Kerala Tourism Development Corporation Limited Tender

Wall Mounted Shelf - 2 Tier of size 1500x300x600mm :<br>18G Ss Shelves With 3 Side Up-Beeded & Front Down Beeded, 2Nos. SS Brackets Of Size 290*150mm With 2Nos. 10 mm Dia Holes In Each Bracket

Work Table With Sink, Bottom Shelf And Rear Splash of size 900x600x(850+150)mm<br>SS 304 16G Sunk In Top Front & Both Sides Turned Up 25mm @45 Deg, returned 25 mm flat, 50mm Down and in 12 Mm. Left Side 6 Mm Projected Out And 10 mm Down Connected To Dish Washer. Rear Side Raised Splash Of 150 mm High,Top Welded To 32x32x3 Mm Thick SS. Angle Framework. 1No. SS 304 16G Sink of size 450x450x300 Mm Deep, Fitted With 1-1/2" Bsp Waste Coupling Inteigral With Top. One Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Type Channel Of Size 20x100x20mm. SS 304 16G 40x40 Mm Four Nos Of Sq. Tubular Legs With Adj. Bullet Feet. Legs Shall Be Welded At Top To The S.S. Angle Framework And Shall Be Positioned From The Table Ends.

Work Table With Sink, Bottom Shelf And Rear Splash of size 1000x600x(850+150)mm<br>SS 304 16G Sunk In Top Front & Both Sides Turned Up 25mm @45 Deg, returned 25 mm flat, 50mm Down and in 12 Mm. Left Side 6 Mm Projected Out And 10 mm Down Connected To Dish Washer. Rear Side Raised Splash Of 150 mm High,Top Welded To 32x32x3 Mm Thick SS. Angle Framework. 1No. SS 304 16G Sink of size 450x450x300 Mm Deep, Fitted With 1-1/2" Bsp Waste Coupling Inteigral With Top. One Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Type Channel Of Size 20x100x20mm. SS 304 16G 40x40 Mm Four Nos Of Sq. Tubular Legs With Adj. Bullet Feet. Legs Shall Be Welded At Top To The S.S. Angle Framework And Shall Be Positioned From The Table Ends.

Wall Mounted Shelf - 2 Tier of size 1000x300x600mm :<br>2Nos 18G Ss Shelves With 3 Side Up-Beeded & Front Down Beeded, 2Nos. SS Brackets Of Size 290*150mm With 2Nos. 10 mm Dia Holes In Each Bracket

Spreader Table With Two Under Shelves & Rear Splash of size 500x700x(850+150)mm:<br>16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm. 4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet.

Two Burner Chinese Cooking Range With Bottom Shelf And Splash, Water Faucet of size 1300x700x(850+400)mm:<br>16G SS 40mm Sunken top Down Beeded On 3 Sides with 32x32x3Mm Thk. boxed SS Angle Frame under support. 16G SS Spalsh of 400mm high from work top. Rear top to be recessed to form a drain channel terminating in a drain outlet of 38 mm slopping towards the drain. 1No. swinging water faucet on top of the chinese wok. 1No. T-50 high pressure burner & 1No. Model-4 Burner. 1No Heavy duty 425mm Dia cast iron vessel rest suitable for Chinese wok with sufficient air vents. 1No 350*350 mm Wide Cast-Iron Vessel Rest. 20G SS On Both Sides And Rear With Airvents & front 18G SS with control knobs. 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25mm under support. 4No’S 40x40 mm16G SS Pipe Legs With Adj. Nylon Bullet Feet

