Kerala Water Authority Tender

100.41.39:Supply, stacking, spreading and consolidating of Quarry Muck in the trench of pipe line, including carriage, loading, unloading & stacking up to any lead.

4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.22.1:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelMild steel and Medium Tensile steel bars

50.6.1.7:Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15 cm in : CM 1:6 ( 1 cement : 6 coarse sand ) etc complete

50.6.2.1:Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

50.2.25.1:Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge

4.1.6:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

12.1.3:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/m2

13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand)

9.95.3:Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:100x75x4 mm

9.97.3:Providing and fixing aluminium tower bolts, ISI marked, anodised(anodic coating not less than grade AC 10 as per : 1868), transparent or dyed to required colour or shade, with necessary screws complete:200x10 mm

50.9.15.1:Supplying and fixing 200 mm Aluminium aldrop

APPENDIX A - PART II :- CONSTRUCTION OF PUMP HOUSE - ELECTRIFICATION WORK.

OD64831/2023-2024:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface I recessed mediumclass PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper Group B conductor single core cable etc. as required

OD64832/2023-2024:Providing and fixing following capacity TP&N disconnector fuse switch unit inside the existing panel board with lSI marked HRC fuses including drilling holes in cubiclepanel, making connections, etc. as required. 63ATP&N

OD64833/2023-2024:Earthing with G.l. earth pipe 4.5 meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate Jlaving locking arrangement and watering pipe etc. with charcoal/coke and salt as required

OD64834/2023-2024:Installation, testing and commissioning of pre-wired, fluorescent fitting I compact fluorescent fitting of all types, complete with all accessories and tube/lamp etc.directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required

OD64835/2023-2024:Supplying fluorescent lamp set 36/40 W with all accessories

OD64836/2023-2024:Supplying and fixing metal box of 200 mm X 125 mm X 60 mm size (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

OD64837/2023-2024:Supplying and providing meter box and panel board for KSEB supply and providing necessary fuse unit and isolators for 3 phase supply as per the direction of departmental officers.

APPENDIX B - PART I :-LAYING PUMPING MAIN - WORKING CHARGES.

15.43.2:Dismantling manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in-Charge:Bituminous road

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

100.8.1:Fencing one side of trenches, 1.50m height with two rows of 10cm plastic caution tape in vertical casuarina pole (girth 15cm to 24cm) fixed at 2m intervals.

100.98.1008:Engaging Coolie.

100.9.9:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 110 mm nominal outside diameter pipes.

OD73060/2023-2024::Supplying 110 mm PVC Tee (10 kg/cm2)

100.12.9:Conveying and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc., but excluding cost of pipes and fittings for External work: 100mm diameter nominal bore.

100.37.5.2:Fabricating M.S. flanges of diameter 100mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.4:Welding 100mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

100.37.5.5:Grinding cut and weld edges of 100mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates.

OD70037/2023-2024: Providing MS clamps for holding pipes in the bridge portion using ISA 50x50x6mm MS angles by fabrication work for holding pipe in the bridge portion by fixing clamps with handrails of bridge including cost and conveyance of angles .MS round bars ,nut & bolts e.t.c and all fabrication charges ,finishing with priming coat and anti corrosive paint coat and all labor charges for fixing MS clamps in the rail of bridge e.t.c. complete as per direction of departmental officers

OD64827/2023-2024:Interconnecting/Jointing t he newly laid 110mm PVC line to the existing 75/90/110mm PVC line by cutting the existing line diametrically,the cut being perpendicular to the axis of the pipe and smoothening the cut ends and inserting the suitable PVC TEE and reducer, supplied by the contractor and placing in position , jointing with solvent cement and testing to the required test pressure including cost of all specials,all labour charges etc complete as per direction of departmental officers.

OD69077/2023-2024:Jointing the newly laid 110 mm PVC pipe with newly laid 100 mm exposed GI pipe line for connecting the bridge portion, using necessary specials such as reducers, adaptor, PVC and GI bend and making the joint water tight, all labour charges, cost and conveyance of all specials etc. complete as per the direction of engineer in charge.

100.31.1.2:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 100mm diameter, Class I.

