Kerala State Film Development Corporation Limited Tender
Everything can be found here in your one-stop destination for all types of Kerala tenders online - be it Kerala PWD tenders or an LSGD Kerala tender. Search from across the categories, cities, and authorities while having the option to download tender-related documents. Also, get to know how to register as a bidder and how to bid online for Kerala tenders.
Costs
EMD
₹ 5,00,000Document Cost
Refer DocumentsTender Fee
Refer Documents
Description
Scription for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user this is tender description for unregistered user
Contact
Tender Id
2019_KSFDC_276459_1Bid Award Id
ViewTender No
53/P1/18/KSFDC/Project 1(R)Tender Authority
Kerala State Film Development Corporation Limited ViewPurchaser Address
-Website
http://etenders.kerala.gov.in
GEM & Bid Advisory Services
Get portal registration, tender bidding, product/service listing or vendor/MSME certification services at a nominal cost
Documents
BOQ Items
Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials. All kinds of soil
1469.07
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
5418.7
-
-
Providing and filling with contractor's own approved earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of Engineer-in-charge
11378.47
-
-
Providing, injecting chemical emulsion for Pre-constructional Anti-Termite Treatment along external walls below concrete or masonry apron using chemical emulsion at 2.25 Litre/m including drilling and plugging of holes with chlorophyriphos emulsion concentrate 20% diluting in water to 1% concentration including cost of chemicals, diluting in water to 1% concentration, labour, HOM of equipments complete as per specification
2816.17
-
-
Providing and laying cast in situ cement concrete 1:4:8 including shuttering, form work, dewatering, compacting, curing etc complete - All work up to plinth level (1 Cement: 4 Sand: 8 graded stone aggregate 40mm size)
1734.35
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.- All works upto plinth level
4365.47
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. - All works above plinth level upto floor V level
2954.54
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Foundations, footings, bases of columns, etc. for mass concrete
2193.33
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : walls including attached pilasters, buttersses, plinth and string courses etc
6035.08
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Suspended floors, roofs, landings, balconies and access platforms
10807.85
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers
11996.82
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Columns ( including circular), pillars, piers, abutments, posts and struts
6391.1
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Stairs ( Excluding landings) except spiral staircase
600.64
-
-
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 RM or part thereof (Plan area to be measured). For suspended floors, roofs, landings, beams and balconies
7379.25
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - upto plinth level.
528809
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - above plinth level at all levels
474633
-
-
Providing and filling in position bitumen mix filler of Proportion 80 kg. of hot bitumen, 1 kg. of cement and 0.25 cubic RM of coarse sand for expansion joints.
1.31
-
-
Providing and fixing sheet covering over expansion joints with iron screws as per design. Aluminium fluted strips 3.15 mm thick - 150mm wide
233.3
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in CM 1:6 in basement and superstructure above plinth level up to floor V level in all shapes and sizes including all materials, labour charges, scaffolding, curing complete as per specification
110.4
-
-
Providing and fixing of wall cladding using 20mm thick gangsaw water cut grey granite or any color in CM 1:3 proportion cut to required shape,pattern with paper joints finished with cement mortar using white cement and color pigment to match the color of slab making through jointing with sealant making holes 25mm x 12mm grooves in joints including curing etc
39.12
-
-
Providing and constructing pre cast concrete solid block (Factory made) with compressive strength not less than 35kg/Sq M with cement mortar 1:4 masonry with solid concret blocks of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor three level including cost of materials, labour charges, scaffolding, curing complete as per specification.
1320.66
-
-
Providing and constructing pre cast concrete solid block (Factory made) with compressive strength not less than 35kg/Sq M with cement mortar 1:4 masonry with solid concret blocks of size 40x20x10cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor three level including cost of materials, labour charges, scaffolding, curing complete as per specification.
21.58
-
-
Providing and constructing Laterite masonry with neatly dressed laterite stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor three level including all cost of materials, labour charges, scaffolding, curing etc.
194.35
-
-
Providing wood work in frames of doors, windows, clerestory windows, ventilator and other frames, wrought framed or assembled including making plaster grooves and fixed in position with hold fast lugs or with dash fasteners of required dia & length using good quality Anjili wood /jack wood including all materials, labour, HOM of machineries complete as per specifications and drawings and as directed by the Engineer-in-Charge
2.8
-
-
Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, including all materials, labour, etc complete as per approved drawing & direction of Engineer-in-Charge.
3.6
-
-
Providing and fixing factory made uPVC wooden finish colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDMgasket, wool pile, zinc alloy (white powder coated) handle on one side ofextreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.
284.04
-
-
Providing and fixing ISI marked flush door shutters of 30mm thick conforming to IS : 2202(Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including necessary stainless steel butt hinges with screws and other door fittings like door handle, tower bolt, stopper, aldrop etc of approved make, etc including all materials, accessories, labour as required for satisfactory completion of work as per the drawing and as directed by the Engineer-in-Charge.
117.42
-
-
Providing and fixing of factory made 40mm thick marine ply, Veneer finished flush door shutters of approved make and design, shutters fixed to Dorma BB 4430 or equivalent 100x75x3mm (heavy duty) 3 Nos of ball bearing hinges, class 8, in satin stainless steel finish grade 304 to BS 7352, with necessary SSS screws including any additional lipping/cutting, plaining, etc including all materials, labour as per the drawing and as directed by the Enigneer-in-Charge
235.44
-
-
Providing and fixing 1 mm thick M.S. sheet door with frame and diagonal braces of size 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners with handle, stoppers and locking arrangements etc including applying a priming coat of red lead paint cost of materials, labour, HOM of machinery complete as per specification.
2.52
-
-
Providing and laying 20mm thick flame finished machine cut rough Granite flooring to locations as specified of approved brand, quality, TAN Brown/Jet Black colour having uniform shade, with paper thin joint and to required slope, set on 20mm thick cement mortar 1:4, including fixing of granite with cement paste and pointing the granite joints with approved quality and colour pigmented, cement based joint filler grouts (Fosroc -Nitotile grout or equivalent) to match the shade of granite, etc., The rate shall include for cost of providing and laying patterns, borders, inlays, cost of materials, wastages, labour, tools & plants, loading and unloading charges, transportation , curing, cleaning, all other incidental charges, etc ., complete with all leads and lifts as per specifications and drawings at all levels and as per the instructions of Engineer in Charge.
5607.4
-
-
Providing and fixing I st quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades of any size as approved by Engineer -in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per Sq M, including pointing in white cement mixed with pigment of matching shade complete in all levels and as directed by the Engineer-in-charge
990.32
-
-
Providing and laying vitrified floor tiles 600 x 600mm of approved make, (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ Sq M including grouting the joints with white cement and matching pigments etc., complete in all levels and as directed by the Engineer-in-charge
362.78
-
-
Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of Ist quality conforming to IS : 15622, of approved make, in all colours, shades, laid on 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 Coarse sand), including pointing the joints with white cement and matching pigments etc., complete in all levels and as directed by the Engineer-in-charge
103.64
-
-
Providing and Fixing 15 mm densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone /cosmos /Hexa or equivalent of size 595x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per Sq M including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main 'T' of size 24 x 28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24x28 mm made of 0.33 mm thick (minimum) sheet to be inter locked at middle of the 1200x600 mm panel to from grid of size 600x600 mm, resting on periphery walls/partitions on a Perimeter wall angle pre-coated steel of size (24x24x3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including cutting / making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever require. Main 'T' runners to be suspended from ceiling using G.I sLotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size of 85x30x0.8 mm, spaced at 1200mm centre to centre along main 'T' bottom exposed with 24 mm of all T- sections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by by engineer-in-charge. Note:- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 Sq M. The calcium silicate ceiling tiles shall have NRC. value of 0.50 (Minimum), light reflection 85% non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity 0.043 w/m 0 KC.
362.94
-
-
Providing and laying Pigmented granolithic flooring of 52mm thick (which includes base concrete and top wearing coat 12mm thick in 1:6 (1 cement and 6 parts of 6mm down graded aggregate) in panels not more than 20 Sq M. in plan with cement concrete M20 grade by using coarse graded aggregate of 6 to 20 mm size, laid monolithic with floor concrete and finished smooth with power trowel including preparation of concrete surface and form work. The screed strips shall be fixed on the base concrete with 6 mm thick solid aluminium or other metals strips for effective separation of panels not exceeding 20 Sq M. in plan, unevenness in floor finish shall not exceed +2mm in Cum area, curing, grouting of lugs, etc. The rate shall include cost of materials, labour, tools & plants, loading and unloading, transportation, scaffolding and all other incidental charges etc., with all leads and lifts, complete as per specifications, drawings and as directed by the Engineer-in-charge
3978.51
-
-
Supply and fixing of flamed finished 30 mm thick Sadarhalli granite or approved equivalent on 1:4 cement slurry and pointing with approved color grout as per landscape architect's drawing including cut to required shape, pattern with paper joints, cost including all materials to site, all labour charges and other necessary tools and tackles etc complete and as directed by the Enigneer-in-Incharge
577.74
-
-
Providing edge moulding to 30 mm thick sadarhali/Granite stone using required machinery including machine polishing to edge to give gloss finish, conveyance of all materials, labour for all items of work, HOM of equipment etc. complete as per design & drawing and as approved by the Engineer in charge.
998.67
-
-
Supply and fixing of 230 mm x 50 mm x 14 mm Teracotta cladding tile set in 1:4 cement slurry and pointing with approved color grout as per landscape architect's direction cost including all materials to site, all labour charges and other necessary charges to complete for exposed faces of OAT seaters/feature walls/planter boxes etc., all as per drawing and as directed by the Engineer-in-Charge
345.53
-
-
Providing Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stoneaggregate) of 40mm thick finished with a floating coat of neat cement, including cement slurry, etc. complete and as directed by the Enigneer-in-Charge
2320.59
-
-
Providing Ceiling Plastering with CM 1:3, 6mm thick at all levels - Ceiling of buildings, staircse waist slab, sunshades, loft etc including scaffolding, curing etc all complete and as directed
9133.39
-
-
Providing 12 mm thick smooth / sponge finished plaster for internal and external surfaces with cement plaster of mix : 1:6 at all levels including scaffolding, curing etc all complete and as directed
11997.18
-
-
Providing and applying two coats of Distemper with Ist quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, including preparation of surface to remove all dirt, dust, mortar drops and other foreign matters, preparing the surface even, and sand paper smooth, cost of materials, labour, complete as per specification.
15577.11
-
-
Providing and applying two coats of acrylic emulsion with Ist quality acrylic emulsion, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, including preparation of surface to remove all dirt, dust, mortar drops and other foreign matters, preparing the surface even, and sand paper smooth, cost of materials, labour, complete as per specification.
5553.62
-
-
Providing and fixing stainless steel 304 grade for staircase railings,balconies, ramps, with hand rail of 1100mm high, 50mm dia 16 gauge hollow pipe welded to vertical pipe of 16 gauge stainless steel spaced at 0.9m regular intervals, and horizontal toughned glass panel of 12mm thick fixed as per the drawing and industry standards for satisfactory completion inlcuding fixing to concrete by using expansion bolts by drilling concrete etc, cost of all materials, labour, lead, lift, scaffolding at all levels and as directed by the Engineer in charge.
219.97
-
-
Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete at all levels and as per the direction of Enigneer-in-Charge
5840.1
-
-
Providing and appying polishing with French spirit polish on new wood surface and / or wood based surface to give an even surface after cleaning the surface of all dirt, dust and foreign matter, sand papered smooth, including cost of wood filler and materials, labour, complete as per the specifications
470.88
-
-
Supplying and fixing of Anjily wood wrought and put up for elevation frame work as per the drawing with lovers, including all materials and labour etc as required for satisfactory completion of owrk as per the drawing and as directed by the Engineer-in-Charge
45.27
-
-
Preparing the surface, providing and applying two coats of Synthetic Enamel paint of approved brand, quality, color etc. as per IS 2932 : 2003 after thoroughly sand papering the surfaces, removing the dust, dirt, repairing & filling dents, holes, cracks etc. over two coats of approved primer as per IS 2074 and one coat of paste filler to wall surfaces including cost of labour, materials, scaffolding, transportation, loading and unloading, tools & plants, all other incidental charges, etc. complete as per drawings, specifications at the following levels and as per the instructions of Engineer-in-Charge. The total painted thickness shall not be less than 100 microns DFT
6686.41
-
-
Providing and fixing Aluminium sliding doors with frame and shutter including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) all complete as per drawings and specifications and as directed by the Engineer-in Charge
25.2
-
-
Providing, fabricating & erecting Structural steel roof truss as per the drawing including anchoring the truss in RCC column using anchor bolts at each support. The work includes cutting, straightening, placing in position and welding wherever necessary and applying one coat of redoxide primer for all members including cost of all materials, labour charges and hire charges of machinery for cutting, welding, grinding and erection equipments, etc complete as per specification. Contract shall provide shop drawings for truss and all structural steel works before commencement of work and shall be approved by the Engineer-in-Charge.
232014.83
-
-
Providing & fixing on roof pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). The work includes all materials, labour, tools and tackles as required for satisfactory completion of work and as directed by Engineer-in-Charge
5443.76
-
-
Providing & laying on roof pressed clay tile ridge (Mangalore tile) of 20mm thickness and of approved pattern on steel frame work complete (steel frame work to be paid separately). The work includes all materials, labour, tools and tackles as required for satisfactory completion of work and as directed by Engineer-in-Charge
476.28
-
-
Supplying and fixing pull and push rolling shutters of approved make, made out of 18 gauge, 75mm wide cold rold steel laths of convex corrugation with side guides and bottom rail with interlocking arrangement for steel laths by means of alternate clips, suspension shaft with high tension coil type springs 2 numbers mounted on specially designed pipe shaft, with bracket plates, guide channels, ball bearing arrangements, for inside and outside locking with push and pull operation, complete including pulling hooks , 4 numbers handles with all fittings and accessories, painted with a coat of red lead paint with hood cover, cost of materials, labour, HOM of machinery complete as per specification.
15.12
-
-
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.
576.18
-
-
Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of:(i) Ist course of applying cement slurry @ 4.4 kg/Sq M mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.(ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixedwith water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.(iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per Sq M of area.(iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/Sq M).
110.11
-
-
Providing and laying pressed clay tiles (as per approved pattern 20 mm nominal thickness of approved size) on roofs jointed with cement mortar 1:4 (1 cement : 4 coarse sand) mixed with 2% integral water proofing compound, laid over a bed of 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand) and finished neat complete.
2320.59
-
-
Providing and fixing Laterite cladding with neatly dressed laterate stone of size 150mm x 300mm x 20mm thick using appropriate adhesive as required including all cost of materials, labour charges , Scaffolding etc. at all levels for satisfactory completion and as directed by the Engineer - in - charge
2260.71
-
-
Providing & fixing on roof ceiling with pressed clay tile (Mangalore tile) of 20 mm nominal thickness and of approved size and as per approved pattern on steel frame work complete (steel frame work to be paid separately). The work includes all materials, labour, tools and tackles as required for satisfactory completion of work and as directed by Engineer-in-Charge
5443.76
-
-
Supplying and Laying Mangalore tiles over the RCC roof jointed with neat cement slurry mixed with pigment to match the shade of tiles,including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand).
