Kerala Veterinary And Animal Sciences University Tender

od235941/2023_2024 : Supply, erection, testing and commissioning of 4 pole structure -175 x 85 mm RSJ pole Including taking pits for laying 11 meter A pole structure(4 Nos) with standard clearance and concreting the same with out damages to A poles."

od235942/2023_2024 : Supply, erection, testing and commissioning of superior 11kV LA (1 Set =3 Nos) with all accessories including nuts, bolts for fixing on the HT side 4 pole structure with standard clearance from AB switch, DO fuse etc

od235944/2023_2024 : Supply, erection, testing and commissioning of 11kV 200A DO Fuse (1Set = 3 Nos)unit complete with all accessories inducing nuts bolts for fixing (1 Set =3 Nos) on the HT side 4 pole structure with standard clearance from AB switch, DO fuse etc

od235946/2023_2024 : Supply, erection, testing and commissioning of 11 kV 400A gang operated AB Switch (1Set = 3 Nos) with down rod and operating handle unit complete with all accessories inducing nuts bolts for fixing on the HT side 4 pole structure with standard clearance from AB switch, DO fuse etc.

od235948/2023_2024 : Supply, erection, testing and commissioning of 11kV Disc(1 set=3 Nos) complete with all accessories for drawing supply from KSEB side.

od235949/2023_2024 : Supply, erection, testing and commissioning of 11kV pin insulator with all accessories on the HT side 4 pole structure with standard clearance from other equipments for fixing and drawing conductor.

od235951/2023_2024 : Supply at site installation, testing and commissioning of TOD meter for KSEB as per KSEB specifications, all prewired from CT and PT etc including supply and fixing of TOD meter testing of meter and CT/PT at TMR division of KSEB (Including charges for transporting to and fro, and testing, HT TOD meter and CT PT unit from testing centres) with necessary armoured control cables etc. complete as per KSEB/ Inspectorate recommendations - 0.2s class HT TOD Meter 4 wire with Meter Kiosk and TTB.

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.17.24 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.6 x 4 sq. mm

od268619/2023_2024 : Supply fabricate and install ladder tray 20cm wide, 3m long with MS angle<br>30x30x3mm & flat 20x3 mm at 20cm spacing (tray to be 30cm above ground)<br>including MS clamps for cable

od268620/2023_2024 : Supply and doing additional Bolt, Nut and washers of required size

od235954/2023_2024 : Supply, erection, testing and commissioning of Racoon conductor - For drawing distribution of power to main bus and interconnection between equipments.

od241230/2023_2024 : Supply and doing No:"0" SWG Copper wire for jumper connections

od235956/2023_2024 : Supply, erection, testing and commissioning of combined CT(15/5A, CL:0.2s,15VA) - PT (11000/110V, 100 VA, CL:0.2) outdoor unit for metering with all accessories.

od235959/2023_2024 : Supply, erection and fixing painted of Cross arm GI Channel 3.15 m for fixing AB switch, DO Fuse, LA and CT-PT units etc complete

HT Cable laying and terminations

od241936/2023_2024 : Supplying of Unearthed/earthed armoured, aluminium<br>conductor XLPE power cable of 11 KV grade confirming<br>to IS 7098 (Part II) amended upto date as per the<br>following size:

8.1.2 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 120 sq. mm and upto 400 sq. mm

10.4.3 : Supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required:240 sq. mm

10.5.3 : Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required :240 sq. mm

Civil works required for Transformer Plinth, Meter kiosk plinth, Metal spreading, Yard fencing etc

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

50.2.26.1 : Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

16.3.3 : Supplying and stacking at site.53 mm to 22.4 mm size stone aggregate

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

4.1.3 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

10.2 : Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

13.33.1 : Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing

16.70.2 : Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts , bolts and washers as required complete as per the direction of Engineer-in- charge.Made of G.I wire of dia 4 mm. PVC coated to achieve outer dia. not less than 5 mm in required colour and shade

13.61.1 : Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

Earthing

5.2 : Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

5.6 : Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

5.8 : Supplying and laying 25 mm X 5 mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)

od241633/2023_2024 : Providing and fixing 25 mm X 5 mm copper strip in 40mm dia G.I. pipe from earth electrode includingconnection with brass nut, bolt, spring, washer excavation and re-filling etc. as required. Riveting sweating & soldering of copper strip with another<br>copper strip or any other metallic object as required.

