caps, saddles, plugs,coupling, MTA , all types of pipe supports etc.including cost of all<br>jointing materials, bolts, nuts, rubber washers, ferrule, pipe supports, hire of tools, cost for conveyance of water for testing, etc. complete so as to withstand the internal design pressure of 4 kg/cm2 for external<br>works

12.44 : Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

14.72 : Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required location with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in Charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note:- This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done .

od135004/2023_2024 : Disconnecting and taking out existing exhaust fan with due care and handing over to client after cleaning for overhauling without damaging the fan and stacking of unserviceable materials within factory premises as per direction of Engineer - in-Charge and commissioning to ensure the fans are working properly.

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

od28898/2024_2025 : Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer - in-charge. (Note :- Minimum Cement content considered in this item is @ 330 kg/cum. Additional cement requirement as per mix design shall be considered by the bidder while quoting, nothing extra shall be paid on this account)All work above plinth level upto floor V level

12.52.3 : Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge.12.5 mm thick square edge PVC Laminated Gypsum Tile size 595x595 mm made of Gypsum plasterboard , manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16 mm thick fire retardant PVC film on the face side and 12 micron metalized polyster on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyster film so as to make the tile a completely sealed unit.