3 Burner Cooking Range With 1 Under Shelf & Rear Splash of size 1650x700x(850+150)mm :<br>SS 304 16G Top Front & Both Side Turned Down 50 mm And In 12 mm. Rear Side Raised Splash Of 150 mm High, & 32x32x3 mm SS Angular Framework Fully Welded. 3 Nos. 350x350 mm, Heavy Duty Cast Iron Removable Vessel Rest. 2 Nos G10 Burners & 1No Model-4 Burner(Canteen Burner) With Pilot & Control. Swg 20 (304) SS Spillage Tray With SS Strip Handle.1 U/S Full Width Non-Rattling Type SS. 304 18G With All Sides Turned Down 40 mm And In 12 mm And Shall Be Reinforced On The Underside With 25x100x25 mm SS 304 16G Inverted Hat Type Channels. Corners Of Shelves Shall Be Cutout And Shall Be Fully Welded To The Centerline Of Legs. All Ends Shall Be Closed, Welded, Ground And Polished Smooth. Legs Four Nos SS 304 16G 40x40 mm Tubular Legs With Adjustable. Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS.Framework And Shall Be Positioned From The Burner Ends.

Tandoor On Wheels - Charcoal of size 900x900x(850+150)mm :<br>SS 304 16G Top All Sides turned down 50 mm and in 12 mm welded to 32x32x3 mm thick SS Angle Frame Work,20G SS Outer Body All Sides,front Ø25 mm 16G SS pipe Handle ,Mud pot in GI Drum, Filled with clay Mixture & insulated with glass wool layer. Front SS Door for charcoal removal door opening, 4 Nos. SS 304 16 G 40 Sq. mm tubular legs Fitted on Ø100 ms Caster Wheels All Swivel With 2 Nos. break Wheels, with long handle lid.

Spreader Table With Two Under Shelves & Rear Splash of size 750x700x(850+150)mm:<br>16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm. 4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet.

Grill Plate With Half Grooved, Bottom Shelf And Rear Splash of size 600x700x(850+150)mm<br>16 SWG SS top with 150 mm high raised splash on rear, returned 50mm & down. Both sides of top rolled down 50 mm flush with body cladding. Worktop to over hang the base body by 50mm from front and 75mm at rear. SWG 20G (304) SS on all sides with air vents on both sides. 40x40 SQ PIPE & 25x25x3 MM SS Angle boxed frame under support. Cooking top of 20 mm thick polished MS plate with 250mm Grooving with 75 mm raised rear and side edges with grease collecting trough in front and grease collecting drawer. 2Nos. of V-600 burners (40,000 btu/hr) with One number Pilot Burner. 16 SWG , 40x40mm SS Square pipe legs with adjustable SS bullet.

Hot Plate With Bottom Shelf And Rear Splash of size 1200x700x(850+150)mm:<br>16 SWG SS top with 150 mm high raised splash on rear, returned 50mm & down. Both sides of top rolled down 50 mm flush with body cladding. Worktop to over hang the base body by 50mm from front and 75mm at rear. SWG 20G (304) SS on all sides with air vents on both sides. 40x40 SQ PIPE & 25x25x3 MM SS Angle boxed frame under support. Cooking top of 20 mm thick polished MS plate with 75 mm raised rear and side edges with grease collecting trough in front and grease collecting drawer. 3 Nos. of V-600 burners (40,000 btu/hr) with One number Pilot Burner. 16 SWG , 40x40mm SS Square pipe legs with adjustable SS bullet.

Spreader Table With Two Under Shelves & Rear Splash of size 450x700x(850+150)mm:<br>16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm. 4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet.

Work Table With Two Under Shelves & Rear Splash of size 1200x600x(850+150)mm:<br>16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm. 4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet.

od149608/2023_2024 : Wall Mounted Shelf - 2 Tier of size 1200x300x600 mm:<br>2Nos 18G Ss Shelves With 3 Side Up-Beeded & Front Down Beeded, 2Nos. SS Brackets Of Size 290*150mm With 2Nos. 10 mm Dia Holes In Each Bracket

od149609/2023_2024 : Work Table With Sink, Bottom Shelf And Rear Splash of size 1200x600x(850+150)mm<br>SS 304 16G Sunk In Top Front & Both Sides Turned Up 25mm @45 Deg, returned 25 mm flat, 50mm Down and in 12 Mm. Left Side 6 Mm Projected Out And 10 mm Down Connected To Dish Washer. Rear Side Raised Splash Of 150 mm High,Top Welded To 32x32x3 Mm Thick SS. Angle Framework. 1No. SS 304 16G Sink of size 450x450x300 Mm Deep, Fitted With 1-1/2" Bsp Waste Coupling Inteigral With Top. One Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Type Channel Of Size 20x100x20mm. SS 304 16G 40x40 Mm Four Nos Of Sq. Tubular Legs With Adj. Bullet Feet. Legs Shall Be Welded At Top To The S.S. Angle Framework And Shall Be Positioned From The Table Ends.