5.14 : Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

90.16.1.1 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.00 mm copper conductor ( 14 SWG)

90.16.1.2 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required2.65 mm copper conductor (12 SWG)

90.16.1.3 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10 SWG)

90.16.5.1 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.00 mm (14 SWG)

90.16.5.2 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.2.65 mm (12 SWG)

90.16.5.3 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.3.15 mm (10 SWG)

90.16.5.4 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

90.16.5.5 : Supply of superior quality copper earth socket for the following size of earth conductor including crimping etc. as required.4.75 mm (6 SWG)

od241866/2023_2024 : Supply and laying bare earthing conductors of the following sizes laid 0.6 m below ground level including excavating trench of suitable size and refilling etc. as required (in ordinary soil).4mm

od235940/2023_2024 : Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required. copper conductor (6 SWG)

MV Cable laying and terminations

od242627/2023_2024 : Supplying of Unearthed/earthed armoured, aluminium conductor XLPE power cable of 1.1 KV grade confirming to IS 7098 (Part II) amended upto date as per the following size: 3.5Cx300 sq mm

od242643/2023_2024 : Supplying of Unearthed/earthed armoured, aluminium conductor XLPE power cable of 1.1 KV grade confirming to IS 7098 (Part II) amended upto date as per the following size: 3.5CX240 sq mm

7.1.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Above 185 sq. mm and upto 400 sq. mm

7.6.4 : Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above 185 sq. mm and upto 400 sq. mm

7.8.4 : Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required.Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

9.2.27 : Supplying and making outdoor end termination with cast resin compound including aluminium lugs and other jointing materials for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2 X 300 sq. mm

Safety Equipment/MISC. Items

od242747/2023_2024 : Supply and fixing CO2 type fire extinguisher conforming to IS 2876 with cylinder duly charged of capacity 4.5 kgs including fixing clamps brackets, bolts and nuts etc. as<br>required.

od243530/2023_2024 : Supplying of fire buckets of 9 litres capacity quality painted white from inside and red from outside and having inscription “FIRE” in white conforming to IS2546-1974 duly amended upto date as required. (Set of four)

od243915/2023_2024 : Supplying of first aid box with cover made out of 16 SWG MS sheet of size 450 mm x600 mm x 200 mm and painted with two coats of enamel paint over one coat of steel primer and having inscription “FIRST AID BOX” in white and a red cross of suitable size with following items:<br>conforming to IS 2217 : 1963.<br>- 1 No. band-aid bandage 150mm<br>- 1 No. Savlon/dettol liquid soap 100 ml<br>- 1 No. Bottle betadine 30 ml<br>- 1 No. Roll cotton<br>- 1 No. Packet dressing material

od246418/2023_2024 : Providing of rubber mat 1 mtr. wide and 12 mm thick to withstand 3.3 KV dielectric strength as per IS 5424 : 1969

od246420/2023_2024 : Providing & fixing danger plates made of mild steel at least 2 mm thick & vitreous enameled white on both sides & with inscriptions in signal red colour on front side as read. (hindi&eNGLISH)<br>(a) High Voltage – size 250 mm x 200 mm<br>(b) Medium Voltage – size 200 mm x 150 mm

od246421/2023_2024 : Supply & fixing shock treatment chart duly mounted on a wooden frame with 5 mm thick glass as reqd.<br>(approximate front area 1.20 sq. metre)

od268623/2023_2024 : Supplying & fixing of laminated schematic drawing

od268624/2023_2024 : Supply and fix labels for panels switches,cables etc as insisted by the inspectorate

od268625/2023_2024 : Supply of 1 set of 11kV hand gloves of ISI Grade

4.1.7 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.600 mm width X 50 mm depth X 2.0 mm thickness

Panel boards and accessories

od246436/2023_2024 : Supply, installation, Testing and Commissioning of dust, damp and vermin proof free floor mounted, Indoor type factory built sheet steel enclosed modular construction(each bay shall be modular and shall be bolted together to form the panel board) extendable compartmentalized cubicle panel board, suitable for operation on 415 ±10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized structural sections and covered with CRCA sheet steel /GI sheet of 2mm thick for framework and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade (or other approved superior process), complete with Aluminium bus bars, inter-connection with copper conductor wires / aluminium strips, neutral links, earth bus etc. including control wiring with 1.5sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor single core cable for voltage & current respectively, cable alleys, cable gland plates in two half etc. necessary metering protections & indications and mounted with the following switch gears etc. complete as required. The panel board shall be IEC- 61439- Part-1 & 2 compliant and of form-4b construction.<br>(Each MCCB will have variable current setting for over current and short circuit, pad lockable in off position, indication light for ON, shrouding on incomer side, termination shall be suitable for aluminium bus bars. Current density of aluminium busbars shall not be more than 0.80 A per sq.mm.)<br>Incomer:<br><br>630 Amps, 36KA (ics = 100% icu ), 415 Volts, 50Hz, 4 pole MCCB with microprocessor based having isolation duty and 3O/C & 1E/F releases , extended rotary handle etc. set at 80% with in built earth fault release .<br>(a) Meters & Relays:<br>Multifunction Energy meter with display of voltage, Current, Power, Frequency, Power Factor & THD(eq to EM 6400 of Schneider make), with communication port , necessary CTs and protection Switchgears-1 set<br>(b) RYB indication lamp LED type with protection gears- 1 set.<br>630 Amps FP ON-LOAD CANGEOVER SWITCH-1No.<br>Outgoing:-<br>250A FP MCCB, 25kA-1No.<br>200A FP MCCB, 25kA-1No.<br>125A FP MCCB, 25kA-1No.<br>100A FP MCCB, 25kA-3Nos<br>63A FP MCCB, 25kA-1No<br>63A TPN ISO.-1no<br><br>All MCCB's should be with, Rotary operated handle and all necessary accessories.<br>Busbar:1 Set TPN AL bus bars suitably rated for 630A.

