Kerala State Housing Board Tender

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

50.6.2.1 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.2.2 : Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

od9517/2017_2018 : Providing & fixing G I sliding gate 210 cm height from ground, using G I tubular 100x40x2 mm for outer frame, 70x40x2 mm intermediate vertical and horizontal. The space between is provided with 25 mm dia SS hollow pipes to be welded @ 10cm c/c or nearest in both directions as per approved drawing on outer frames with 25 mmx 2mm sq.SS tubes, including providing MS locking arrangements, cutting to size and shapes where ever required, welding, applying priming coat etc. complete as per the direction of site engineers.<br>

od9357/2017_2018 : Providing & fixing G I openable gate 210 cm height from ground, using G I tubular 100x40x2 mm for outer frame, 70x40x2 mm intermediate vertical and horizontal. The space between is provided with 25 mm dia SS hollow pipes to be welded @ 10cm c/c or nearest in both directions as per approved drawing on outer frames with 25 mm x 2mm sq.SS tubes, including providing MS locking arrangements,cutting to size and shapes where ever required, welding, applying priming coat etc. complete as per the direction of site engineers.<br><br>

od10518/2017_2018 : Providing & fixing G I grill 160 cm length and 55 cm height, using G I tubular 70x30x2 mm for outer frame, 25x25x2 mm for anchoring into the masonry or RCC. The space between is provided with 25 mm diax 2mm SS hollow tubes to be welded @ 10cm c/c or nearest in both directions as per approved drawing on outer frames with 25 mmx 2mm sq.SS tubes, including cutting to size and shapes where ever required, welding, applying priming coat etc. complete as per the direction of site engineers.<br>

od10097/2017_2018 : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture etc complete for gate and horizontal bars.<br>

od10098/2017_2018 : Painting exterior walls with superior quality anti fungal exterior emulsion paint ASIAN PAINTS APEX or equivalent, 2 coats, over one coat cement primer including cost & conveyance of all materials to site, all labour charges including hire & labour charges for scaffolding etc; complete for all floors<br>

9.76 : Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

App-B: Truss work

15.58 : Demolishing R.C.C. work by mechanical means and stockpiling at designated locations and disposal of dismantled materials up to a lead of 1 kilometre, stacking serviceable and unserviceable material separately including cutting reinforcement bars.

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.6 : Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

od10618/2017_2018 : Supplying and fixing 100 mm G.I Pipe (114.3 mm OD x 3.05 mm wall thickness (11 gauge) 'having a weight of 8.52kg/m or nearest available size including applying priming coat etc.complete<br>

od10619/2017_2018 : Supplying and fixing 150x150x6mm or nearest available size M.S Plate (male) for anchoring in to cement concrete, welded with holding down M S bolts at top and M S Tor steel for a length of 45 cm at bottom etc.complete<br>

od10620/2017_2018 : Supplying and fixing 150x150x6mm or nearest available size M.S Plate (female) for bolting with M S Plate already fixed in the concrete, after wlded with GI pipes at top etc.complete<br>

od10621/2017_2018 : Supplying and fixing 150x150x6mm or nearest available size M.S Plate for placing the wall plates, at top of GI pipes including welding etc. complete<br>

od10622/2017_2018 : Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., using 76x38x3mm(4.90kg/m) nearest available size rectangular box sections including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.<br>

od10710/2017_2018 : Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., using 25x25x2.0mm (1.475kg/m) or nearest available size rectangular box sections including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.<br>

od10623/2017_2018 : "Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15- 18 microns using self drilling/ self tapping screws complete : <br>Ridges plain (500 - 600mm)"<br>

od10624/2017_2018 : "Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required."<br>

od10625/2017_2018 : Supplying and providing 160 mm PVC split pipe for rain water gutter with necessary clamp etc.<br>

od10626/2017_2018 : Providing 110mm PVC down water pipe[6Kgf/cm2] for draining rainwater by jointing with solvent cement fixing to wall with iron clamping and screws to T.W plug embedded in cement morter etc. complete.<br>(Ref. 50.18.9.9.1)

od10097/2017_2018 : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture etc complete for gate and horizontal bars.<br>