Pickup Counter With Three Side Covering, 2 Under Shelves, 2 Ohs With Rr Heater & Tray Slider of size 1800x(626+300)x(850+450+300)mm :<br>16G SS 304 Work Top Double Beeded On 3 Sides 32x32x3 mm Thick SS Angle Frame under supoort, 2 Nos 18G SS Undershelf Down Beeded On All Sides with 18G SS Channel Of Size 25x150x25 mm under support. 2Nos. 20G SS 2 Over Head Shelves 12” Wide With SS 304 16G Inverted Hat Type Channels, Mounted On Top By Means Of 25Mm Dia Verticals Pipe Will Be Provided & 4Nos. 40 Sq. mm 16G SS Pipe Legs With Adj. SS Bullet feet. Upper Shelf Fitted With IR Lamp Heaters - 2 Nos

OverHead Shelf - 2 Tier of size 1350x300x600mm :<br>2Nos. 18G SS Overhead shelf mounted on 25mm dia ss tuular section. Shelves with all sidedo down Beeded.

od149613/2023_2024 : Dish Landing Table With Chute, Glass Rack Bottom Cross Supports & Rear Splash of size 1700x700x(850+150) :<br>Sunkun Top Made Of 16G SS.Sheet. The Top Will Be Mounted On 32x32x3Mm Thick SS.Angle Frame & Ø 175 Mm Chute Smoothly Welded On Top, Vertical Legs Of Ss 304 16G 40x40 mm Four Nos Of Tubular Legs With Adjustable Nylon Bullet Feet.SS 304 . 25x25 mm Tubular Cross Bracing Welded To Legs At Rear And Both Side & Front Open. Legs Shall Be Welded At Top To The SS. Angle Framework And Shall Be Positioned From The Table Ends.

Loading Table With 2 Sink Unit, Bottom Cross Supports And Rear Splash of size 1700x750x(850+150)mm :<br>SS 304 16G Sunk In Top Front & Right Side Turned Up 75 Mm Returned 50 mm And In 12 Mm. Left Side 6 Mm Projected Out And 10 mm Down Connected To Dish Washer. Rear Side Raised Splash Of 150 Mm High,Top Welded To 32x32x3 Mm Thick SS. Angle Framework 1No. Of Ss 304 16G - 2 Sink 450x450x300 Mm Deep, Fitted With 1-1/2" Bsp Waste Coupling Inteigral With Top. Center Line Of Sink Waste Shall Be Properly Positioned From Edge Of Table. SS 304 16G 40x40 Mm Four Nos Of Sq. Tubular Legs With Adj. Bullet Feet. Legs Shall Be Welded At Top To The S.S. Angle Framework And Shall Be Positioned From The Table Ends. SS 304. 25x25 Mm Tubular Cross Bracing Welded To Legs At Rear And Both Side & Front Open.

Unloading Table With Bottom Cross Supports And Rear Splash of size 1200x650x(850+150)mm :<br>SS 304 16 G sunk in TOP front & Right side turned Up 75 mm returned 50 mm turned down 50 mm and in 12 mm. Rightt side 6 mm projected out and 10 mm down connected to Dish washer. Rear side raised splash of 150 mm high,Top welded to 32x32x3 mm thick S.S. angle framework shall be sound-deadened. SS 304 16 G 40x40 mm Four nos of tubular legs with adj. Nylon bullet feet. Legs shall be welded at top to the S.S. angle framework and shall be positioned from the table ends. SS 304 . 25x25 mm tubular cross bracing welded to legs at rear and both side & front open.

