Kerala State Nirmithi Kendra Tender

12.45.4 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60.

13.88 : Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

11.37 : Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

8.31 : Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

22.5 : Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg /sqm mixed with water proofing cement compound @ 0.126 kg/ sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

od76310/2023_2024 : Supplying and fixing full height wooden Paneling a combination of 16mm and 9 mm BWR/BWP plywood and all exposed portions of the plywood shall be finished with 1mm thick Laminate of approved make and shade. Including all materials and labour charges etc.

od76319/2023_2024 : Supplying and fixing full height wooden partition by covering with 8mm BWR plywood on either side of 16mm BWR Plywood frame work and all exposed portions of the plywood shall be finished with 1mm thick Laminate of approved make and shade. Including all materials and labour charges etc.

od76321/2023_2024 : Supplying and fixing Glass partition with 6mm plain glass by covering with 9mm BWR/BWP plywood on either side of 16mm Plywood frame work and all exposed portions of the plywood shall be finished with 1mm thick Laminate of approved make and shade.Rate including all materials and labour charges etc.

od76331/2023_2024 : Providing and fixing Flush Door frame using a combination of 6 mm, 9 mm, 12 mm and 18 mm BWR Grade Plywood overlaid with 1mm laminate Rate quoted shall include all material, labour charges, cost of conveyance,etc

od76333/2023_2024 : Providing and fixing Flush Door in position overlaid with 1mm laminate including vision panel,Tower bolt hinges etc Rate shall include all material, labour charges etc

od76335/2023_2024 : Supplying and fixing Door closer including all materials and labour charges etc

od76336/2023_2024 : Supplying and fixing Door Handle with lock including all materials and labour charges etc

od76337/2023_2024 : Providing and fixing all window in position Roller Blinds, including all standard fitments and fabric. Rate quoted shall include all material, labour charges, cost of conveyance etc.

od76338/2023_2024 : Supplying and fixing Conference table of size 8600mm (l) x 600 mm (w) x 750 mm (h) to be formed out of 18 mm thick scratch resistant and deflection resistant Pre-laminated particle board. All exposed edges lipped with PVC edge banding with provision for wire manager.The rates including all materials and labour charges etc

od76339/2023_2024 : Providing and fixing in place Centre Table of size 900 mm x 450 mm x 450 mm The rate will include all other necessary hardware,materials and labour charges etc

od76340/2023_2024 : Supplying and providing rectangular workstation of size 1200 mm (l) x 600 mm (w) x 750 mm (h) with vertical Coloured glass member going up to 300 mm in height and table top to be formed out of 18 mm thick Pre-laminated particle board, laminate used for table top shall be scratch resistant & deflection resistant with all exposed edges lipped with PVC edge banding. Table top shall be supported on MS powder coated RAS legs or prelam gable ends including all materials and labour charges etc

od76341/2023_2024 : Providing and fixing Mobile Pedestal of size 400 mm (l) x 400 mm (w) x600 mm (h). shall be formed out of 18 mm thick Pre Laminated Board and all exposed edges lipped with PVC edge banding. Including all materials and labour charges etc

od76342/2023_2024 : Supplying Executive High Back net chair with hydraulic lifting mechanism and tilt lock, shodded on metal star legs with castors

od76343/2023_2024 : Engaging Labour for dismantling the existing partition, paneling,Texture Paint and door etc

9.105.2 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.75 mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum board conforming to IS : 2095 : part I

od76355/2023_2024 : Providing and fixing Skirting ( height 10cm ) for Gypsum partition using of 9 mm, BWR/BWP Grade Plywood overlaid with 1mm laminate Rate shall include all material, labour charges etc

ELECTRICAL WORKS

1.10.3 : Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C

1.12 : Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.7.1 : Wiring for circuit/ sub main wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

1.28.2 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.3 Module

1.28.5 : Supplying and fixing following Modular base & cover plate on existing modular metal boxes etc. as required.8 Module

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

2.5.3 : Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)12 way (4 + 36), Double door

2.3.2 : Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator8 way, Double door

2.2.13 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required100 Amp, 30 KA 4 Pole