220.66
-
-
Fabricating, Supplying and Fixing bolcony handrails with square tube of 20mm &30mm and 40x10 mm as per the drawing including the cost for steel primer one coat and two coats of synthetic enamel paint, cutting , welding , grinding ,,etc all complete as required for satisfactory completion and as directed by Engineer - in - charge
29.54
-
-
Part - 2 Water supply , Internal plumbing, Sewer network, Sump & Over head tank
-
-
-
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc, not exceeding 80 mm dia
1396
-
-
Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil. and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia - All kinds of soil
433.55
-
-
Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m.
186.3
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sq M on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. - For all kinds of sump in all kinds of soil
2499.27
-
-
Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sq M on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. Ordinary rock
50.085
-
-
Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials. All kinds of soil
2315.64
-
-
Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials. Ordinary or hard rock
50.085
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
209.64
-
-
Providing and laying cast in situ cement concrete 1:4:8 including shuttering, form work, dewatering, compacting, curing etc complete - All work up to plinth level (1 Cement: 4 Sand: 8 graded stone aggregate 40mm size)
61.13
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Foundations, footings, bases of columns, etc. for mass concrete
135.43
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : walls including attached pilasters, buttersses, plinth and string courses etc
1095.61
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Suspended floors, roofs, landings, balconies and access platforms
470.94
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers
308.3
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Columns ( including circular), pillars, piers, abutments, posts and struts
390.38
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Stairs ( Excluding landings) except spiral staircase
29.66
-
-
Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 RM or part thereof (Plan area to be measured). For suspended floors, roofs, landings, beams and balconies
2446.8
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - upto plinth level.
46761
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - above plinth level at all levels
17881
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.- All works upto plinth level
488.43
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. - All works above plinth level upto floor V level
124.62
-
-
Providing M-30 grade concrete instead of M-25 grade BMC/ RMC as above
587.38
-
-
Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in CM 1:6 in basement and superstructure above plinth level up to floor V level in all shapes and sizes including all materials, labour charges, scaffolding, curing complete as per specification
48.41
-
-
Providing and constructing Laterite masonry with neatly dressed laterite stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor three level including all cost of materials, labour charges, scaffolding, curing etc.
2.45
-
-
Providing and fixing factory made uPVC wooden finish colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDMgasket, wool pile, zinc alloy (white powder coated) handle on one side ofextreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.
14.4
-
-
Providing and fixing 1 mm thick M.S. sheet door with frame and diagonal braces of size 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners with handle, stoppers and locking arrangements etc including applying a priming coat of red lead paint cost of materials, labour, HOM of machinery complete as per specification.
2.1
-
-
Supplying and fixing pull and push rolling shutters of approved make, made out of 18 gauge, 75mm wide cold rold steel laths of convex corrugation with side guides and bottom rail with interlocking arrangement for steel laths by means of alternate clips, suspension shaft with high tension coil type springs 2 numbers mounted on specially designed pipe shaft, with bracket plates, guide channels, ball bearing arrangements, for inside and outside locking with push and pull operation, complete including pulling hooks , 4 numbers handles with all fittings and accessories, painted with a coat of red lead paint with hood cover, cost of materials, labour, HOM of machinery complete as per specification.
9.4
-
-
Providing and laying Pigmented granolithic flooring of 52mm thick (which includes base concrete and top wearing coat 12mm thick in 1:6 (1 cement and 6 parts of 6mm down graded aggregate) in panels not more than 20 Sq M. in plan with cement concrete M20 grade by using coarse graded aggregate of 6 to 20 mm size, laid monolithic with floor concrete and finished smooth with power trowel including preparation of concrete surface and form work. The screed strips shall be fixed on the base concrete with 6 mm thick solid aluminium or other metals strips for effective separation of panels not exceeding 20 Sq M. in plan, unevenness in floor finish shall not exceed +2mm in Cum area, curing, grouting of lugs, etc. The rate shall include cost of materials, labour, tools & plants, loading and unloading, transportation, scaffolding and all other incidental charges etc., with all leads and lifts, complete as per specifications, drawings and as directed by the Engineer-in-charge
85.23
-
-
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.
828.12
-
-
Providing Ceiling Plastering with CM 1:3, 6mm thick at all levels - Ceiling of buildings, staircse waist slab, sunshades, loft etc including scaffolding, curing etc all complete and as directed
1033.24
-
-
Providing and applying two coats of Distemper with Ist quality acrylic distemper, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, including preparation of surface to remove all dirt, dust, mortar drops and other foreign matters, preparing the surface even, and sand paper smooth, cost of materials, labour, complete as per specification.
619.95
-
-
Providing and applying two coats of acrylic emulsion with Ist quality acrylic emulsion, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, including preparation of surface to remove all dirt, dust, mortar drops and other foreign matters, preparing the surface even, and sand paper smooth, cost of materials, labour, complete as per specification.
1527.21
-
-
Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, including all materials, labour, etc complete as per approved drawing & direction of Engineer-in-Charge.
4.32
-
-
Providing and fixing M.S. grills of required pattern in frames of windows etc.with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete at all levels and as per the direction of Enigneer-in-Charge
393.12
-
-
Preparing the surface, providing and applying two coats of Synthetic Enamel paint of approved brand, quality, color etc. as per IS 2932 : 2003 after thoroughly sand papering the surfaces, removing the dust, dirt, repairing & filling dents, holes, cracks etc. over two coats of approved primer as per IS 2074 and one coat of paste filler to wall surfaces including cost of labour, materials, scaffolding, transportation, loading and unloading, tools & plants, all other incidental charges, etc. complete as per drawings, specifications at the following levels and as per the instructions of Engineer-in-Charge. The total painted thickness shall not be less than 100 microns DFT
27.12
-
-
Excavating trenches of required width for pipes, cables, etc, including excavation for sockets, depth up to 1.5 m including getting out the excavated materials, returning the soil as required in layers not exceeding 20 cm in depth. including consolidating each deposited layers by ramming, watering etc., stacking serviceable material for measurements and disposal of unserviceable material as directed, within a lead of 50 m: Hard rock (requiring blasting) Pipes, cables etc. exceeding 80 mm dia but not exceeding 300 mm dia
1050
-
-
Providing and fixing white vitreous china wash basin size 630mm x 450mm with C.I. brackets, sensor pillar cock of 15mm, 32 mm C.P. brass waste of standard pattern and all necessary accessories, including painting of fittings and brackets, cutting and making good the walls wherever require:
58
-
-
Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre /8 litres), including seat cover, and cistern fittings, nuts bolts and gasket etc complete.
53
-
-
Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx.size 610x390x370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer - in-charge.
48
-
-
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm, necessary accessories, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink with drain board - 510 x 1040mm bowl depth 250mm
2
-
-
Providing and fixing toilet paper holder: CP brass
53
-
-
Providing and fixing mirror of superior glass ( of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : 1500 x 450mm
58
-
-
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms
58
-
-
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms
58
-
-
Supplying and fixing CP Health faucet of approved make including cost of materials and labour charges etc. complete as per the direction of Engineer-in-charge.
53
-
-
Providing and fixing Polyethelene - Aluminium - Polyethelene ( PE - AL- PE) Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80 °C including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) eg. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 meter spacing. This includes testing of joints complete as per direction of the Engineer -in-Charge. - 2532 ( 32mm OD) pipe
260
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. - 20mm nominal outer dia pipe
240
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. - 25mm nominal outer dia pipe
268
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. - 32mm nominal outer dia pipe
169
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work - 40mm nominal outer dia pipes
32
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work - 50mm nominal outer dia pipes
40
-
-
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching , refilling & testing of joints complete as per direction of Engineer- in-Charge. External work - 62.5mm nominal outer dia pipes
20
-
-
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: -20mm nominal bore
14
-
-
Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: -25mm nominal bore
10
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32mm nominal bore
16
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40mm nominal bore
2
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50mm nominal bore
22
-
-
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 62.5mm nominal bore
1
-
-
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 40 mm pipe 6Kgf/cm2
116
-
-
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 6 kgf/cm2
100
-
-
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 75 mm pipe 6 Kgf/cm2
337
-
-
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2
359
-
-
Providing and fixing trap of self cleansing design with screwed down or hinged grating without vent arm complete, including cost of cutting and making good the walls and floors: 100mm inlet and 100mm outlet - Sand cast iron S&S as per IS 3989
104
-
-
Providing and fixing brass bib cock of approved quality : 15mm nominal bore
15
-
-
Providing and fixing square-mouth S.W. gully trap class SP -1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:
8
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):
4
-
-
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design: Inside size 120x90 cm and 90 cm deep including C.I. cover with frame ( medium duty ) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg ( weight of cover 58 kg and weight of frame 58 kg):
2
-
-
Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12 mm dia steeel bar conforming to IS:1786, having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures permanent identification mark to be visible even after fixing including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 ( 1cement: 3 coarse sand: 6 graded stone aggregate 20 mm nominal size) Complete as per design
420
-
-
Supply, Installation, testing and commissioning of horizontal centrifugal pump (The cost should be inclusive for 2 Nos(1+1) of pump sets), of capacity 92 LPM Each Pump and 20 m head each and electric control panel board (Operating 1 pump at a time) with cyclic timer, dry run protection, required electrical and control wiring from panel to pump and also including supply and fixing the required butter fly valves, non return valves, Pressure gauge at each pump outlet of 150mm dial, 1/2" NPTM bottom connection, measuring element 316 SS diaphragm suitable to measure the discharge header pressure & pump discharge line pressure (0 to 10 kg/Sq cm) etc including the cost for the required length of pipes including the cost required for support for header pipes, discharge pipes for each pump and for common discharge pipes and including the cost for the required dismantling joints on either side of the pumps,as per manufacturer specifications etc complete and with all accessories like common base plate with suction and discharge manifold complete and as directed by the engineer in charge. (1 working and 1 standby)
2
-
-
Supply, Installation, testing and commissioning of horizontal centrifugal pump (The cost should be inclusive for 2 Nos(1+1) of pump sets), of capacity 100 LPM Each Pump and 23 m head each and electric control panel board (Operating 1 pump at a time) with cyclic timer, dry run protection, required electrical and control wiring from panel to pump and also including supply and fixing the required butter fly valves, non return valves, Pressure gauge at each pump outlet of 150mm dial, 1/2" NPTM bottom connection, measuring element 316 SS diaphragm suitable to measure the discharge header pressure & pump discharge line pressure (0 to 10 kg/Sq cm) etc including the cost for the required length of pipes including the cost required for support for header pipes, discharge pipes for each pump and for common discharge pipes and including the cost for the required dismantling joints on either side of the pumps,as per manufacturer specifications etc complete and with all accessories like common base plate with suction and discharge manifold complete and as directed by the engineer in charge. (1 working and 1 standby)
2
-
-
Supplying and laying of 50mm dia HDPE pipe, PE100 PN 16/10/8/6 as per IS 4984 U V stabilized & anti - microbial fusion welded, having thermal stability for potable & non potable water supply including specials, jointing ..etc complete as per specifications and as directed by the Engineer in Charge.
1396
-
-
Supplying and fixing of cast Iron, double flanged, manually hand wheel operated, Bolted Bonnet, Inside screw, Non rising spindle, Solid and taper wedge sluice valve (Gate valve) with pressure rating 10kg/sq.cm including HDPE drain pipe of diameter eqivalent to that of valve of about 6m length conforming to IS : 14846 - 2000 (Superseding IS : 780 -1984 and IS : 2906 -1984), PN – 10 with all jointing materials, gaskets, bolts, nuts, inclusive of dismantling pieces, washers, rubber gaskets as per IS:638 etc. complete as per direction of Engineer in Charge - Scour valve
4
-
-
Supplying and fixing of double orifice kinetic Air valve with isolating sluice valve confirming to IS 14845 damper proof design (PN;10) of approved quality with all jointing materials, gaskets, bolts, nuts, inclusive of dismantling pieces, washers, rubber gaskets as per IS:638 etc. complete as per direction of Engineer in Charge as per direction of Engineer in Charge - 40mm valve up to 100mm dia pipe
3
-
-
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for Scour valve/Air valve/Gate valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
25
-
-
Supplying and fixing ultrasonic level transmitter 0.65 to 5 m range - 24v, 50 KHz DC - 4 - 20 mA pulse output RS 485 communication and large display unit 6" height x 1' length consist of, transducer, transmitter cum local L C D indicator etc and suitable enclosure with I P 67 protection as per the standard. Suitable to measure the (0 to 5) meters, 4 to 20mA D.C Output. Complete with all hardware / accessories required for erection & commissioning. as per direction of Engineer in Charge.- (One no each for potable, Non potable and fire UG sump)
3
-
-
Providing and fixing gun metal non- return valve of approved quality (screwed
end) :Non potable water tapping for landscaping - 25 mm nominal bore
2
-
-
Providing and laying 100mm dia Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.
30
-
-
Providing and fixing enclosed type water meter 100mm dia (NB) (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately)
1
-
-
Construction of thrust blocks 0.3x0.3x1.15m in R.C.C 1:1.5:3 for HDPE. pipe and laying in position cement concrete with necessary excavation including centering and shuttering strutting, propping etc.
32
-
-
Providing and Laying 200mm dia (6kg/cm2) PVC pipes includings jointing of pipes with one step pvc solvent cement ,testing of joints complete as per direction of Engineer in Charge.
433.55
-
-
Constructing brick masonry circular type manhole 0.91 m internal dia at bottam and 0.56 m dia at to[ in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix ( 1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size ), and making necessary channel in cement concrete 1:2:4 ( 1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design: 0.91 m deep with S.F.R.C cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to IS: 12592, total weight of cover and frame to be not less than 182 kg, fixed in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately): With Sewer bricks conforming to IS:4885 Circular type manhole upto 0.91 m deep
11
-
-
Extra depth circular type manhole 0.91 m internal dia ( at bottom) beyound 0.91 m to 1.67 m
3.79
-
-
Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 ( 1 cement: 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 ( 1 cement: 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 ( 1 cement: 3 coarse sand: 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design: 1.68 m deep with SFRC cover and frame (heavy duty Hd- 20 grade designation) 560 mm internal diameter conforming to IS: 12592, total weight of cover and frame to be not less than 182 kg fixed in cement concrete 1:2:4 ( 1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. ( Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) With sewer bricks conforming IS:4885 Circular type manhole 1.22 m internal dia 1.68 m deep
7
-
-
Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m:
1.64
-
-
Supplying and fixing MS manhole ventilating shaft pipe of 200 mm at bottom and 100 mm at top to a height of 7.60 m confirming to IS 1239/3589 including earth work excavation, the cost for laying PCC in 1:2:4 using 20 mm hard broken stone over a finished layer of PCC 1:4:8 using 40 mm hard broken stone etc complete as per drawing
1
-
-
Supply ,erection and testing & commissioning of submersible gutter pump set ( in the lift manhole with a capacity of 0.5 lps @ 10m, total head with manufactures standard control panel provided with 1 m length of cable and as directed by the engineer in charge including other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts,GI nipple, etc completed and as directed by the engineer in charge.