Dish Storage Rack-4 Tier of size 1200x450x1500mm:<br>4 Nos 18G SS Shelves with rear & sides up-beeded & front down Beeded. Each shelf is supported with 20x100x20mm 16G SS Channel Under Support. Uprights are made of 16G SS 38mm round tube section with Adjutable Nylon Bullet Feets.. Top Side Of The Legs Should Be Closed With Nylon End Cap .

Pot Rack - 3 Tier of size 1800x600x1500mm :<br>38Mm Dia*16G Ss Pipe Uprights With Adj. Ss Bullet Feets With Ss Bush Nylon End Closer. 3 Nos Shelves with 32Mm Dia*16G Ss Pipe Cross Supports 18 Mm Dia*16G Ss Pipe Cross Supports At 100Mm C.T.C. Apx.

Pot Wash Grill of size 1350x600x600mm<br>38Mm Dia*16G Ss Pipe Uprights With Adj. Ss Bullet Feets With SS Bush Nylon End Closer 32Mm Dia*16G Ss Pipe Cross Supports 18 Mm Dia*16G Ss Pipe Cross Supports At 100Mm C.T.C. Apx.

Spreader Table With Two Under Shelves & Rear Splash of size 300x600x(850+150)mm:<br>16G SS Work Top Double Beeded On 3 Sides reinforced with 32x32x3mm Thick Angle Frame. 16G SS Splash on rear . 2 Nos 18G SS Undershelves Down Beeded On All Sides supported with 18G SS Hat Channel Of Size 20x100x20mm. 4Nos 16G SS 40x40mm 16G SS Square Pipe Legs With Adj. SS bullet feet.

Hot Plate With Bottom Shelf And Rear Splash of size 900x600x(850+150)mm:<br>16 SWG SS top with 150 mm high raised splash on rear, returned 50mm & down. Both sides of top rolled down 50 mm flush with body cladding. Worktop to over hang the base body by 50mm from front and 75mm at rear. SWG 20G (304) SS on all sides with air vents on both sides. 40x40 SQ PIPE & 25x25x3 MM SS Angle boxed frame under support. Cooking top of 20 mm thick polished MS plate with 75 mm raised rear and side edges with grease collecting trough in front and grease collecting drawer. 2Nos. of V-600 burners (40,000 btu/hr) with One number Pilot Burner. 16 SWG , 40x40mm SS Square pipe legs with adjustable SS bullet.

Two Burner Cooking Range With Bottom Shelf And Rear Splash of size 1100x600x(850+150)mm<br>SS 304 16G Top Front & Both Side Turned Down 50 mm And In 12 mm. Rear Side Raised Splash Of 150 mm High, & 32x32x3 mm SS Angular Framework Fully Welded. 2 Nos. 350x350 mm, Heavy Duty Cast Iron Removable Vessel Rest. 1 No G10 Burners & 1No Model-4 Burner(Canteen Burner) With Pilot & Control. Swg 20 (304) SS Spillage Tray With SS Strip Handle.1 U/S Full Width Non-Rattling Type SS. 304 18G With All Sides Turned Down 40 mm And In 12 mm And Shall Be Reinforced On The Underside With 25x100x25 mm SS 304 16G Inverted Hat Type Channels. Corners Of Shelves Shall Be Cutout And Shall Be Fully Welded To The Centerline Of Legs. All Ends Shall Be Closed, Welded, Ground And Polished Smooth. Legs Four Nos SS 304 16G 40x40 mm Tubular Legs With Adjustable. Nylon Bullet Feet. Legs Shall Be Welded At Top To The SS.Framework And Shall Be Positioned From The Burner Ends.

Storage Rack-5 Tier of size 1200x450x1800mm<br>5 Nos 18G SS Shelves with rear & sides up-beeded & front down Beeded. Each shelf is supported with 20x100x20mm 16G SS Channel Under Support. Uprights are made of 16G SS 38mm round tube section with Adjutable Nylon Bullet Feets.. Top Side Of The Legs Should Be Closed With Nylon End Cap .

Supply, Testing and commissioning of Tilting Wet Grinder with following specificationbrCapacity-15 LitrebrSS 304 16 Swg SS Drum Revolving Drum, Grinding Stone, Frame All SS brMotor: Crompton/Abb Ele: 1.0 Hp/3Ph/50 Hz.