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

50.2.26.1 : Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

od10707/2017_2018 : "Plastering with Cement mortar 1:4, 12 mm thick one coat for inside and out side walls of all floors, etc. including cost and conveyance of all materials and labour,floated hard and trowelled smooth,watering,curing etc. complete. <br>from 10m to 13m ht from the ground level"<br>

od10098/2017_2018 : Painting exterior walls with superior quality anti fungal exterior emulsion paint ASIAN PAINTS APEX or equivalent, 2 coats, over one coat cement primer including cost & conveyance of all materials to site, all labour charges including hire & labour charges for scaffolding etc; complete for all floors<br>

od10708/2017_2018 : Providing and laying factory made pre cast tiles (Eurocone or equivalent) 22 mm thick (medium colour) or nearest available size for flooring at parking area of inside portion of building in ground floorlaid in floors, and landings, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including cleaning etc.complete, on 20 mm thick bed of cement mortar 1:4 (1 cement:4 coarse sand) : & direction of Engineer -in-Charge<br>

16.91.2 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

25.7 : Designing, fabricating, testing, installing and fixing in position Curtain Wall withAluminium Composite Panel Cladding, with open grooves for linear as well ascurvilinear portions of the building , for all heights and all levels etc. including:a) Structural analysis & design and preparation of shop drawings for pressureequalisation or rain screen principle as required, proper drainage of water to makeit watertight including checking of all the structural and functional design.b) Providing, fabricating and supplying and fixing panels of aluminium compositepanel cladding in pan shape in metalic colour of approved shades made out of4mm thick aluminium composite panel material consisting of 3mm thick FR grademineral core sandwiched between two Alumini um sheets (each0.5mm thick). Thealuminium composite panel cladding sheet shall be coil coated, with Kynar500based PVDF / Lumiflon based fluoropolymer resin coating of approved colourand shade on face # 1 and polymer (Service) coating on face # 2 as specified usingstainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backerrods etc.c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanisedwith serrations and serrated washers to arrest the wind load movement, fasteners,SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators toprevent bi-metallic contacts all complete required to perform as per specificationand drawing The item includes cost of all material & labour component, the cost ofall mock ups at site, cost of all samples of the individual components for testing inan approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wallwith aluminium composite panel cladding till the handing over of the building foroccupation. Base frame work for ACP cladding is payable under the relevantaluminium item.s The Contractor shall provide curtain wall with aluminiumcomposite panel cladding, having all the performance characteristics all complete, as per the Architectural drawings, as per item description, as specified, as per theapproved shop drawings and as directed by the Engineer-in-Charge.However, for the purpose of payment, only the actual area on the external face ofthe curtain wall with Aluminum Composite Panel Cladding (including width ofgroove) shall be measured in sqm. up to two decimal places.

od10709/2017_2018 : "Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) to the required shape etc. complete."for grills above CC gutters using 50x10mm SS flats (3.95kg/m) as outer frame and 25x10mm SS flats (1.98kg/m) as intermediate horizontals<br><br>

Appendix C : LAND SCAPING

2.8.1 : Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

50.6.2.1 : Solid block masonry using pre cast solid blocks (Factory made) of size 30x20x15 cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15cm in: CM 1:6 ( 1 cement :6 coarse sand) etc complete

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

5.9.16.1 : Centering and shuttering including strutting, etc. and removal of form for:Edges of slabs and breaks in floors and wallsUnder 20 cm wide

5.2.2 : Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

50.6.2.2 : Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

2.25 : Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

od10098/2017_2018 : Painting exterior walls with superior quality anti fungal exterior emulsion paint ASIAN PAINTS APEX or equivalent, 2 coats, over one coat cement primer including cost & conveyance of all materials to site, all labour charges including hire & labour charges for scaffolding etc; complete for all floors<br>

od10711/2017_2018 : Providing and making turfing with Mexican buffellow grass etc. complete. <br>

od10712/2017_2018 : Providing and fixing cast iron gratings 15 cm height etc. complete. <br>