od246440/2023_2024 : Supplying, installation, testing & commissioning of factory built floor mounted auto-manual power factor correction system panel of 90 KVAR capacity having 3 phase, Mixed Dielectric / APP / MPP / utra heavy duty type (total power loss not exceeding 0.35 W/ KVAR) power capacitor in eight steps. The APFC panel shall be complying to IEC 61439 & IEC 61921. The front side switchgear section shall be compartmentalized.<br>The panel shall be fabricated in compartmentalized design from CRCA sheet steel of 2mm thick for frame work and covers, having 300 Amp capacity extensible type TPN Aluminium Alloy bus bars of high conductivity, DMC/ SMC bus bar supports, with short circuit withstand capacity of 35 MVA for I Sec., bottom base channel of MS section not less than 100mm x 50mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common GI earth bar of suitable size at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears / accessories with required size of Al. bus bars and control wiring with 1.5 / 2.5 sq.mm. PVC insulated FRLS copper conductor Single Core cable, provided with exhaust fans (with thermostat) and grills for proper ventilation, interconnections with suitable size conductor cables & lugs and accommodating the following swicthgears & accessories:<br>a) 200Amps, 415V, 4P, 36 KA MCCB (Ics = 100% Icu) with microprocessor Based over current, short circuit Release, extended rotary handle etc -1 No.<br>b) LED Indicating lamp with holder for all steps (ON indication) and mains indication -1set<br>c) One numbers dual source, dual setting, binary type automatic power factor sensing and correction relay (8 stages) complete with RS 485 module, all associated accessories etc. as required. - 1 Set<br>BUS-BAR<br>TPN Aluminium bus bars of 300Amps capacity with heat shrinkable coloured sleeves, DMC /SMC bus bar supports at required intervals complete for cross section, size supports and their spacing etc., for with standing fault level of 31 MVA for 1 sec.<br>OUTGOINGS.<br>a) 100A TPN SFU with 63A HRC + 25KVAR Capacitor 480V + Capacitor duty contactor for 25KVAR + 7% detuned reactor for 20KVAR 440V– 2 sets.<br>b) 63A TPN SFU with 50A HRC + 20KVAR Capacitor 480V + Capacitor duty contactor for 20KVAR + 7% detuned reactor for 15KVAR 440V– 2 sets.<br>c) 63A TPN SFU with 32A HRC + 15KVAR Capacitor 480V + Capacitor duty contactor for 15KVAR + 7% detuned reactor for 10KVAR 440V – 1 set<br>d)32A TPN SFU with 20A HRC + 10KVAR Capacitor 480V + Capacitor duty contactor for 10KVAR + 7% detuned reactor for 5KVAR 440V – 2 set<br>e) 7% detuned harmonics filter consisting of 7% Detuned Copper Reactors, Capacitors shall be minimum 525V, Ultra Heavy Duty, MPP type capable of mounting both in horizontal as well as vertical position. The capacitor unit shall have over pressure dis-connector protection & Discharge resistance shall reduce the residual voltage to less than 50 volts within one minute. The reactors & Capacitors are to be controlled in 8 Steps as below complete with banking arrangement, interconnections with suitable size of copper conductor PVC insulated PVC sheathed unarmoured cable, discharge resistance etc. as required.( Set of 15KVAr 7% Reactor + 10KVAr Capacitor is to be connected directly for Transformer compensation under no load condition (Bypassing APFC relay). Necessary provision may be incorporated for automatic switching OFF of fixed capacitors at the time of EB supply failure. )<br>f) Auto manual selector switch with facility for manual control of capacitor bank in the event automatic operation not functioning.<br>g) Exhaust Fan (with thermostat) for cooling of panel<br>h) CT of desired ratio to be fixed in main incomer of LT panel with armoured 2.5 Sq,mm copper conductor control cable from LT panel to capacitor panel.<br>Accepted Make of materials : APFC relay - Beluk/ Schneider/ Siemens<br>Power Capacitors - Shreem / Schneider <br>Digital Meters, PF meter etc - Schneider / Siemens / L&T<br>