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

2.15.2 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

od76324/2023_2024 : Supply and fixing Led 18w 250mmx 250mm Panel Light including all materials and labour charges etc

od76326/2023_2024 : Supply and fixing Led Strip Light including all materials and labour charges etc

od76328/2023_2024 : Supply and fixing Punch lamp including all materials and labour charges etc

od76329/2023_2024 : Supply and fixing drive including all materials and labour charges etc

od76330/2023_2024 : Supplying and fixing 20mm flexible conduit for wiring including all materials and labour charges etc.

od76332/2023_2024 : Supplying and fixing Wall Fan including all materials and labour charges etc.

od76334/2023_2024 : Supply and fixing Pendent lamp including all materials and labour charges etc

AIR-CONDITIONING WORKS

od76302/2023_2024 : Supplying and fixinng 2 TR 3 Star Split AC with cordless remote Full Copper Model including all installation charges etc

od76306/2023_2024 : Supply and fixing 5 kv stabilizer including all installation charges etc

od76309/2023_2024 : Supply and fixing outdoor stand including all materials and labour charges etc

od76313/2023_2024 : Supply and fixing copper Pipe installation for split A/c including all materials and labour charges etc complete

NETWORKING WORKS

od76300/2023_2024 : Supplying and fixing Switch 16 Port Giga Unmanaged including all materials and labour charges etc.uding all materials and labour charges etc.

od76301/2023_2024 : Supplying and fixing CEILING MOUNT ACCESS POINT WIRELESS N300 2.4ghz including all materials and labour charges etc.

od76303/2023_2024 : Supplying and fixingPatch Panel 24 Port Unloaded including all materials and labour charges etc.

od76304/2023_2024 : Supplying and fixing Keystone Rj45 Cat6 including all materials and labour charges etc.

od76305/2023_2024 : Supplying and fixing Rj45 Connector Cat6 100n Box including all materials and labour charges etc

od76307/2023_2024 : Supplying and fixing Fan Four All Rack Support including all materials and labour charges etc.

od76308/2023_2024 : Supplying and fixing Cantilever Tray

od76312/2023_2024 : Supplying and fixing Cable Manager 1u including all materials and labour charges etc.

od76314/2023_2024 : Supplying and fixing Hw Screw 10nos M6 Cage Nuts including all materials and labour charges etc

od76316/2023_2024 : Supplying and fixing Metal Box 1 Module including all materials and labour charges etc.

od76317/2023_2024 : Supplying and fixing Metal Box 3 Module including all materials and labour charges etc.

od76318/2023_2024 : Supplying and fixing Patch Cord Cat6 1m including all materials and labour charges etc.

od76320/2023_2024 : Supplying and fixing Keystone Rj45 Cat6 including all materials and labour charges etc.

od76322/2023_2024 : Supplying and fixingTrunk Panel 6m including all materials and labour charges etc.

od76323/2023_2024 : Supplying and fixingNetwork Cable Cat6 Finolex + Fitting Materials + Labour Charge including all materials and labour charges etc.

od76325/2023_2024 : Engaging labour for fixing Network Crimping + Rack Dressing + Commissioning including all materials and labour charges etc.

od76327/2023_2024 : Supplying and fixing Wire Tie 100/2nos + Tape 20nos including all materials and labour charges etc.

PLUMBING WORKS

18.53.1 : Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS: 893115 mm nominal bore

17.7.2 : Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap

17.73.2 : Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighting not less than 190 gms

18.15.1 : Providing and fixing brass bib cock of approved quality :15 mm nominal bore

18.16.1 : Providing and fixing brass stop cock of approved quality :15 mm nominal bore

17.32.2 : Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing :Rectangular shape 453x357 mm

18.65 : Providing and fixing PTMT Soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fittings arrangements, weighing not less than 106 gms.

50.18.7.2.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with claps at 1.00 metre spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 20 mm dia 12Kgf/cm2 - Internal work - Exposed on wall

50.18.7.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 10Kgf/cm2- Internal work - Exposed on wall

50.18.7.6.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 10 Kfg/cm - Internal work- Exposed on wall

50.18.8.9.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2

od76311/2023_2024 : Providing and fixing European water closet Ceramic Floor Mounted One Piece 4D Flushing Technology including all materials and labour charges etc.

50.17.1.5 : Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

od76315/2023_2024 : Providing 6" silt with CP gratings including all materials and labourcharges etc.