2
-
-
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 50 mm pipe 10 kgf/cm2
10
-
-
Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of Nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate
305.1
-
-
Providing 12 mm thick smooth / sponge finished plaster for internal and external surfaces with cement plaster of mix : 1:6 at all levels including scaffolding, curing etc all complete and as directed
1496.92
-
-
Providing and laying 15mm smooth cement finished plaster in cement mortar 1:4 (1cement: 4 coarse sand) and adding Acco proof or Cicco or other approved water-proofing agent, 1 kg per bag of cement or as per manufacturer's specification, finished smooth in line, level and plumb including curing, scaffolding, hacking , raking joints etc. complete at all levels as directed and specified
14.975
-
-
Providing and fixing M.S. gratings of 1300mm dia for Manhole cover using MS angle 45x45x5mm alround and 20mm square spacing bars bothways at 100mm c/c including priming coat with approved steel primer all complete as per the drawing
1.33
-
-
Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality - H D - 20 - Circular shape 560 mm internal diameter
21
-
-
Supplying ,Providing and fixing in position of MS hand rail 1.00m height with top rail 32mm GI pie (NB) medium duty ,Mid rail 32mm dia, Vertical post 32mm dia at 600mm c/c including end plates, welding , applying priming coat of approved steel primer and as directed by the engineer in charge
76.94
-
-
Supply, erection and testing & commissioning of UV System Suitable for 2.02 cum/hr with necessary accessories etc.
1
-
-
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata,preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 RM depth below ground level.Rocky strata including boulders - 2 borehole each 80m - 300 mm dia
140
-
-
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS : 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer- in- Charge. - 200 mm nominal size dia
140
-
-
Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine /medium/coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer- in- charge.
5.5
-
-
Development of tube well in accordance with IS: 2800 (Part I) and IS : 1189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc.by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer - in-charge.
1
-
-
Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:
2
-
-
Providing and fixing Bail plug / Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS : 2800 (part I).
2
-
-
Providing and fixing M.S. clamp of required dia to the top of casing / housing pipe of tubewell as per IS : 2800 ( part I), including ecessary bolts & nuts of required size complete.
2
-
-
Supply, installation testing & commissioning of Cetrifugal pump set for the bore well capacity of 50LPM and max. total head of 100 m (Approximately 3.0 HP pump set) including cable 3 C, 4 sq.mm copper conductor pvc insulated cable suitable for submersible pump set operation and with manufacturer's standard control panel board which is mandatory and other required supporting items like SS hose nipple, nylon rope, clamps, bolt and nuts, GI nipple, hose of required length etc completed and as directed by the engineer in charge
3
-
-
Part - 3 Road, Stormwater drain, RWH & Compound wall
-
-
-
Filling with contractor own earth (excluding rock) in open areas in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m as per direction of site Engineer-in-charge.
52001.63
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sq M on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.
5853.69
-
-
Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials. All kinds of soil
1220.02
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.
3091.76
-
-
Earth work in excavation by mechanical means (Hydraulic excavator )/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sq M on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed. Ordinary rock
2126.38
-
-
Excavating trenches of required width for pipes, cables, etc including excavation
for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m,
including getting out the excavated soil, and then returning the soil as required,
in layers not exceeding 20 cm in depth, including consolidating each deposited
layer by ramming, watering, etc. and disposing of surplus excavated soil as
directed, within a lead of 50 m :
900
-
-
Disposal of excavated earth (excluding rock) and deposited in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
2126.38
-
-
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)
433.33
-
-
Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts,struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing :
1:1½:3 (1 cement : 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).
14.19
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Foundations, footings, bases of columns, etc. for mass concrete
6169.55
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : walls including attached pilasters, buttersses, plinth and string courses etc
5261.6
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Lintels, beams, plinth beams, girders, bressumers and cantilevers
33.12
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Columns ( including circular), pillars, piers, abutments, posts and struts
236.88
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - upto plinth level.
148431.66
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - above plinth level at all levels
55527
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.- All works upto plinth level
1557.41
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge. - All works above plinth level upto floor V level
669.52
-
-
Providing, hoisting and fixing above plinth level up to floor five level precast
reinforced cement concrete work in string courses, bands, copings,bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but, excluding cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) :3 graded stone aggregate 20 mm nominal size).
6.17
-
-
Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, Columns including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
62.91
-
-
Providing and laying in position machine batched and machine mixed design mix M-20 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.- All works upto plinth level
495.76
-
-
Providing and constructing Laterite masonry with neatly dressed laterite stone of size 40x20x15cm or nearest size in cement mortar 1:6 for super structure above plinth level up to floor three level including all cost of materials, labour charges, scaffolding, curing etc.
32.76
-
-
Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
302.1
-
-
Preparing the surface, providing and applying two coats of Synthetic Enamel paint of approved brand, quality, color etc. as per IS 2932 : 2003 after thoroughly sand papering the surfaces, removing the dust, dirt, repairing & filling dents, holes, cracks etc. over two coats of approved primer as per IS 2074 and one coat of paste filler to wall surfaces including cost of labour, materials, scaffolding, transportation, loading and unloading, tools & plants, all other incidental charges, etc. complete as per drawings, specifications at the following levels and as per the instructions of Engineer-in-Charge. The total painted thickness shall not be less than 100 microns DFT
23.85
-
-
Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. - Made of G.I. wire of dia. 4 mm, PVC coated to achieve outer dia not less than 5 mm in required colour and shade
152.36
-
-
Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.
746.63
-
-
Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.
746.63
-
-
Providing and fixing Shot blasted Grey coloured Flexi paver (450 mm x 400 m x 65 mm) set in CM 1:3. The work included cost of all materials such as pavers, Cement, sand etc., labour and equipment , cost of transportation lead, lift, loading and unloding to site, cleaning to the line and camber.
3231
-
-
Providing and fixing 65mm tkick Grey coloured interlock pavers , 200 mm x 100 mm as per selection paver from Basant Beton or equivalent using coarse sand for manufacture of blocks) of approved size and shape and colour with an average compressive strength of 281 kg/Sq M over sand bed 50mm avg . Thickness and compacting with vibrating plate compactor having 3 ton compaction force there by forcing part of sand underneath to come up in between joints. final compaction of paver surface to be done after spreading and brushing the fine sand into joints into its final level. The work included cost of all materials such as interlock pavers, sand etc., Labour and equipment such as cutting machine vibrating plate compactor, cost of transportation lead, lift, loading and unloading to site, cleaning to the line and camber.
414.37
-
-
Providing grill work in compound wall between columns with 50mm dia pipe horizontrally placed, 3 numbers of 50mm dia pipe vertically placed at equidistant between two columns, 32 x 8 mm MS flat frame with each member placed verically at 75mm c/c and welded to 50 mm dia pipe with 16mm dia rod including the cost for welding fixing in position complete as per the drawing
254.8
-
-
Providing and fixing Entry gate to 2 ISMC 75 on either side with 50 x 100 mm box section place vertically and horizontally to form a frame and 20 x 40 mm box section is welded to the frame in the pattern shown in the drawing
2
-
-
Providing and fixing 65mm tkick Terracotta coloured interlock pavers , 200 mm x 100 mm as per selection paver from Basant Beton or equivalent using coarse sand for manufacture of blocks) of approved size and shape and colour with an average compressive strength of 281 kg/Sq M over sand bed 50mm avg . Thickness and compacting with vibrating plate compactor having 3 ton compaction force there by forcing part of sand underneath to come up in between joints. final compaction of paver surface to be done after spreading and brushing the fine sand into joints into its final level. The work included cost of all materials such as interlock pavers, sand etc., Labour and equipment such as cutting machine vibrating plate compactor, cost of transportation lead, lift, loading and unloading to site, cleaning to the line and camber.
598.29
-
-
Providing and fixing 100 mm x 100 mm x 100 mm hammred finish black cobble stone paver set in Sand bed. The work included cost of all materials such as Cobble stones, Cement, sand etc., labour and equipment such as cutting machine vibrating plate compactor, cost of transportation lead, lift, loading and unloding to site, cleaning to the line and camber. (Black cobble stone)
98.76
-
-
Providing and fixing 500 mm x 500 mm x 40 mm PVC grass paver set in Sand bed. The work included cost of all materials such as Cobble stones, Cement, sand etc., labour and equipment such as cutting machine vibrating plate compactor, cost of transportation lead, lift, loading and unloding to site, cleaning to the line and camber.
3123.89
-
-
Providing and applying two coats of acrylic emulsion with Ist quality acrylic emulsion, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, including preparation of surface to remove all dirt, dust, mortar drops and other foreign matters, preparing the surface even, and sand paper smooth, cost of materials, labour, complete as per specification.
3388.78
-
-
Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm),including making drainage opening wherever required complete etc. as per direction edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).
67.44
-
-
Providing weep holes in stormwater drain with necessary 110mm dia pipe (6kg/m2),wire mesh screen ,necessary filling material etc complete as per direction of engineer in charge - 150mm wall
2402
-
-
Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 150 mm dia Elbow
80
-
-
Providing Rain water harvesting system as per the drawing including 300mm dia boring up to 4.0m depth, providing 200mm dia pvc pipes up to 4.0m, filling materials as specified, perforated precast cover slab etc, all complete and as directed.
7
-
-
Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 150 mm dia 6 Kgf/cm2 - External work- Exposed on wall
350
-
-
Providing and Laying 200mm dia (6kg/cm2) PVC pipes includings jointing of pipes with one step pvc solvent cement ,testing of joints complete as per direction of Engineer in Charge.
900
-
-
Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
34
-
-
Providing & Fixing of 10mm thick cement particle prelaminated board of preferred colour on top of Aluminium "L "sections of as support member anchord with proper screws and fasteners at regular intervals upon the walls/ Columns ..etc complete as per detailed drawing.
135.36
-
-
Part - 4 Fire alarm, Fire fighting, CCTV , Lift & Signages
-
-
-
Supplying, erecting, testing and commissioning of machine room less passenger Elevator having 10 passengers capacity of 680 Kgs, rated speed 1.0 mtr./sec., for GF, plus 1 upper floor, 2 openings, 400 volt 3 phase, 50 Hz, AC variable voltage variable frequency derive with speed encoding, simplex full collective with/with out attendant, microprocessor based controller located top floor, variable frequency regenerative drive, flat polyurethane coated belts for traction media, stainless steel panels with hairline finish for car and door, gearless with permanent magnet motor located in the shaft top, all openings are located at the front of the hoist way, with centre opening Automatic with ACVVVF door operator with electronic door protective system, stainless steel hairline finish sliding doors, painted frame with down light false ceiling, Stainless Steel mirror finish hand rails, granite flooring of client choice, sixteen segment digital LED display position indicator in all floors, digital car position indicator, over load warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby, with automatic rescue device, intercom between lift car and lobby and controller, voice synthesizer, 60 minutes fire rated car door. Car Entrance:- Clear opening 900 mm wide x 2100mm high etc., inclusive of all tax and duties
4
-
-
Supplying, erecting, testing and commissioning of machine room less passenger Elevator having 10 passengers capacity of 680 Kgs, rated speed 1.0 mtr./sec., for GF, plus 2 upper floor, 3 openings, 400 volt 3 phase, 50 Hz, AC variable voltage variable frequency derive with speed encoding, simplex full collective with/with out attendant, microprocessor based controller located top floor, variable frequency regenerative drive, flat polyurethane coated belts for traction media, stainless steel panels with hairline finish for car and door, gearless with permanent magnet motor located in the shaft top, all openings are located at the front of the hoist way, with centre opening Automatic with ACVVVF door operator with electronic door protective system, stainless steel hairline finish sliding doors, painted frame with down light false ceiling, Stainless Steel mirror finish hand rails, granite flooring of client choice, sixteen segment digital LED display position indicator in all floors, digital car position indicator, over load warning indicator, battery operated alarm bell and emergency light, fireman's switch at main lobby, with automatic rescue device, intercom between lift car and lobby and controller, voice synthesizer, 60 minutes fire rated car door. Car Entrance:- Clear opening 900 mm wide x 2100mm high etc., inclusive of all tax and duties
2
-
-
Supply, installing, testing and commissioning of Microprocessor based intelligent addressable, modular, expandable networkable, multiloop panel fire alarm control panel with Liquid Crystal Display, multiple access levels with historic event. The panel shall support programmable relays for controlling lifts, AHU's, ventilation fans, fire pump, monitoring of fire sprinkler and fire hydrant pumps. The panel shall have 240 volts AC power supply, automatic battery charger, 24 volts, sealed lead acid maintenance free batteries sufficient for 24 hours normal working and then be capable of operating the system for 60 minutes during emergency condition. The panel shall be Approved to UL Standards should be capable of being integrated into third party PA system
2
-
-
Supply, installing, testing and commissioning of Microprocessor based intelligent addressable, modular, expandable networkable, 1 loop card suitable to accodomate 128 devices per loop multiloop panel fire alarm control panel with Liquid Crystal Display, multiple access levels with historic event. The panel shall support programmable relays for controlling lifts, AHU's, ventilation fans, fire pump, monitoring of fire sprinkler and fire hydrant pumps. The panel shall have 240 volts AC power supply, automatic battery charger, 24 volts, sealed lead acid maintenance free batteries sufficient for 24 hours normal working and then be capable of operating the system for 60 minutes during emergency condition. The panel shall be Approved to UL Standards should be capable of being integrated into third party PA system
1
-
-
Supply, installing, testing and commissioning of Microprocessor based repeater panel suitable for addressable fire alarm system to be located at Administration building. The panel shall be Approved to UL Standards should be capable of being integrated into third party PA system
1
-
-
Optical Smoke detector
205
-
-
Rate of rise heat detector
2
-
-
Supply, installing, testing & commissioning of addressable Manual call point .
52
-
-
Supply, installing, testing and commissioning of Loop Powered dual tone hooters cum Strobe, built-in Power Supply & Modules
11
-
-
Supply, installing, testing and commissioning of Loop Powered dual tone hooters , built-in Power Supply & Modules
19
-
-
Supply, installing, testing & commissioning of addressable isolator with necessary back box and accessories.
18
-
-
Supply, installing, testing and commissioning of addressable and automatic commandable control modules with built in power supply
3
-
-
Supply, installing, testing and commissioning of Response Indicator
104.5
-
-
Supplying and fixing of following sizes 20 mm, 1.5 mm thick PVC conduit along with accessories in concealed and drawing following sizes of FR PVC insulated copper conductor, dual core cable in the existing surface/ concealed, steel/ PVC conduit/ PVC casing capping as required.
(a) 2c x 1.5 sq. mm unarmoured cable
5235
-
-
Supplying, erecting, testing and commissioning fire hydrant pump Horizontal Centrifugal End Suction capable of delivering 2850 lpm at 50 mtr head complete with adequate HP automatic diesel engine driven pumps having the residential silencer system and other accessories list tuel tank, necessary cooling system .