OD69078/2023-2024:Constructing valve chamber of inner size 1.0 m x 1.0 m x 1.5 m in M-25 grade cement concrete for reinforced cement concrete work and 10 mm MS rod(115 Kg) for Base slab & side wall and 12 mm MS rod (102 Kg) for cover slab.(Base slab 1.3 mx1.3 mx0.15 m,side wall 15 cm thick,cover slab 3 Nos of size 1.3 mx0.0.42 m x 0.15 m)over a PCC base of size 1.5 mx1.5 mx0.10 m in 1:3:6 using 40 mm broken stone,plastering inside the valve chamber and cover slab in CM.1:3, 6 mm thick including cost and conveyance of all materials etc.complete. as per the direction of deptl officers.

4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

100.39.5:Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work: 150mm diameter pipe.

APPENDIX B - PART II :-LAYING PUMPING MAIN - COST OF MATERIALS

100.98.237:Supply of PVC Pipe, 10kg/cm2, 110mm Dia.

OD72301/2023-2024:Supplying 100 mm GI Class B pipe (weight not less than 8.5 Kg/M) having relevant IS standards applicable

100.98.482:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Hand Wheel PN 1.6, Size 100mm.

OD64830/2023-2024:Cost of 80mm GI bend

OD69398/2023-2024:Supplying 110mm pvc bend(10kg/cm2)(EXCLUDING GST)

APPENDIX C :-SUPPLY, ERECTION AND COMMISSIONING OF SUBMERSIBLE PUMP SET

OD64819/2023-2024:Supply, erection. testing and commissioning of electrically operated brand new 12.5 HP submersible pump set of reputed manufacturers having ISI mark suitable for 150/200 mm dia, Tube well capable to discharge of water 350-400 LPM against a head of 80-100 M with stainless steel shaft with bronze impeller coupled with suitable three phase 400/440V prime over with a delivery size of 80 mm including supplying 3 X 6 mm square submersible flat type copper cable not less than 10 M, fully automatic star delta starter, wall mounted type panel board consisting of 63 A main switch, 63 A changeover switch, 63 A ELCB/MCB, single phase preventer, voltmeter, ammeter with selector switch, capacitor (6 KVAR) and earthling materials etc. and pressure gauge. 80 mm GI pipe (heavy duty) with couplings / flanges as column pipe - 10.00 M including its fabrication works for delivery connection, 80 mm CI sluice valve with wheel (PN 1.60) - 1 No, 80mm GM valve- 1No, 80mm CI NR valve (PN 1.60) -1 No, earth connection as per IE rules etc., erection and trial running etc. complete including one year Warrantee period as per direction of engineer in charge

OD64820/2023-2024:Supplying 80 mm GI Class B pipe (weight not less than 8.5 Kg/m) having ISI mark

OD64821/2023-2024:Supplying good quality 80mm GI BEND

OD64822/2023-2024:Supplying 80mm GI Tee

OD64823/2023-2024:Supplying 3X4mm sq. submersible cable having ISI mark

OD64824/2023-2024:Supplying, conveying and fitting automatic module for mobile starter (make L&T, model M power pro) for automatic operation of pump set including cost and conveyance of all components and erection charges etc complete as per the direction of engineer in charge.

OD64825/2023-2024:Providing bleaching powder solution feeding unit for disinfection of water consisting of supplying and providing polyethylene water storage tank (ISI marked) with cover and suitable locking arrangement of capacity 500 Ltr, providing platform of size 1.25 M x 1.00 M for placing PVC tank by structural steel work riveted, bolted or welded in built up sections including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using ISA 75 x 75 x 6, providing 20 mm CPVC pipe connection for inlet water supply to tank from pumping main and out let supply from tank to bottom of tube well including providing two number ball valves in inlet line and one valve in outlet line and providing 50 mm CPVC pipe darin outlet in tank for scovring arrangement including providing 50 mm PVC ball, valve in drain pipe and making the unit functional for collecting water from pumping main and continuous feeding of bleaching powder solution to tube well etc complete including cost and conveyance of polyethylene water storage tank (ISI marked) with cover and suitable locking arrangement of capacity 500 Ltr - 1 No, Steel structural platform using ISA 75 x 75 x 6 - 108 Kg, inlet and outlet pipe connection using 20 mm CPVC pipe and specials - 66 M and valves, drain arrangement all labour charges, supplying 30/40 Ltr PVC bucket - 2 Nos and PVC mug - 2 Nos (for mixing bleaching powder), hire charges of tools etc complete as per the direction of engineer in charge.

OD72450/2023-2024: Supply and fixing of 63A 4pole change over switch

OD72451/2023-2024:Supply and fixing of 63A TPN Main switch

OD72481/2023-2024: Supply and fixing 63A fuse unit