Supply Testing and commissioning of Tilting Wet Grinder with following specificationbrCapacity- 10 LitrebrSS 304 16 Swg SS Drum Revolving Drum, Grinding Stone, Frame All SS brMotor: Crompton/Abb Ele: 0.5 Hp/3Ph/50Hz

Supply, Testing and commissioning of Water Cooler with following specificationbrCapacity- 40 LtrbrFaster cooling, Eco-friendly, In situ power-saving PUF insulationbrSturdy compressor and trouble-free operation, Silent operationbrStainless Steel body, Stainless Steel tank, Easy controlsbrSpeedy drainage, Storage capacities: 40 Lbr

Supply, Testing and Commissioning of 3 Door U/C Salad Counter with following specificationbrGross Volume: 417 Liters, Net Weight: 118 kgbrInternal dims (mm): 1270 (W) x 590 (D) x534(H)brTemperature Range: -2°C to 8°CbrShelf: 6 nos. of shelvesbrRefrigerant: R134a / 160 gramsbrPower Supply: 230V AC / 50Hz/Single

Supply, Testing and Commissioning of Bain Marie with following specificationbr Food Pick Up Counter With One Under Shelf, Two Overhead Shelves, Three Sides Covering And ( 1No. 1/1 X 150 & 4Nos. 1/2 X 150Mm Deep Gn Pans With Lids) Tray Slider :brEntire equipment including under frame shall be made of SS 304. The tank of the Bain Marie shall be provided with an on‐line connection with a ball valve and a drain valve. Water sensor to be provided in the unit for preventing the heating element getting damaged due to no water. Unit shall have 2nos. of 3kw water immersion heaters with rotary On‐OFF switch, indicating lamps and imported thermostat. It shall be provided with 2 meter supply cord with industrial top. 2Nos. 18G SS Overhead shelf mounted on 25mm dia ss tubular section.

Supply, Testing and commissioning of Chest Freezer with following specifications brTop Open (Single Door)brInternal dimension (mm): 430(W ) x 465 (D) x 515 (H)brGross Volume: 103 Liters, Net volume: 96 LitersbrProduct Freezing temperature: -17°C to -22°CbrNo. of Basket: 1 No.brInsulation: 80mm Polyurethane

Supply, Testing and commissioning of 2 Door Work Top Under Counter Refrigerator With Back Splash with following specificationsbrGross Volume: 315 LitersbrInternal dims (mm): 1132(W) x 480 (D) x 588 (H)brTemperature Range: -2°C to 12°CbrShelf: 4 nos. of shelvesbrRefrigerant: R134a /260 gramsbrPower Supply: 230V AC / 50HzbrHeat Rejection: 0.56 kWbrCompressor Capacity (Watt): 366WbrTemperature control: Electronic

Supply and providing Sandwich Griller (Single) with Heating coil, On-Off switch, Thermostat, Indicator Lamps etc. The griller shall have a capacity of 4 slices and shall operate on 240 V Single Phase AC Supply

Supply and installation of reputed make automatic hood type dish washing machine having wash, rinse and dryer complete in all respects. brThe requirements of the machine should be nearer to the following:brDimension: 600mm X 600 mm X 1380 mm (maximum)brWash Capacity:30 racks/hr minimumbr (1500 to 1800 saucers or br 1400 to 1600 rice bowls or br 1800 to 2000 glass/hr) Power Supply: 3 phase,400V,50Hz AC

Supply of 20Kg/day or nearest higher capacity Ice cube machine working on 230V single phase 50 Hz AC supply and having a storage capacity of minimum 4kg and of stainless steel body and having longer life operation of good quality and reputed make

Supply, Testing and commissioning of good quality and reputed make Mixer/Juicer.

Supply and providing Glue based Insect-O-Cutor with necessary components like insect attracting tube light having minimum 9000 hours life and working on 240V, 50 Hz AC supply including all wall/ceiling mounting accessories etc. complete