1
-
-
Supply, erection, testing and commissioning of single stage Horizontal centrifugal End Suction pumps, of approved make for giving discharge of 2850 lpm at a pressure of 50 mtr directly coupled to suitable TEFC motor to operate 400/440 volts 3 phase 50 cycles AC supply tih a terminal box suitable for the reception common base plate, necessary foundation bolts.
2
-
-
Supply, erection, testing and commissioning of centrifugal Jockey Pump of approved make, which gives a discharge of 180 lpm at 50 mtr head, with suitable electrical driven motor directly coupled to suitable HP TEFC motor to operate 400/440 volts 3 phase 50 cycles AC supply with terminal box suitable for the reception common base plate, necessary foundation bolts. 7.5hp
1
-
-
Supply, storing, erection, testing and commissioning of automatic motor control panel comprising generally of the following and fabricated as per specification
a. Incoming TPN SFU with fuses b. Aluminum bus bar as per specification c. TPN MCCB outgoing leader with fuses for jockey pumps d. TPN MCCB outgoing feeder for main electric pump
e. Voltmeter 96mm (0-500 V ) with selector switch and protection fuses for incomer f. Starter for jockey pump with single phase preventor, automatic pressure switch starting arrangement indicating lamps, fuses and resistors g. Starter for main electric pump with motor protection relay selector switches, ammeters, CTS, Jockey pump and automatic pressure switch starting arrangement , MCBs for control circuits (Hydrant).
i. Audio visual alarm system and necessary indicating lamps.
j. Minimum length of 500mm required for cable termination.
1
-
-
Supply, storing, erection, testing and commissioning of wall mounted 24 volts control panel to start the fire pump engine automatically as per the following sequence of operation and the auxiliary arrangements a. Engine to start automatically in case of low water pressure secured by the pressure switch with necessary timers relays etc b. Manual stopping c. Audio visual alarm for fault
d. Low fuel oil level e. Engine lover speed f. High water temperature g. Low type oil pressure h. Engine false to start i. A battery charger with trickle / Boost arrangements with secondary side tapping at 28, 30,32 and 34 volts equipped with silicon diodes to charge the starting battery of the diesel engine
1
-
-
Supply, fixing, and commissioning of Butterfly Valves as per IS 780/Gate valve as per with flanged ends. The valve has to be fixed using bolts , nuts , washer & rubber gasket 150mm dia
16
-
-
Supply, fixing, testing and commissioning of gun metal Ball valves with wheel complete as required. 50mm dia
2
-
-
Supply, fixing, testing and commissioning of Non-return valve(Water Check valves) as per IS 5132 complete with hand wheel, companion flange, nuts, gaskets, bolts etc complete as required. 150mm dia
4
-
-
Providing & Fixing Y-Strainer GI complete with stainless steel bucket having 0.3mm perforation, flanged ends, filteration area 1:4,PN 16 rating, complete etc.
150mm dia
2
-
-
Test array arrangement for pumpset with pressure gauge & Pressure Switch , valves etc.
Presure Switch
4
-
-
Test array arrangement for pumpset with pressure gauge & Pressure Switch , valves etc.
Pressure Gauge
5
-
-
Supply, fixing, testing and commissioning of air vessel tank of size 300mm dia x 1000mm long with necessary inlets, outlets, etc complete as per detailed specifications.
1
-
-
a. 63mm dia Gun metal instantaneous 4 way inlet arranged on a 150mm dia GI header with flanges & b. 1 no. 150mm Butterfly Valve for Hyd system
1
-
-
Supply, erection, testing and commissioning of heavy C class MS pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete (Above Ground) 150mm dia
60
-
-
Supply, erect, jointing, testing and commissioning MS Heavy C class in trenches (1 Mtrs below ground level). Rate quoted shall include for necessary specials like long radius bends, tees including cutting, welding, flanged joints with necessary washers, nuts, bolts etc. Rate quoted shall also include for providing concrete anchor blocks at all change in direction of pipeline and also near each joints and giving anticorrosive treatment as per specification. Including cost for excavation & refilling. (Under Ground )
150mm dia
55
-
-
Providing, Laying, Testing and commissioning of 250 mm dia RCC pipes of NP2 class hume pipes
55
-
-
Supply and installation of Cast Iron Butterfly valve including making flanged joints by providing necessary nuts, bolts, gaskets(1.5 mm CAF)etc. All complete as per specification.
2
-
-
Supply and installation of Cast Iron Non - Return Valve including making flanged joints by providing necessary nuts, bolts, gaskets etc. All complete as per specification.
1
-
-
Supply and installation of 'Y' Strainer including making flanged joints by providing necessary nuts, bolts, gaskets etc. All complete as per specification.
1
-
-
Supply, fixing, testing and commissioning of Yard Hydrant system with necessary accessories etc,. and the following
a. 63 mm dia single head landing valve (Stainless Steel)
17
-
-
Supply, fixing, testing and commissioning of Yard Hydrant system with necessary accessories etc,. and the following b. Hose pipe 63 mm dia 15 m.long with male and female coupling at both ends
34
-
-
Supply, fixing, testing and commissioning of Yard Hydrant system with necessary accessories etc,. and the following c. Branch pipe 63 mm dia with 20 mm (nominal internal diameter) nozzle and suitable for instaneous connection
17
-
-
Supply, fixing, testing and commissioning of lever operated slim seal butterfly valves as per detailed specifications complete with Tamper switch, companion flange, nuts, gaskets, bolts etc complete as required. 150mm dia
17
-
-
Supply, erect, jointing, testing and commissioning MS Heavy C class in trenches (1 Mtrs below ground level). Rate quoted shall include for necessary specials like long radius bends, tees including cutting, welding, flanged joints with necessary washers, nuts, bolts etc. Rate quoted shall also include for providing concrete anchor blocks at all change in direction of pipeline and also near each joints and giving anticorrosive treatment as per specification. Including cost for excavation & refilling. (Under Ground )
150mm dia
835
-
-
Supply, erection, testing and commissioning of heavy C class MS pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete (Above Ground) 80mm dia
25.5
-
-
Providing, Laying, Testing and commissioning of 250 mm dia RCC pipes of NP2 class hume pipes
68
-
-
Supply, erection, testing and commissioning of heavy C class MS pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete 150mm dia
105
-
-
Supply, erection, testing and commissioning of heavy C class MS pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete 50mm dia (DRAIN LINE)
55
-
-
Supply, erect, jointing, testing and commissioning MS Heavy C class in trenches (1 Mtrs below ground level). Rate quoted shall include for necessary specials like long radius bends, tees including cutting, welding, flanged joints with necessary washers, nuts, bolts etc. Rate quoted shall also include for providing concrete anchor blocks at all change in direction of pipeline and also near each joints and giving anticorrosive treatment as per specification. Including cost for excavation & refilling. 150mm dia
1061.5
-
-
Supply, fixing, testing and commissioning of lever operated slim seal butterfly valves as per detailed specifications complete with Tamper switch, companion flange, nuts, gaskets, bolts etc complete as required. 150mm dia
4
-
-
Supply, fixing, testing and commissioning of the following Single Hydarnt valve (SS)
17
-
-
Supply, fixing, testing and commissioning of the following RRL hose filled with SS couplings of 15 mtr long
34
-
-
Supply, fixing, testing and commissioning of the following Supply of SS branch pipe
17
-
-
Supply, fixing, testing and commissioning of the following Hose reel Drum with Hose Reel of 36 mtr and spray nozzle
17
-
-
Supply, fixing, testing and commissioning of the following MS Hose Tray
17
-
-
Supply and fix Internal glass fronted duct Door with hinged and lock, made out of 16 Aluminium powder coated(po red) sheet of suitable size to accommodate the following
17
-
-
Supply & fixing of air release valve at the top of each floor of the riser with drain connection and the rates shall include all the accessories
7
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
150mm dia
60
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete
100mm dia
38.5
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
80mm dia
22
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
65mm dia
27.5
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
50mm dia
28.05
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
40mm dia
35.2
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
32mm dia
10
-
-
Supply, erection, testing and commissioning of C class GI pipes . The pipes being fixed on to the wall or suspended from the ceiling / truss with angle iron supports complete with bends, tees, flanges and with all other required accessories including painting of the pipeline with two coats of approved enamel paint over a coat of primer etc complete.
25mm dia
154
-
-
Supply, fixing, testing and commissioning of lever operated slim seal butterfly valves as per detailed specifications complete with Tamper switch, companion flange, nuts, gaskets, bolts etc complete as required. 100mm dia
7
-
-
Supplying, Installing, testing and commissioning of Test & Drain valve of size 50mm.
4
-
-
Supplying, Installing, testing and commissioning of 150mm Installation Control Valve with gong, bell, trim & complete kit.
4
-
-
Supplying, Installing, testing and commissioning of Standard Response Upright, Pendent & side wall sprinkler, 1/2" orifice, 1/2" BSPT end connection, 68 deg , Celsius, chrome finish.
158
-
-
Supplying, Installing, testing and commissioning of flow switch installed on the sprinkler main distribution line connected to the main sprinkler annunciation panel located in the ground floor.
1
-
-
Supplying, Installing, testing and commissioning of SS ball valve of size 25mm dia for flushing purpose.
8
-
-
Supplying, Installing, testing and commissioning of zone annunciation panel located in the ground floor.
1
-
-
Supply, Installation, Testing & Commissioning of 4 Kg Capacity of ABC type fire extinguisher fixing on the floor with suitable fixture.
31
-
-
Supply, Installation, Testing & Commissioning of 4.5 Kg capacity of CO2 type fire extinguisher fixing on the floor with suitable fixture.
14
-
-
Supply, installation, testing, commissioning of approved make 2MP IP Dome Camera indoor type of approved make including necessary mounting clamps and appropriate accessories as required for satisfactory completion
60
-
-
Supply, installation, testing, commissioning of approved make 2MP IP PTZ Camera with Bracket outdoor type of approved make including panel tilt mechanism, necessary mounting clamps and appropriate accessories as required for satisfactory completion
6
-
-
Supply, installation, testing, commissioning of approved make 2MP IR IP H.265 Bullet camera with 2.8 to 12mm Motorized Lens, POE, SD card sLot, WDR, Smart Analytics and 50M IR support all inclusive for satisfactory completion
9
-
-
Supply, installation, testing, commissioning of approved make 64 Channel NVR including all accessories as required for satisfactory completion
1
-
-
Supply, installation, testing, commissioning of approved make 6TB HDD including all accessories as required for satisfactory completion
6
-
-
Supply and fixing of 15U wall mount rack with tray and cable manager including all accessories as required for satisfactory completion
2
-
-
Supply and fixing of 6U wall mount rack with tray and cable manager including all accessories as required for satisfactory completion
6
-
-
Supply and fixing of Camera BackBox
75
-
-
Supply, installation, testing, commissioning of approved make 8 Port POE Switch with SFP Module
3
-
-
Supply, installation, testing, commissioning of approved make 24 Port POE Switch with SFP Module
3
-
-
Supply, installation, testing, commissioning of approved make PTZ Pole with fixing
9
-
-
Supply and laying of Category 6 U/UTP 4 Pair 23AWG Cable with suitable PVC Conduit
6300
-
-
Supply and laying of Category 6 U/UTP 4 pair Outdoor cable PE with suitable PVC Conduit
675
-
-
Supply, installation, testing, commissioning of approved make 24 Port Patch Panel
4
-
-
Supply, installation, testing, commissioning of approved make Patch Chord 1 M
84
-
-
Supply, laying, testing, commissioning of approved make 6 Core Multimode OFC Cable with required end splising, and termination and OFC to RS 485 converters etc., as required laid in suitable surface / concealed PVC conduit as required including all accessories as required.
600
-
-
Supply, installation, testing, commissioning of approved make 6 Port Loaded LIU
4
-
-
Supply, installation, testing, commissioning of approved make 12 Port Loaded LIU
3
-
-
Supply, fixing of approved make Patch Cord - Multimode
6
-
-
Supply installation testing and commissioning of 42" LED display with necessary mounting arrangements
2
-
-
Supply, installation, testing, commissioning of approved make Single Lane - Dual Point of Entry Features: 24/7 Surveillance Protection Real-time Detection Number Plate Recording as (1) Images (2) Database Reports for (1) Entry / Exit Times (2) Frequencty of Visits (3) Lean / Peak time analysis Black List / White lists Overstay Parking Alert
1
-
-
Supply, installation, testing, commissioning of approved make 6W Ceiling Speaker including all accessories as required.
85
-
-
Supply, installation, testing, commissioning of approved make 700W Amplifier suitable for 230 volts operation including all accessories as required.
1
-
-
Supply, installation, testing, commissioning of approved make Paging Microphone including all accessories as required.
1
-
-
Supply, installation, testing, commissioning of approved make USB Kit including all accessories as required.
1
-
-
Supply and fixing of 2 Core X 1.5sq mm Armoured Cable with suitable PVC Conduit concealed/surface mounted as required including all accessories required for satisfactory completion and as directed by the Engineer-in-Charge
600
-
-
Supply, installation, testing, commissioning of approved make BGM player including all accessories as required.
1
-
-
LSG1-Gate Way main Entrance
Made in 100 x 50 mm square pipe frame work letters enclosed in 4mm thick ACP sheet panels with back side LED light and fixing on site(civil work will be extra)
size:
1
-
-
LSG2- Directional signage Made in 150mm to 75mm reducible pol 2mm thick Mild steel sheet with with light grey MRF coating & all letters 3Mvinyl cut letters panels fixing (civil work will be extra)
size:3.2mtr H x 0.15mtr W
4
-
-
LSG3- Pedestrian Map signage
Made in 150 x 50 mm square pipe frame work with 4mm thick ligt grey colour ACP sheet panels with 3M Eco solvent print and fixing on site(civil work will be extra)
size:2.4mtr H x 0.9mtr W
2
-
-
LSG4-A-Information plaque-Type-1
Made in 150 x 50 mm square pipe frame work with 4mm thick ligt grey colour ACP sheet panels with 3M Eco solvent print and fixing on site(civil work will be extra)
size:2.4mtr H x 0.9mtr W
6
-
-
LSG5- Plaza of fame bollards
Made in 50 x 50 mm square pipe frame work with 4mm thick ligt grey colour ACP sheet panels with 3M Eco solvent print and fixing on site(civil work will be extra)
size:1.8mtr H x 0.2mtr W
18
-
-
LSG6-History wall
Made with letters and graphics with exterioir paint on site
90
-
-
LSG7-Platforms for Artwork
Made in 600x600 x 450 mm Granite stone cube to finished with 2 layers of hand chiselling inclusive of fixing on site(Base civil work will be extra)
10
-
-
PART - 5 Landscape & Horticulture
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sq M on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.
629.95
-
-
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
346.47
-
-
Granular Sub base course -Providing and laying Granular Sub base course of 150 mm layer machine crushed black trap Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.
34.12
-
-
Providing and laying cast in situ Cement concrete 1:4:8 including shuttering, form work, dewatering, compacting, curing etc complete - All work up to plinth level (1 Cement: 4 Sand: 8 graded stone aggregate 40mm size)
115.53
-
-
Providing and laying in position reinforced cement concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20mm and down gauge) including cost of reinforcement, centring, shuttering and reinforcement and cured complete.
85.76
-
-
Providing and fabricating HYSD Steel reinforcement including straightening, cutting, bending, hooking, lapping and/or welding wherever required, placing in position tieing with binding wire of approved quality and gauge including the cost of binding wire and anchoring to the adjoining members where ever necessary including all laps and wastages etc,complete as per design and specification .
2000
-
-
Random rubble masonry with Cement mortor 1:6 hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortor 1:6
62.08
-
-
Providing and constructing pre cast concrete solid block (Factory made) with compressive strength not less than 35kg/Sq M with cement mortar 1:4 masonry with solid concret blocks of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for foundation & plinth up to floor three level including cost of materials, labour charges, scaffolding, curing complete as per specification.
105.49
-
-
Solid block masonry using pre cast solid blocks ( Factory made) of size 40x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for foundation and plinth with thickness 15 cm in : CM 1:6 ( 1 cement : 6 coarse sand ) etc complete
20.69
-
-
Laterate masonry with neatly dressed laterate stone of size 40x20x15cm or nearest size in cement mortar 1:6 for foundation and basement including all cost of materials, labour charges etc.
6.6
-
-
Providing and laying Plain cement concrete 1:3:6 for copings of following to the specified depth using graded granite aggregate of 40mm and down size, including mixing, compacted by wooden or cast iron rammers, curing etc., complete.
7.76
-
-
Providing and laying 15mm smooth cement finished plaster in cement mortar 1:4 (1cement: 4 coarse sand) and adding Acco proof or Cicco or other approved water-proofing agent, 1 kg per bag of cement or as per manufacturer's specification, finished smooth in line, level and plumb including curing, scaffolding, hacking , raking joints etc. complete at all levels as directed and specified
275.93
-
-
Providing and finishing by pressing the mortar into the raked out joints, with a pointing trowel, either flush, sunk or raised, according to the type of pointing required for exposed faces of Laterite stone masonry wall in CM I:6 with water proof treatment for joints. The mortar shall not spread over the corner, edges or surface of the masonry. The pointing shall then be finished with the proper tool, in the manner described below for flush Pointing . The mortar shall be pressed into the joints and shall be finished off flush and level with the edges of the stones so as to give a smooth appearance. The edges shall be neatly trimmed with a trowel and straight edge
39.6
-
-
Providing and painting with Exterior grade paint for external walls with approved make and shade thoroughly sand papering the surfaces. removing, dirt, dust, repairing dents. holes, cracks,applying following grade paint . as per specifications.including consumables such as blades , rollers , brushes, including the cost of painting material and labour charges for scaffolding etc. at all levels for walls of Green room planters etc.,
275.93
-
-
Supplying , Installing & Commissioning the 1 HP Single phase Submersible Pump Code KOS 116M, Head 8 mts, 4.9 LPS with all complete specifications inclusive of cost of transportation etc complete including 32mm dia CPVC pipe, pump of required capacity and valves etc as required for satisfactory completion of works and as directed.
1
-
-
Providing and laying Granite (Grey) flooring 30mm thick with flammed finish of size 600mm x 900mm, and fixing as detailed in drawing with 4mm spacer set in CM cement mortar 1:4 over a PCC inclusive of filling of joints with epoxy gout etc and necessary cleaning activites for joint filling etc, complete and as directed by Engineer-in-Charge
744.02
-
-
Supply and fixing of flamed finished 30 mm thick Sadarhalli granite or approved equivalent on 1:4 cement slurry and pointing with approved color grout as per landscape architect's drawing including cut to required shape, pattern with paper joints, cost including all materials to site, all labour charges and other necessary tools and tackles etc complete and as directed by the Enigneer-in-Incharge
200.96
-
-
Providing edge moulding to 30 mm thick sadarhali/Granite stone using required machinery including machine polishing to edge to give gloss finish, conveyance of all materials, labour for all items of work, HOM of equipment etc. complete as per design & drawing and as approved by the Engineer in charge.
383.83
-
-
Providing and laying Burnt stone slab in crazy pattern of 75 mm thick rough chisel dressed and cut as per design and drawing, on 50 mm thick sand bed and to be pointed with 50 mm thick grass joints inclusive of wastage, lead and lift, soil filling for lawn planting in joints as per required size and pattern, finishing and sweeping extra sand etc. complete as per manufacturer's specifications & direction of Engineer-in-Charge.
389.4
-
-
Supply of White pebble tumbled finished of 35mm to 75 mm of size laid loose on sand / PVC Sheet / Geofabric as required by site conditions, in min 2 to 3 layers in a manner that it blocks the visibility of ground as approved by architect inclusive of cost of transportation etc complete
3408.89
-
-
Supply of SS Jalli made out of 306 grade 12 gauge perforated SS sheets and 25x25x5 ms angle frame @ 400mm c/c welded inclusive of provision for light fixtures etc complete
5.5
-
-
Supply of White pebble tumbled finished of 35mm to 75 mm of size laid loose on sand / PVC Sheet / Geofabric as required by site conditions, in min 2 to 3 layers over water body as approved by architect inclusive of cost of transportation etc complete
367.86
-
-
Supply and fixing of 230 mm x 50 mm x 14 mm Teracotta cladding tile set in 1:4 cement slurry and pointing with approved color grout as per landscape architect's direction cost including all materials to site, all labour charges and other necessary charges to complete for exposed faces of OAT seaters/feature walls/planter boxes etc.,
579.18
-
-
Cleaning and Digging up existing ground to a depth of 150 mm , excavation of unwanted soil / debris and carting out of site and formation of ground wrt dwaing etc complete
16009.28
-
-
Consolidation of existing soil for the mounds to the required height as per the design and as directed.
200
-
-
Supply and spreading garden soil mix to a depth of 300mm. Planting area and shall be filled with Garden soil(to be brought from outside). Quantity of material brought shall be measured as executed at site and shall be the basis of measurement. There shall be no deductions for voids. However it is the responsibility of contractor to ensure that the quantity of soil media does not exceed the theoretically computed quantity in BOQ. There should not be a need to increase the quantity beyond earlier budget, the contractor should get written permission from client before proceeding clearly indicating the reasons for the increase.
2227.59
-
-
Supply and spreading garden soil mix with 40% coco-pit to a depth of 300mm. Planting area and shall be filled with Garden soil(to be brought from outside). Quantity of material brought shall be measured as executed at site and shall be the basis of measurement. There shall be no deductions for voids. However it is the responsibility of contractor to ensure that the quantity of soil media does not exceed the theoretically computed quantity in BOQ. There should not be a need to increase the quantity beyond earlier budget, the contractor should get written permission from client before proceeding clearly indicating the reasons for the increase.
393.1
-
-
Manure - ORGANIC Supply of Farm yard Manure /vermicopost/Organic Manure (For Plants& Trees)
262.07
-
-
Manure - ORGANIC Supply of neem cake (1.5kg/1 sq.mt)
9569.33
-
-
Supply Manure - INORGANIC To be applied one month after planting. Supply of Fertilizer (NPK) 15-15-15 (500gms/Sq M)
3189.78
-
-
Supply and filling of landscape grade Clay in the water body to a depth of 450 mm for growth of aquatic plants
8.39
-
-
Planting of Trees with pits of size 600 mm x600 mm x600 mm filled with a mixture of garden soil required as per specification separately indicated , Rate to include labour charges for pitting, mixing Soil media ( Garden soil , Sand and Manure ) , filling the pits with Soil media, planting the sapling and maintenance for a period as per conditions of agreement from the date of completion of planting. (Rate should not include Supply of Sappling, Garden soil, Sand and Manure which should be separately quoted
1233
-
-
Planting of big Shrubs (Without Plants)
Planting of Shrubs spreading garden soil as per specification, over graded surface to attain a total depth of 300 mm from the graded surface. Rate to include labour charges for mixing Soil media ( garden soil , Sand and Manure) , planting the sapling* and maintenance for a period as per conditions of agreement from the date of completion of planting.(Rate should not include supply of Sapling, Garden soil, Sand and Manure which should be separately quoted*
Planting of Shrubs in staggered pattern of 2 rows covering width upto 0.6 mts @ 5 Nos per RM or 7 Nos per Sq M for polygon shape plantation
6125
-
-
Planting of Small Shrubs and Climbers(Without Plants)
Planting of Shrubs spreading garden soil as per specification, over graded surface to attain a total depth of 300 mm from the graded surface. Rate to include labour charges for mixing Soil media ( garden soil , Sand and Manure) , planting the sapling* and maintenance for a period as per conditions of agreement from the date of completion of planting.(Rate should not include supply of Sapling, Garden soil, Sand and Manure which should be separately quoted)*
Planting of Shrubs in staggered pattern of 2 rows covering width upto 0.45 mts @ 7 Nos per RM or 13 Nos per Sq M for polygon shape plantation
5415
-
-
Mexican Lawn in Horticulture area - Carpet laying
Supply and fixing of Mexican Lawn: a)Mixing,spreading and Grading of Garden Soil ,Manure and Sand in the Ratio of 2:1:1, finished with anti termite chemical (Rate should not include supply of Garden soil, Sand and Manure, Planting material), Planting by Carpeting method and Maintaining the planted turf for a period as mentioned in agreement from date of Planting inclusive of rolling / hand ramming, top dressing with Mexican species and periodic leveling of surface with sand and organic manure etc complete
1117.26
-
-
PLANTS ASSOCIATED WITH ONAM
-
-
-
Bauhinea Alba
22
-
-
Clerodendrum paniculatum
15
-
-
Hibiscus rosa-sinensis
75
-
-
Ixora coccinea
100
-
-
Aerva lanata
25
-
-
Biophytum sensitivum
20
-
-
Cardiospermum halicacabum
20
-
-
Curculigo orchioides
20
-
-
Cyanthillium cinereum
20
-
-
Cynodon dactylon
30
-
-
Eclipta prostrata
20
-
-
Emilia sonchifolia
20
-
-
Evolvulus alsinoides
20
-
-
Ipomoea
20
-
-
Ceylon Slitwort
30
-
-
Clitorea Ternatea
15
-
-
Lantana camara
100
-
-
Lucas Aspera
95
-
-
Ocimum tenuiflorum
75
-
-
Calendula officianalis
75
-
-
NAVAGRAHA VANA, RASHI VANA AND NAKSHATRA VANA
-
-
-
Achyranthus aspera
1
-
-
Ficus racemosa
2
-
-
Butea moNosperma
3
-
-
Ficus religiosa
3
-
-
Acacia catechu
3
-
-
CaLotropis procera
1
-
-
Prosopis cenneraria
2
-
-
Pterocarpus santalinus
1
-
-
Alstonia scholaris
1
-
-
Artocarpus Heterophyllus
2
-
-
Stereospermum chelonoides
1
-
-
Mangifera indica
2
-
-
Mimusops elengi
1
-
-
Dalbergia sissoo
1
-
-
Ficus bengalensis
2
-
-
Adhatoda vasica
1
-
-
Phyllanthus emblica
1
-
-
Syzygium cumini
1
-
-
Terminalia belerica
1
-
-
Bambusa arundinacea
1
-
-
Calophyllum inophyllum
1
-
-
Ficus arnottiana
1
-
-
Aegle marmelos
1
-
-
Terminali arjuna
1
-
-
Mammea suriga
1
-
-
Bombax ceiba
1
-
-
Acacia arabica
1
-
-
Saraca ashoca
1
-
-
CaLotropis gigantea
1
-
-
Prosopis glandulosa
1
-
-
Neolamarckia Cadamba
1
-
-
Azadirachta indica
1
-
-
Madhuca latifolia
1
-
-
Imperata cylindrica
75
-
-
Jasminum officinalis
250
-
-
ENDANGERED SPECIES
-
-
-
Aglaia malabarica
1
-
-
Dialium travancoricum
1
-
-
Dipterocarpus bourdillonii
1
-
-
Syzygium palghatense
1
-
-
Vateria macrocarpa
1
-
-
SCARED GROVES
-
-
-
Aegeles marmalos
25
-
-
Alstonia scholaris
25
-
-
Antiaris toxicaria
25
-
-
Artocarpus hirsutus
15
-
-
Azadiractha Indica
25
-
-
Cassia fistula
35
-
-
Ficus bengalensis
10
-
-
Ficus Religiosa
10
-
-
Garcinia cambogia
35
-
-
Garcinia Indica
40
-
-
Holigarna arnottiana
15
-
-
Hopea parviflora
15
-
-
Hopea ponga
25
-
-
Hydnocarpus pentandra
15
-
-
Mangifera indica
15
-
-
Mesua ferrea
25
-
-
Mimusops elengi
25
-
-
Phyllanthus emblica
35
-
-
Saraca Indica
35
-
-
StrychNos nux-vomica
25
-
-
Syzygium Cumini
15
-
-
Vateria indica
10
-
-
Chassalia curviflora
70
-
-
Ixora nigricans
70
-
-
Carissa Carandas
75
-
-
Acacia intsia
10
-
-
Anamirta cocculus
10
-
-
Asparagus racemosus
10
-
-
Calycopteris floribunda
10
-
-
Gloriosa superba
10
-
-
Ipomoea alba
10
-
-
Moullava Spicata
10
-
-
Piper longum
10
-
-
Piper nigrum
10
-
-
Quisqualis indica
10
-
-
StrychNos colubrina
10
-
-
Tetracera akara
10
-
-
PLANTS WITH CULTURAL ASSOCIATION
-
-
-
Alstonia scholaris
41
-
-
Dalbergia sisoo
46
-
-
Michelia chempaca
34
-
-
Neolamarckia Cadamba
36
-
-
Syszygium cumini
23
-
-
Saraca ashoca
21
-
-
Tamarindus indica
13
-
-
Artocarpus hirsutus
22
-
-
Artocarpus altilis
17
-
-
Anacardium occidentale
8
-
-
Artocarpus heterophyllus
6
-
-
Mangifera indica
4
-
-
Bambusa multiplex
62
-
-
Cassia fistula
44
-
-
Garcinia Indica
8
-
-
Phyllanthus emblica
8
-
-
Manilkara zapota
23
-
-
Phyllanthus acidus
23
-
-
Pithecellobium dulce
13
-
-
Ixora coccinia
70
-
-
Heliconia Mix
500
-
-
Allamanda nerifolia
120
-
-
Jasminum grandiflorum
175
-
-
Jasminum officinale
300
-
-
Mirabilis jalapa
400
-
-
Tabeamaemontana diverticata
150
-
-
Caesalpinia pulcherrima
30
-
-
Clerodentron paniculatum
1100
-
-
Malpighia coccigera
1500
-
-
Hibiscus rosasinensis
150
-
-
Nerium indicum
900
-
-
Biophytum sensitivum
240
-
-
wedelia
4450
-
-
MEDICINAL PLANTS EXPLORIUM
-
-
-
Punica granatum
21
-
-
Phyllanthus emblica
42
-
-
Withania somnifera
21
-
-
Moringa oleifera
42
-
-
Lawsonia inermis
21
-
-
Holarrhena pubescens
21
-
-
Bauhinia tomentosa
42
-
-
Centella asiatica
29
-
-
Bacopa monnieri
29
-
-
Adhatoda zeylanica
21
-
-
Aloe vera
13
-
-
Andrographis paniculata
21
-
-
Ruta graveolens
21
-
-
Sauropus androgynus
13
-
-
Stevia rebaudiana
29
-
-
Hibiscus rosa-sinensis
13
-
-
Murraya koenigii
13
-
-
ocimum tenuiflorum
29
-
-
Spilanthes calva
21
-
-
Coleus aromaticus
29
-
-
Cymbopogan citratus
21
-
-
Cynodon dactylon
29
-
-
Eclipta prostrata
29
-
-
Vetiveria zizanioides
13
-
-
Asparagus racemosus
13
-
-
Piper betle
8
-
-
Basella alba
8
-
-
Gymneme sylvestre
8
-
-
Piper longum
8
-
-
PART - 6 Electrical
-
-
-
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. Fire Retardant Low Smoke FRLS PVC insulated copper conductor single core cable etc as required. - Group C
1276
-
-
Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.
26
-
-
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
3705
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).
290
-
-
Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.
155
-
-
Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top along with 20 amps "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.
92
-
-
Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.
102
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. - 3 pin 5/6 amp socket outlet
169
-
-
Conveyance, installation , testing and commissioning of exhaust fans of size up to 450mm in the existing opening, fixing necessary anchor bolts / bolt and nuts etc., as required including giving connections with the supplied wire along with the exhaust fan.
24
-
-
Wiring for circuit / submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required for indipendent 5 Amps socket - 2x1.5 sq.mm + 1x1.5 sq.mm earth wire
1720
-
-
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required for lighting switch box run of mains. - 2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
2156
-
-
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required for LDB incoming - 4 X 6 sq. mm + 2 X 6 sq. mm earth wire
930
-
-
Wiring for circuit / submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required for PDB incoming - 4 X 10 sq. mm + 2 X 6 sq. mm earth wire
580
-
-
Wiring for circuit / submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required for VTPNDB incoming - 4 X 16 sq. mm + 2 X 6 sq. mm earth wire
160
-
-
Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. - 2 Pair
2170
-
-
Supplying and fixing Telephone socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
62
-
-
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.
1530
-
-
Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. - TV antenna socket outlet
29
-
-
Supplying and fixing of data socket outlet modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
72
-
-
Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. - 25 mm
5500
-
-
Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required. - 100 mm X 100 mm X 60 mm deep
50
-
-
Supplying and drawn of UTP 4 pair CAT 6 LAN cable in the existing surface/recessed steel/PVC conduit as required - 1 run of Cable
1800
-
-
Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/ RCCB/Isolator - 12 way, Double door
12
-
-
Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required - 8 way (8+24) - three phase double cover (IP 42/43)
36
-
-
Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required
8 way (8+18) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43) - 8 way Double door
4
-
-
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. - Single pole
972
-
-
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. - Single pole and netural
12
-
-
Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. - Triple pole
32
-
-
Supplying and fixing - 63 amps, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.
19
-
-
Supplying and fixing 40 amps, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.- 40 amps
21
-
-
Supplying and fixing 40 amps, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
22
-
-
Supplying and fixing 63 amps, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.
16
-
-
Earthing with G.I. earth pipe 4.5 RM long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required
24
-
-
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 RM long etc. with charcoal/ coke and salt as required.
12
-
-
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
760
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
1440
-
-
Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.
570
-
-
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
980
-
-
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube,having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.
12
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)
434
-
-
Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)
160
-
-
Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.
8
-
-
Laying copper/ G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.
120
-
-
Conveyance, installation, testing and commissioning of pre-wired fluorescent fitting of all types complete with all accessories and fluorescent lamps etc. directly on wall using 2 Nos. flat iron bracket made from 25x6mm flat iron, painting the flat iron bracket and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required.
20
-
-
Conveyance, installation, testing and commissioning of pre-wired light fitting of all types complete with all accessories and fluorescent lamps etc. suspended from ceiling using 2 Nos steel chain (16 SWG or nearest available size) of length not exceeding 30 cm properly hooked to steel hooks anchored to the ceiling and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required.
700
-
-
Conveyance installation testing and commissioning of pre-wired 600 x 600 mm square type fluorescent fitting complete with all accessories and fluorescent lamps etc. suspended from ceiling using 4 Nos steel chain (16 SWG or nearest) of length not exceeding 30 cm properly hooked to steel hooks anchored to the ceiling and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required. (for fitting in false ceiling)
159
-
-
Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.
20 mm
372
-
-
Supply, conveyance, installation, testing and commissioning of 1200 mm sweep -5star rated ceiling fan complete with 300mm down rod , canopies, shackles and blades and resistance type regulator working on 230V/240V single phase A/C using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.
86
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). for LDB - 3.5 core 25 sq. mm
155
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). for PDB - 3.5 core 35 sq. mm
155
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). for VTPNDB - 3.5 core 50 sq. mm
140
-
-
Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. for LDB - 3.5 core 25 sq. mm with factory made clamp
70
-
-
Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. for PDB - 3.5 core 35 sq. mm with factory made clamp
70
-
-
Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. VTPN LDB - 3.5 core 50 sq. mm with factory made clamp
60
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. - 3 1/2X25 sq.mm (28mm)
20
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3 1/2X 35 sq. mm (32mm)
18
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. - 3 1/2 X 50 sq. mm (35mm)
8
-
-
Supplying, testing and commissioning of Passive Infrared (PIR) technology based occupancy sensor with day light dimming (lighting level shall be regulated as per availability of natural day light in an area along with occupancy detection .) having high performance, regulating programmable type, suitable for connected load upto 10 Amp, for mounting height up to 2.8 mtr and for 5 m diameter coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.
12
-
-
Supplying, installation, testing and commissioning of Microwave technology based occupancy sensor having high performance, non regulating programmable type, suitable for connected load upto 10 Amp, for mounting height up to 2.6 mtr and for 5m x 20 m coverage area along with necessary fixing arrangements i/c programming at site etc. complete as required.
49
-
-
Supply, erection, testing and commissioning of 18 W LED down lighter fitting with cool day light made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.
455
-
-
Supply, erection, testing and commissioning of 24 W LED down lighter fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.
197
-
-
Supply, erection, testing and commissioning of 36 W LED down lighter fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.
180
-
-
Supply, erection, testing and commissioning of 18 W LED down lighter fittingmade out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including Sealed maintenance free rechargeable batteries with a battery autonomy of 30 minutes, inbuilt battery charger, fuse, test switch, electronic drivers, day light colour LED inter connecting wiring etc., including accessories all inclusive.
127
-
-
Supply, erection, testing and commissioning of 24 W LED down lighter fitting with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including Sealed maintenance free rechargeable batteries with a battery autonomy of 30 minutes, inbuilt battery charger, fuse, test switch, electronic drivers, day light colour LED inter connecting wiring etc., including accessories all inclusive.
58
-
-
Supply, erection, testing and commissioning of 36 W LED down lighter fitting with with self contained battery with a battery autonomy of 30 minutes with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including Sealed maintenance free rechargeable batteries with a battery autonomy of 30 minutes, inbuilt battery charger, fuse, test switch, electronic drivers, day light colour LED inter connecting wiring etc., including accessories all inclusive.
43
-
-
Supply, erection, testing and commissioning of 10 W LED bulk head fitting with cool day light suitable for surface mounting, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, Suitable for fitting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.
60
-
-
Supply, erection, testing and commissioning of 150 W LED outdoor flood light fitting with cool day light suitable for surface / recessed mounting, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, including electronic drivers, day light colour LED lamps, inter connecting wiring including suitable fabricated mounting arrangement compressing of 50 mm dia. class B, GI pipe with necessary mounting channels and angles, fasteners including necessary foundations etc., accessories all inclusive.
40
-
-
Supply, erection, testing and commissioning of 3 W LED foot light with cool day light suitable for surface mounting, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, Suitable for fitting including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.
8
-
-
Supply, erection, testing and commissioning of 11 W LED entry / exit light fitting with with self contained battery with a battery autonomy of 30 minutes with cool day light, made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for recessed / surface mounting including Sealed maintenance free rechargeable batteries with a battery autonomy of 30 minutes, inbuilt battery charger, fuse, test switch, electronic drivers, day light colour LED inter connecting wiring etc., including accessories all inclusive.
2
-
-
Supply and providing 300 mm (12") sweep (light duty) 1400 RPM, AC exhaust fan complete in the provided cutout including interconnection wire.
16
-
-
Supply and providing 450 mm (18") sweep (light duty) 1400 RPM, AC exhaust fan complete in the provided cutout including interconnection wire.
8
-
-
Supply, conveyance, installation, testing and commissioning of 600 mm dia wall mounting fans of the following sizes using standard accessories excluding resistance type regulator, wiring with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring, mounting clamp etc., all inclusive as required.
16
-
-
Supply, erection, testing and commissioning of track lighting suitable 230 V AC bus, GI mounting accessories etc.
160
-
-
Supply, erection, testing and commissioning of 18 W LED down lighter fitting suitable for track lighting with cool day light made out of CRCA powder coated body, aluminium reflectors, poly methyl meth acrylate (PMMA) diffuser, glare free light, suitable for track mounting type including electronic drivers, day light colour LED lamps, inter connecting wiring including accessories all inclusive.
163
-
-
Supply, installation testing and commissioning of Online 7.5 KVA UPS with 30 minitues SMF battery backup, with 415V, 3 phase input, 230 V single phase output
3
-
-
Installation of Data Acquisition compatible Extensible type Ring Main Unit with VCB -CTC (E) (Cable -Transformer -Cable )Design, Engineering, Manufacture, Assembly, Inspection and Testing before supply, Packing and delivery at site, erection, installation, testing & commissioning of the following HT switchgear with all accessories and suitable for installation in three phase, three wire,11 kV, 50 Hz, A.C. distribution network. complete with all accessories erected in the provided foundation complete as per specification and as directed by engineer in charge at site. The RMU shall be complying to KSBE specification.Outdoor type, 11 kV Extensible Ring Main unit (RMU), with combination of 2 Nos. Load Break Isolators (for Loop IN and Loop OUT) & 1 No. Vacuum Circuit Breaker in tee OFF Each LBS panel shall consist of the following1 No. 11kV, 630A, 26.3 kA for 3 sec, Manually Operated load break switch1 No. Mechanical position Indicator (ON/OFF)Each Vacuum Circuit Breaker (VCB) feeder shall Comprise of following1 No. 11 kV, 630A, 26.3 kA, for 3 sec, manual operated VCB1 No. Self Powered 3O/C+1E/F RelayCommon Items & Accessories for each RMU1 set Operating Handle (Supplied Loose with RMU)The panel shall be suitable for terminating 1 R of 3C x 300 Sq.mm XLPE 11 kV (E) cable
1
-
-
Supply, testing and commissioning, of 11 kV (E) grade, 3 core 300 Sq Mm XLPE Al. Ar. cable confirming to IS 7098 laid on excavated trench / poles including the cost of clamping, cable tags, clamps, complete in a manner as per specification and as directed by engineer-in charge at site.
350
-
-
Laying of Nos PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.
Above 120 sq. mm and upto 400 sq. mm
350
-
-
Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core x 300 sq. mm, XLPE aluminium conductor cable of 11 KV grade as required
1
-
-
Supplying and making indoor cable end jointing with cast resin compound, including, lugs and other jointing materials, for following size of 3 core x 300 sq. mm XLPE aluminium conductor cable of 11 KV grade as required:
3
-
-
Supply and fixing cable route marker of cast iron with inscription there on, bolted / welded to 35 mm x 35 mm x 6 mm angle iron, 60 cm long and fixing the same in ground as required including necessary civil works.
7
-
-
Supply, erection, testing and commissioning of unitized substation with 750KVA transformer suitable for outdoor type including civil foundation as required with following:HT Incoming11kV 630 Amps VCB 1 No. with aluminium 630 Amps busbars with 26.3.0 kA, 3 sec. fault current carrying capacity.Single VCB panel Type - Cable I/C and cable O/G [CICO] outdoor Kiosk typeVCB panel shall comprise of the following 1 No. of 11 kV, 630A, 26.3 kA for 3 sec, TP, EDO type, Vacuum circuit breaker with trip free mechanismSelf powered O/C & E/F relay type CSPR with Single core cast resin type CT (Protection Core – 2.5VA & CL-5P10)Control & ProtectionSurge Arrester (10 kV,10KA)Earth switchDigital panel meter with RS 485 communication featureLocal / remote operation using SCADA systemNoteThe panel shall be suitable for terminating 1 R of 3C x 300.0 Sq.mm XLPE 11 kV (E) cable750kVA, 11KV /433V, DYn11, Cast Resin Dry Type Distribution transformer having a no load voltage ratio of 11KV/433V with top HT & LT Bushings. Tapping +5% to -5% in steps of 2.5% shall be provided at line end of HV winding. Changing of taps shall be carried out by means Offload tap changing. Class of insulation "F" with High efficiency transformerLT Incoming1250 Amps 50 kA, TPN, ACB -1 NoLT Outgoing1250 A, 50 kA TPN, ACB - 1 No. with busduct out going 400 A 50 kA TPN, MCCB - 2 Nos250 A 50 kA TPN, MCCB - 2 Nos125 A 50 kA TPN, MCCB - 1 NosThe panel incomers shall be suitable for local / remote operation using SCADA control.
1
-
-
Supplying, installing by suspension on ceiling, testing and commissioning of 1250 amps 50 KA SC for 1 sec, capacity Sandwich Type Bus Trunking for use on 3 phase 4 wire 415 volts, 50 Hz A.C. supply with metal clad enclosure made of 1.6mm thick steel sheet duly powder coated in convenient section complete with 4 Nos aluminium bus bars, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every RM, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size( one on each side) including G.I clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required.
20
-
-
Supply, Installation, Testing and Commissioning of MV panel CPRI / ERDI certified make of panel, cubicle type, single front, free standing, floor mounted, 14 SWG CRCA sheet steel, enclosed separate compartment for each feeder, front operated, powder coated, indoor type, dust and vermin proof, hinged lockable doors, IP 42, with base frame, incomer with digital multi functional meter, volt meter and ammeter provided with RS 485 communication port along with selector switch, auto / manual selector switch, close / trip switch, ELR relay with CT, cluster LED type indicators, in the incoming feeders, complete with electrolytic grade aluminium bus bars, Internal wiring, colour coding, ferrules, cable gland plates, Aluminium earth bus for the entire length of the panel with bonding to earth, panel mounting M.S channels, fasteners, etc., for the following panels:1250A, 50 kA, 415 Volts, TPN 50 Hz, Aluminium bus bars with 2 runs x 100 x 8 mm thick for phase and 1 run x 100 x 10 mm thick for neutral with colour coaded heat shrink sleeve, The ACB is of draw out type with electrically spring charge motor mechanism, fault protection and trip settings, remote trip facility where as the MCCB is of thermal magnitic / electricronic microprossessor based trip relay - with short circuit and overload protection with remote trip facility. The panel details as follows:-Transformer and DG incomer1 No. each of 1250A, FP EDO, ACB, 50 kA - for Transformer with Microprocessor based O/C, S/C & E/F releases with electrical and mechanical interlock with DG incomer - 1 No. each of 1250A, FP EDO, ACB, 50 kA - for DG set with Microprocessor based O/C, S/C & E/F releases with electrical and mechanical interlock with DG incomer CT based Earth fault relay with necessary CBCT & under voltage protection for incomingsOutgoing630 A, TPN MCCB 50 kA, electricronic microprossessor based 3 Nos.400 A, TPN MCCB 50 kA, electricronic microprossessor based - 2 Nos.250 A, TPN MCCB 50 kA, thermal magnitic based - 7 No125 A, TPN MCCB 36 kA, thermal magnitic based - 2 NosAMF relay with necessary Sensing and interconnecting wirings as required. Digital MFM relay with necessary selector switchSub panel
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication feature for transformer and DG incomersIndications, protections and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP, - Main Lighting Distribution Panel - Bus bar400A, 36 kA, 415 Volts, TPN (100 % neutral) , 50 Hz Aluminium bus bars with colour coaded heat shrink sleeve, Incomer1 No. 400A, TPN MCCB, 36 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing125 A, TPN MCCB 25 kA, - 8 Nos63 A, TPN MCCB 25 kA, - 2 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication feature for transformer and DG incomersIndications, protections and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP,- HVAC panel - Busbar 630A, 50 kA, 415 Volts, TPN, 50 Hz Aluminium bus bars with colour coaded heat shrink sleeve, Incomer1 No. each of 630A, TPN, MCCB, 50 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing400 A, TPN MCCB 50 kA, Microprocessor based - 2 Nos250 A, TPN MCCB 50 kA, Microprocessor based - 1 Nos160 A, TPN MCCB 36 kA, thermal magnitic based - 1 Nos100 A, TPN MCCB 25 kA, thermal magnitic based - 4 Nos63 A TPN MCCB 25 kA thermal magnitic based , - 3 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication feature for transformer and DG incomersIndications, protections and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP, - Auditorium building lighting panel -1 - Busbar 125A, 25 kA, 415 Volts, TPN (100 % neutral) , 50 Hz Aluminium bus bars Incomer1 No. 125A, TPN, MCCB, 25 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing100 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP, Auditorium building Power panel - 1 - Busbar 250A, 36 kA, 415 Volts, TPN, 50 Hz Aluminium bus bars Incomer1 No. 250A, TPN, MCCB, 36 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing125 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A TPN MCCB 25 kA thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication feature for transformer and DG incomersIndications, protections and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP, - Auditorium building lighting panel -2 - Busbar 125A, 25 kA, 415 Volts, TPN (100 % neutral) , 50 Hz Aluminium bus bars Incomer1 No. 125A, TPN, MCCB, 25 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing100 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP, Auditorium building Power panel - 2 - Busbar 250A, 36 kA, 415 Volts, TPN, 50 Hz Aluminium bus bars Incomer1 No. 250A, TPN, MCCB, 36 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing125 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A TPN MCCB 25 kA thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.Exhibition building Lighting panel - 1 - Busbar 125A, 25 kA, 415 Volts, TPN (100 % neutral) , 50 Hz Aluminium bus bars Incomer1 No. 125A, TPN, MCCB, 25 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing100 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components, and form-IIIB form of construction.Cluster type LED indication lamps for 3 phases, ON, OFF, TRIP. Exhibition building Power panel - 1 - Busbar 250A, 36 kA, 415 Volts, TPN, 50 Hz Aluminium bus bars Incomer1 No. 250A, TPN, MCCB, 36 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing125 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A TPN MCCB 25 kA thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components and form-IIIB form of construction.Exhibition building Lighting panel - 2 - Busbar 125A, 25 kA, 415 Volts, TPN (100 % neutral) , 50 Hz Aluminium bus bars Incomer1 No. 125A, TPN, MCCB, 25 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing100 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components, and form-IIIB form of construction.MeteringDigital multi-function meter with necessary CTs (A, V, kW kWh, kVA, RkVA, PF), with RS 485 communication feature for transformer and DG incomersIndications, protections and special featuresCluster type LED indication lamps for 3 phases, ON, OFF, TRIP.Exhibition building Power panel - 2 Busbar 250A, 36 kA, 415 Volts, TPN, 50 Hz Aluminium bus bars Incomer1 No. 250A, TPN, MCCB, 36 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing125 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A TPN MCCB 25 kA thermal magnitic based - 6 Nos
1
-
-
Design, supply, assembly, wiring, supply, installation, testing and commissioning of CPRI/ERDA tested floor standing, single front, fully compartmentalized, double ended, IEC 60439 compliant, 14 G CRCA sheet steel fabricated IP 42 protected complete as per specification, comprising of the following major switchgear/ devices / components, and form-IIIB form of construction.Cluster type LED indication lamps for 3 phases, ON, OFF, TRIP.Utility panel - Busbar 250A, 36 kA, 415 Volts, TPN, 50 Hz Aluminium bus bars Incomer1 No. 250A, TPN, MCCB, 36 kA with Microprocessor based O/C, S/C & E/F releases.Outgoing125 A, TPN MCCB 25 kA, thermal magnitic based - 6 Nos63 A TPN MCCB 25 kA thermal magnitic based - 6 Nos
1
-
-
Supply, installation, testing and commissioning of 300 KVAr Automatic power factor correction panel (APFC) with 12 steps of capacitor switching with 7 % de-tuned filter, cubicle type, free standing, powder coated, 14 G CRCA sheet steel enclosed separate compartment for each capacitor, front operated, indoor type dust & vermin proof, hinged, lockable doors, electrolytic grade aluminium bus bars with SMC /DMC insulator supports, Digital volt meter, Ammeter with selector switch, 8 stage Digital Automatic power factor correction controller, Auto / Manual selector switch, cluster LED type indicators, in the incomer, complete with 480 Volts MPP type Power capacitors, with 1 No. 100 KVAr, 2 Nos. 50 KVAr, 3 Nos. 25 KVAr, 2 no. 10 KVAr and 1 no. 5 KVAR capacitor banks in delta connection, capacitor duty contactors, MCCB’s, timer, start, stop, push buttons, internal wiring, colour coding, ferrules, cable gland plates, Aluminium earth bus for the entire length of the panel with bonding to earth & painting, Panel mounting MS Channels, fasteners, etc., including all associated control wiring and interlocking circuitry, MV panel sensing CT interconnecting wiring etc., all inclusive.
1
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). -
3 x 2.5 Sq.mm. YFY, XLPE, Cu, UG cable
500
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). -
12 x 2.5 Sq.mm. YFY, XLPE, Cu, UG cable
200
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). - 4 x 10 Sq.mm. AYFY, XLPE, Al, UG cable
275
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). - 4 x 16 Sq.mm. AYFY, XLPE, Al, UG cable
200
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). -
3½ x 70 Sq.mm. AYFY, XLPE, Al, UG cable
1169
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). -
3½ x 120 Sq.mm. AYFY, XLPE, Al, UG cable
766
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). -
3½ x 185 Sq.mm. AYFY, XLPE, Al, UG cable
529
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). - 3½ x 240 Sq.mm. AYFY, XLPE, Al, UG cable
124
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). - 3½ x 300 Sq.mm. AYFY, XLPE, Al, UG cable
120
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required for 3.5 core 70 sq mm
501
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required for 3.5 core 120 sq mm
329
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required for 3.5 core 185 sq mm
226
-
-
Supply & laying of Nos PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required for 3.5 core 240 sq mm
56
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3 X 2.50 sq. mm Cu, conductor
20
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
12 X 2.50 sq. mm Cu, conductor
10
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
4 X 10 sq. mm (25mm)
20
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
4 x 16 Sq.mm. AYFY, XLPE, Al, UG cable
16
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ x 70 Sq.mm. AYFY, XLPE, Al, UG cable
22
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ x 120 Sq.mm. AYFY, XLPE, Al, UG cable
4
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ x 185 Sq.mm. AYFY, XLPE, Al, UG cable
4
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ x 240 Sq.mm. AYFY, XLPE, Al, UG cable
8
-
-
Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
3½ x 300 Sq.mm. AYFY, XLPE, Al, UG cable
8
-
-
Supplying and installing following size of perforated pre-painted M.S. cable trays cross members with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.
600 mm width X 62.5 mm depth X 2.0 mm thickness
200
-
-
Supplying and installing following size of perforated pre-painted M.S. cable trays cross members with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as requir
450 mm wide x 100 mm height x 2 mm Thickness Ladder cable tray with cover
400
-
-
Supplying and installing following size of perforated pre-painted M.S. cable trays cross members with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as requir
300 mm wide x 50 mm height x 1.6 mm Thickness perforated cable tray with cover
550
-
-
Supply and Provision of Fire Sealant of HILTI (or) equivalent make at cable penetration Area
10
-
-
Supplying and making cable route marker with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) of size 60 cm X 60 cm at the bottom and 50 cm X 50 cm at the top with a thickness of 10cm including inscription duly engraved as required.
183
-
-
Supply, erection, testing, commissioning of 630 KVA, 415 V, 3 phase, 50 Hz, DG Set with diesel engine at 1500 RPM coupled with alternator rated at 630 KVA, 415 V, 0.8 PF mounted on a channel Iron base frame, fuel tank of adequate capacity, starting batteries with leads, AMF panel, hospital type silencer, with acoustic enclosure, control panel, inter connecting control cable, cable end termination, including lubrication system, cooling system, all inclusive. DG set should comply with central pollution control board (CPCB) norms as per the latest environment (protection) rules,
1
-
-
Earthing with G.I. earth pipe 4.5 RM long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required
24
-
-
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 RM long etc. with charcoal/ coke and salt as required.
6
-
-
Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.
150
-
-
Supplying and laying 25 mm X 5 mm G.I strip at 0.50 RM below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required.(Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)
450
-
-
Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.
500
-
-
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.
400
-
-
Supplying and laying 25 mm X 5 mm copper strip at 0.50 RM below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt & spring washer spaced at 50mm)
150
-
-
Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing including necessary GI hooks etc., as required.
300
-
-
Supplying and laying 50 mm X 6 mm copper strip at 0.50 RM below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with brazing and with bittumin paint - 50 mm X 6 mm copper strip (2.67 kg/mtr)
60
-
-
Supplying and laying 50 mm X 6 mm Hot dipped GI .strip at 0.50 RM below ground as strip earth electrode, including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with welding / G.I bolt, nut, washer etc., with bittumin paint - 50 mm X 6 mm Hot dipped G.I strip (2.4 kg/mtr)
250
-
-
Supply of suitable for 11 kV Rubber Hand Gloves
2
-
-
Supply and fixing of 11 kV Caution Board
2
-
-
Supply and fixing of 415V Caution Board
26
-
-
Supply and fixing of Shock Treatment chart as per IE Rules (local language must)
2
-
-
Supply, erecting and connecting 4 No. 10 Ltr. capacity Fire Bucket painted with Red oxide outside and White inside with handle at the bottom in a floor mounted angle iron frame with necessary clamps, screws etc. The angle iron frame shall also be painted with Red paint.
4
-
-
Supply, erecting & connecting a 5 kg fire extinguisher properly fixed on the wall with necessary clamps, screws, bolts and nuts etc. The extinguisher shall be suitable for all types of fires (A, B, & C)
4
-
-
Supply and fixing of First Aid Box.
2
-
-
11 kV grade synthetic insulation mat, 1000 mm x 2.50 mm thickness, compliant to IS 15652 with latest amendment, Class A, CPRI type test certificate required
54
-
-
Preparation of drawings and coordination with CEIG / CEA / KSEB for the drawing approval including all necessary assistance to obtain approval,
1
-
-
Design, manufacture, supply, erection, testing and commissioning of 415 V street lighting feeder pillar box suitable for outdoor installation, made up of CRCA sheet steel of thickness not less than 2 mm with a weather proof canopy of top, double door construction, IP 55 protection, anti corrosive chemical resistant paint with 1no. 125 A TPN MCCB with 16 kA breaking capacity in the incoming and 8 Nos 25 A, TPN contactor 10 Nos. 25 A TPN MCCB, 24 Nos, 10A SP MCB as outgoing, automatic dawn and dusk with cyclic timer control for street light outgoing and adequate plate to terminate suitable cable as incomer and suitable cable as outgoing. energy saver for automatic switching ON/OFF as per pre-sets time cycle, digital multifunctional meter with RS485 port and suitable CT etc., including concrete pedestal and associated civil works.
2
-
-
Design, manufacture, supply, erection, testing and commissioning of LED street light pole, Post top Light Pyramid - 6064 - 30 W or equivalent with FRP junction box, 3 R x 2.50 sq.mm FRLS insulated copper conductor with end termination for individual fitting , 6 Amps, SP MCB - 1 no. connecting coil earthing using 8 SWG GI wire etc., with embedded type foundation, civil works etc., all inclusive.
91
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive. Foot Light - Sudo Mini - Beam -2759 - 3 W or equivalent
48
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive.Wall Light - Jado - 2753 - 12 Wor equivalent
40
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive.tree Light - Triospace Bracket 7057 7W LED or equivalent
18
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive.medium bollard Light - Ritu bollard 6952 9W or equivalent with all necessary civil works as required.
57
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive.Supply and fixing of Wall cylin mini 7897 6W LED to detail or equivalent with all necessary civil works as required as directed by Engineer-In-Charge.
19
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive of Under Water light - Klite -4105 to detail or equivalent with all necessary civil works as required as directed by Engineer-In-Charge.
2
-
-
Design, manufacture, supply, erection, testing and commissioning of LED all inclusive of Light art pire to detail or equivalent with all necessary civil works as required as directed by Engineer-In-Charge.
13
-
-
Wiring for light po- int/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. Fire Retardant Low Smoke FRLS PVC insulated copper conductor single core cable etc as required.Group C
39
-
-
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required
2x1.5 sq.mm + 1x1.5 sq.mm earth wire
950
-
-
Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / r ecessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire
280
-
-
Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.
100
-
-
Supply, conveyance, installation, testing and commissioning of ceiling fans of 1200mm sweep -5star rated ceiling fan complete with 300mm down rod , canopies, shackles and blades and resistance type regulator working on 230V/240V single phase A/C using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.
6
-
-
Supply, Laying, testing and commissioning of the following 1100 V grade XLPE insulated, aluminium / copper conductor, armoured, UG cables. Laying of the above supplied XLPE insulated aluminium / copper cable direct in ground including excavation, sand cushioning, protective covering and refilling trench etc as required.
4 x 10 Sq.mm. AYFY, XLPE, Al, UG cable
1872
-
-
Supply, Laying, testing and commissioning of the following 1100 V grade XLPE insulated, aluminium / copper conductor, armoured, UG cables. Laying of the above supplied XLPE insulated aluminium / copper cable direct in ground including excavation, sand cushioning, protective covering and refilling trench etc as required.
4 x 16 Sq.mm. AYFY, XLPE, Al, UG cable
1282
-
-
Supply and making end termination with brass single compression gland and aluminium lugs for following size of XLPE insulated aluminium / copper conductor cable of 1.1kV grade as required.
4 x 10 Sq.mm. AYFY, XLPE, Al, UG cable
224
-
-
Supply and making end termination with brass single compression gland and aluminium lugs for following size of XLPE insulated aluminium / copper conductor cable of 1.1kV grade as required.
4 x 16 Sq.mm. AYFY, XLPE, Al, UG cable
150
-
-
Part - 7 HVAC works
-
-
-
AUDITORIUM & STAGE: (R 407 / R410 / Eqvt Eco Friendly Refgt can be quoted for Units mentioning Gas Type individually by OEM)
Supply, Installation, Leading, Positioning, Testing and commissioning of 33 / 36 TR Capacity (To Suit) of 14000CFM, 55 mm static pressure, Floor mounted Double Skin, (48 - 50mm thick PUF panels, density of 40kg/cum, with min 0.6-mm thick inner & 0.8-mm outer skin) air-handling units, with Thermal break profile, Pre-filter section with Pre-filters (90% down to 10 micron) with highest Efficiency along filter frame. The AHU shall be with 6 row DX Cooling coil section to suit the ODU Selected along with the AHU for Palakkad climate. The AHU shall have a drain pan with min 1.2-mm thick Stainless steel (SS 304) material. Pan should be Insulated with min 9-mm thick Nitrile rubber at the bottom. Copper tubes selected shall be of 3/8 inch dia with 0.5mm thick and min of 12 Fins Per inch shall be maintained. The Vendor should consider suitable expansion Valve, Filter Drier (AHU KIT if any) so that the AHU is coupled with the selected ODU. AHU shall also have a DIDW fan Forward curve blower with fan motor of IE 3 Motor (IE2 Can be used only of IE3 is not available for that capacity), and the fan will be connected with drive coupling / belt driven to suit, along with necessary mounting frame, Vibration isolators, 2 MM GI base frame, Aluminium structural frame work, Fire retardant flexible connection, Marine light, Access door and Access door limit switch, View port for fan section, accessories and as per technical specifications. Coils shall be sized to meet conditions provided in AHU specifications. The Coil face velocity shall not exceed 2.5 M/s. The quoted price shall include the cost of supply, installation, testing and commissioning of air handling unit wall mountable electrical starter panel , main circuit breaker, LCD screen with temperature indicator. Panel shall be preferably wall mounted type, powder coated type. The electrical panel shall have potential free relay contacts to be interlocked with fire alarm control module & BMS on/off command, trip status.
2
-
-
AUDITORIUM & STAGE: (R 407 / R410 / Eqvt Eco Friendly Refgt can be quoted for Units mentioning Gas Type individually by OEM)
SITC of 11 TR / 12 TR Condensing unit (Inverter Type can also be quoted by Vendor) comprising ODU with Scroll compressor and condenser fan unit to suit the above indicated AHU. The vendor shall consider all the interconnecting circuit components required for connecting the AHU including safety & communication between the AHU & ODU.
6
-
-
AUDITORIUM & STAGE: (R 407 / R410 / Eqvt Eco Friendly Refgt can be quoted for Units mentioning Gas Type individually by OEM)
Communication Cable between AHU and Outdoor unit to suit
150
-
-
AUDITORIUM & STAGE: (R 407 / R410 / Eqvt Eco Friendly Refgt can be quoted for Units mentioning Gas Type individually by OEM)
Panel for AHU
2
-
-
AUDITORIUM & STAGE: (R 407 / R410 / Eqvt Eco Friendly Refgt can be quoted for Units mentioning Gas Type individually by OEM)
Power cable between AHU and Condensing unit (4C X 10 sq.mm)
120
-
-
AV THEATRE
Design, Supply, Installation, Leading, Positioning, Testing and commissioning of 17 /18 TR Capacity (To Suit) 6800CFM, 40 mm static pressure, Ceiling Suspended (25mm thick PUF panels, density of 40kg/cum, with min 0.6-mm thick inner & 0.8-mm outer skin) air-handling units, having 50mm base channel frame, Pre-filter section with Pre-filters (90% down to 10 micron) with highest Efficiency along filter frame, The CSU Shall have 6 row DX Cooling coil section to suit the ODU Selected along with the CSU for Palakkad climate. The CSU shall have a drain pan with min 1.2-mm thick Stainless steel (SS 304) material. Pan should be Insulated with min 13-mm thick Nitrile rubber at the bottom. Fan outlet velocity shall not exceed 8- 10 M/S. The CSU shall have copper tubes of min 0.5 mm thick with atleast 12 fins per inch. The Vendor should consider suitable expansion Valve, Filter Drier (CSU KIT if any) so that the CSU is coupled with the selected ODU. AHU shall also have a DIDW forward curve fan blower with fan motor of minimum IE 3 Motor (IE2 will be accepted only if IE3 of suitable capacity is not available), fan with belt drive or to suit, along with necessary mounting frame, support structure from ceiling, Vibration isolators, Aluminium structural frame work, Fire retardant flexible connection, Access door and Access door limit switch, Coils shall be sized to meet conditions provided in CSU specifications.The Coil face velocity shall not exceed 8 - 10 M/s. The quoted price shall include the cost of supply, installation, testing and commissioning of air handling unit wall mountable electrical starter panel , main circuit breaker, LCD screen with temperature indicator. Panel shall be preferably wall mounted type, powder coated type. The electrical panel shall have potential free relay contacts to be interlocked with fire alarm control module & BMS on/off command, trip status.
2
-
-
AV THEATRE
SITC , Unloading, leading, positioning 8.5/9 TR Air Cooled Condensing unit with SCROLL compressor (inverter Type can also be quoted by vendor), an outdoor unit having suitable condenser fan as per OEM recommendation. The interconnection between the CSU and the ODU will be in the bidders scope
4
-
-
AV THEATRE
Communication Cable between AHU and Outdoor unit to suit
75
-
-
AV THEATRE
Panel for CSU
2
-
-
AV THEATRE
Power cable between AHU and Condensing unit (4C X 10 sq.mm)
70
-
-
BLACK BOX
SITC , Unloading, leading, positioning 11 TR Ductable Split Unit circuit with air cooled outdoor unit SCROLL compressor, along with an outdoor unit having suitable condenser fan / or as per OEM recommendation. The Unit shall have all interconnecting communication cables so as to have effective communication between IDU & with ODU.
2
-
-
BLACK BOX
Communication Cable between AHU and Outdoor unit to suit
40
-
-
MIXING LAB & SEMINAR HALL
SITC , Unloading, leading, positioning 3 TR Cassette type Air Conditioner ( 2 Nos for Mixing lab and 4 Nos for Seminar hall)
6
-
-
MIXING LAB & SEMINAR HALL
SITC,Unloading, leading, positioning 8 HP Min Capacity (Mixing Lab)Variable Refrigerant Flow Outdoor unitwith compressor (Variable speed, Scroll), Air cooled condenser, fan motor, vibration isolation pads etc to be considered.
1
-
-
MIXING LAB & SEMINAR HALL
SITC,Unloading, leading, positioning 16 HP Min Capacity (Seminar Hall) Variable Refrigerant Flow Outdoor unitwith compressor (Variable speed, Scroll), Air cooled condenser, fan motor, vibration isolation pads etc to be considered.
1
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Mixing Lab (2 Indoor with One Out Door Unit for VRF Unit)
Suction Line - 5/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Mixing Lab (2 Indoor with One Out Door Unit for VRF Unit)
Liquid Line - 3/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Mixing Lab (2 Indoor with One Out Door Unit for VRF Unit)
Suction Line - 3/4"
10
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Mixing Lab (2 Indoor with One Out Door Unit for VRF Unit)
Liquid Line - 3/8"
10
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Black Box (Circuits shown separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Black Box (Circuits shown separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Black Box (Circuits shown separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Black Box (Circuits shown separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Auditorium (33 / 36 TR) - (6 Circuits shown Separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Suction Line - 1 1/8"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. AV theatre (2 Circuits shown separately)
Liquid Line - 1/2"
15
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units.
Seminar hall (4 IDU S connected with 16 HP ODU VRF)
Suction Line - 5/8"
20
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Seminar hall (4 IDU S connected with 16 HP ODU VRF)
Liquid Line - 3/8"
20
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Seminar hall (4 IDU S connected with 16 HP ODU VRF)
Suction Line - 3/4"
5
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Seminar hall (4 IDU S connected with 16 HP ODU VRF)
Liquid Line - 3/8"
5
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Seminar hall (4 IDU S connected with 16 HP ODU VRF)
Suction Line - 5/8"
10
-
-
SITC of Inter connected copper refrigerant piping with necessary supporting arrangements of min 19G Thk or to suit as per OEM Standards, EPDM tube insulation, fittings as required, pressure testing along with the indoor / out door. The pipings shall be coated with minimum of one coat of primer and two coats of enamel Painting. In case if the piping requires insulation the same shall be done for the liquid line and suction line along with all fittings, valves, and strainer bodies etc with 19mm / 13mm thick elastomeric nitrile rubber respectively. Drain pipes carrying Condensate water shall be insulated with min 6mm thick elastomeric Nitrile rubber. For proper drainage of condensate and to avoid any fouling smell, U trap shall be provided in drain piping wherever required. All piping support shall be pre fabricated type and pre painted sLotted angle support which has to be properly insulated with clamps etc.To protect the nitrile rubber insulation of exposed copper piping from degrading due to UV rays and atmospheric condition, the insulation shall be covered with Polyshield coating with at least two coats of resin and hardener (preferably with Polybond make or equivalent) over and above the nitrile rubber insulation. Fiber glass tape shall be helically wound and coated with painted 2 coats of resin and hardener to give smooth and paint finish. The refrigerant piping shall be hard drawn heavy duty copper of various sizes as per OEM recommendation with necessary supports, as required with all fittings between condensing unit & indoor units. Seminar hall (4 IDU S connected with 16 HP ODU VRF)
Liquid Line - 1 1/8"
10
-
-
Refrigerant Gas (Presumed unit comes with out gas and for additional qty required, If comes with Gas then this item is not required to be quoted)
180
-
-
SITC of condensate drain piping out of UPVC pipe with necessary insulation, fittings, U trap as required of size from the indoor unit up to the nearest drain point (Overall Measurement is indicated)
150
-
-
SITC of Rectangle duct with necessary supporting arrangements, and following SMACNA standards of sizing and supporting arrangements
24G G.I Sheet
250
-
-
SITC of Rectangle duct with necessary supporting arrangements, and following SMACNA standards of sizing and supporting arrangements
22G G.I Sheet
425
-
-
SITC of Rectangle duct with necessary supporting arrangements, and following SMACNA standards of sizing and supporting arrangements
20G G.I Sheet
5
-
-
SITC of Rectangle duct with necessary supporting arrangements, and following SMACNA standards of sizing and supporting arrangements
18G G.I Sheet
35
-
-
Supply and erection of GI Spiral Ducting with nesscessary fittings, joints, flanges, accessories and supports etc.. (Preferably with a universal support). Ducting shall be powder coated suitably wrt the room as per architects advice and the coating cost shall be included in the duct price below:
550 Dia
6
-
-
Supply and erection of GI Spiral Ducting with nesscessary fittings, joints, flanges, accessories and supports etc.. (Preferably with a universal support). Ducting shall be powder coated suitably wrt the room as per architects advice and the coating cost shall be included in the duct price below:
500 Dia
3
-
-
Supply and erection of GI Spiral Ducting with nesscessary fittings, joints, flanges, accessories and supports etc.. (Preferably with a universal support). Ducting shall be powder coated suitably wrt the room as per architects advice and the coating cost shall be included in the duct price below:
450 Dia
3
-
-
Supply and erection of GI Spiral Ducting with nesscessary fittings, joints, flanges, accessories and supports etc.. (Preferably with a universal support). Ducting shall be powder coated suitably wrt the room as per architects advice and the coating cost shall be included in the duct price below:
350 Dia
8
-
-
Supply and erection of GI Spiral Ducting with nesscessary fittings, joints, flanges, accessories and supports etc.. (Preferably with a universal support). Ducting shall be powder coated suitably wrt the room as per architects advice and the coating cost shall be included in the duct price below:
300 Dia
24
-
-
Supply and erection of GI Spiral Ducting with nesscessary fittings, joints, flanges, accessories and supports etc.. (Preferably with a universal support). Ducting shall be powder coated suitably wrt the room as per architects advice and the coating cost shall be included in the duct price below:
250 Dia
3
-
-
Supply of Canvas (Fire retardent) along with Damper for supply air for all the units Size - To suit
6
-
-
VCD for controlling air flow on Main ducts
6
-
-
Fresh air damper with pre filter to suit
2
-
-
Fire Damper with Fusible link to suit the return air
12
-
-
SITC of horizontal continuous grill/diffusers with the following sizes
BLACK BOX (11 TR) 2 Nos
Supply Air Grill with Damper
2
-
-
SITC of horizontal continuous grill/diffusers with the following sizes
BLACK BOX (11 TR) 2 Nos
RA Grill
3.8
-
-
SITC of horizontal continuous grill/diffusers with the following sizes
AUDITORIUM (33 TR - 2 Nos)
Supply Air Grill with Damper
6.5
-
-
SITC of horizontal continuous grill/diffusers with the following sizes
AUDITORIUM (33 TR - 2 Nos)
RA Grill
14
-
-
SITC of horizontal continuous grill/diffusers with the following sizes
AV THEATRE (22 TR)- 2 Nos
Supply Air Grill with Damper
5
-
-
SITC of horizontal continuous grill/diffusers with the following sizes
AV THEATRE (22 TR)- 2 NO
RA Grill
7
-
-
Supply & fixing of thermal insulation with min 9 mm thick closed cell nitrile rubber with a wrap over the ducting.
180
-
-
Supply & fixing of acoustic insulation with 10 mm thick open cell nitrile rubber
95
-
-
Rubber pads for out door units
1
-
-
MS Structural support / Channels for IDU s / ODU S 13Nos to suit including one coat of primer and two coats of enamel / rust proof /epoxy paint. The out door and indoor units should be mounted to have a easy reach for which if reqd hand rails / ladders etc to be provided
1750
-
-
Miscellenoeous like transportation / supervison etc
1
-
-
Part - 8 Acoustic & AV works
-
-
-
Auditorium- Supply, Installation & Providing of , Auditorium main false ceiling using square edge, acoustical glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 grid system.The T15 Grid system of 600x600mm module shall include wall angle (WA15W30) with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 (MT15W36) having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 (CT15W12) having flange width 15mm, height 32mm and length 1200mm is then interlocked into the pre-cut sLots in the Main T15 at 600mm centers in the direction perpendicular to the Main T15. Finally Cross T15 (CT15W06) having flange width 15mm, height 32mm and length 600mm are then interlocked into the pre cut sLots in the 1200mm Cross T15 at 1200mm centers and in direction parallel to the Main T15. Square edge of size 595x595x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind