Kerala State Palmyrah Products Development And Workers Welfare Corporation Limited Tender

5.1.2 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - all work up to plinth level 1:1:5:3 )1cement 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size.

6.3.1 Brick work with common burnt clay machine moulded perforated bricks of class designation 12.5 conforming to IS:2222 in superstructure above plinth level up to floor five level in cement mortar 1:6 (1 cement : 6 coarse sand): with F.P.S. (non modular ) bricks

5.3 reinforced cement concrete work in beans, suspended floors, roofs, having slop up to 15 degree landings, balconies, shelves, chchaijjas lindels, bands, plain window sills, staircase and spiral stair case up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with :15:3 (1 cement:1.5 coarse sand (zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.2 centering and shuttering including strutting, etc. and removal of form for :walls (any thickness) including attached pilasters, butteresses plinth and string coarses etc.

5.9.3 centering and shuttering including strutting, etc. and removal of form for : suspended floors, roofs, landings, balconies and access platform

5.22.5 steel reinforcement for R.C.C work including straitening, cutting, bending, placing in position and binding all complete up to plinth level hard drawn steel wire fabric

4.1.8 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

13.1.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

13.9.1 cement plaset 1:3 ( 1 cement : 3 coarse sand) finished with a floatting coat of neat cement. 12mm cement plaster

13.16.1 6 mm cement plaster of mix : 1: 3 (1 cement: 3 fine sand)

13.43.1 applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: water thinnable cement primer

50.9.1.1 proving wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast luggs or dash fastner shall be paid for seperately), using good quality Anjili wood or jack wood.

9.48.1 providing and fixing M.S . Grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to steel windows by welding

10.30.1 providing and fixing glass panes with putty and glazzing clips in steel doors, windows, clerestory windows all complete with : 4.0 mm thick glass panes

50.9.2.1 providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm thick shutters including ISI marked M.S. pressed butt hinges bright finished of required size with necessary scews, excluding pannelling which will be paid for seperately, all complete as per direction of engineer -in - charge -. using anjili or jack wood.

50.9.4.1 providing and fixing paneling or paneling and glazing in paneled or paneled and glazed shutters for doors, windows and clerestory windows (area of opening for panel insert excluding portion inside grooves or rebates to be measured) paneling or paneled or paneled and glazed shutters 25 mm to 40 mm thick using good quality anjili or jack wood

13.60.1 wall painting with acrylic emulsion paint of approved brand and manufature to give an even shade: two or more coats on new work

13.61.1 painting with synthetic enamel paint of approved brand and manufacture to give an even shade : two or more coates on new one

14.29 providing and fixing MS round or square bars with MS flats at required spacing in wooden frames of windows and clerestory windows

11.37 providing and laying ceramic glazed floors tiles of size 300 X 300 mm (thickness to be specified by the manufacturer), of first quality confirmingti IS :15622, of approved make, in colors such as white ivory gray fume red brown, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), including pointing the joints with white cement and matching pigment etc, complete

11.38 providing and laying ceramic glazed floor tiles of size 300 X 300 mm (thickness to be specified by the manufacturer), of first quality confirming to IS : 15622, of approved make, in all colours, shades, except white, ivory,gray, fume red brown, laid on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand) including pointing the joints with white cement and matching pigment etc, complete

11.41.1 providing and laying vertified floor tiles in different size (thickness to be specified by the manufacturer) with water absorption less than .08% and confirming to IS:156222, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) including grouting the joints with white cement and matching pigments etc complete point size of tile 500 X 500 mm

17.7.1 providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of stadard pattern including painting of fittings and brackets, cutting and making good the walls where ever required: white vitreous china wash basin size 630 X 450 mm with a pair of 15 mm C.P. brass pillar taps

17.7.9 providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of stadard pattern including painting of fittings and brackets, cutting and making good the walls where ever required: white vitreous china surgeon type wash basin of size 660 X 460 mm with single 15 mm C.P. brass pillar taps with elbow operator levers ISI Marked

18.48 providing and placing on terrace (at all floors levels) polyethylene water storage tank : ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank 1000 litre

50.18.7.3.2 providing and fixing P V C pipes, fittings including fixing the pipe with clamps at 1 m spacing. This includes jointing of pipes and fittings with one step P V C solvent cement and testingof joints complete as per direction of engineer - in- charge 25 mm dia 10 kg f bar cm 2 - internal work - exposed on wall

50.18.8.9.2 providing and fixing P V C pipes, fittings including fixing the pipe with clamps at 1 m spacing. This includes jointing of pipes and fittings with one step P V C solvent cement and testing of joints complete as per direction of engineer - in- charge. concealed work, including cutting chases and making good the wall etc. 110 mm pipe 4 kgf per cm 2.

50.18.9.4.2 providing and fixing PVC pipes including joints of pipes with one step PVC solvent cement trenching, refilling and testing of joints complete as per direction of engineer in charge. 32 mm dia 6 kgf / cm 2

10.16.2 steel work in built up tubular (round, square or rectangular hollow tubes etc) trusses etc including cutting hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc complete. hot finished seamless type tubes

17.3.1 providing and fixing white virtious china pedastal type water closet (European type) with seat and lid, 10 ltr low level whitw virtious china flushing cistern and C.P. flush bend with fittings and C.I brackets, 40 mm flush bend, overflow arrangement with special of standard make and mosquito proof cupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors where ever required : W. C. pan with ISI marked while solid plastic seat and lid

9.142.1 35 mm thick factory made solid panel PVC door shutter, made out of single piece extruded solid PVC (+/- .2mm) thick, having styles and railes (except lock rail)of size 95 mm X 35 mm X 5 mm, out of which 75 mm shall be flat and 20 mm shall be tapered ( on both side) , having one side thickness of 15 mm integrally extruded on the hinges side of the profile for better screw holding power, including reinforcing with MS tube of size 40 mm X 20mmX 1mm, joints of styles and rails to be mitered cut and joint with the help of PVC solvent cement, self driven, self taping screw and M.S. rectangular pipies bracket of size 190 mm X 100 mm of cross section size 35mm X 17 mm s 1 mm at each corner. single piece extruder 5 mm thick solid pvc lock rail of size 115 mm X35 mmX35mm, out of which 95 mm to be flat and 20 mm to be tapered at both ends, having 15 mm solid core in middle of rail section integrally extruded, fixing the styles and rails with the help of solvent and self driven and self tapping screws of 125 mmX11mm, including providing 5mm single piece solid pvc extruded sheet inserted in the door as panel, all complete as per manufactures specification and direction of engineer in charge. non decorative finish (matt finish)

Electrification work

centage charges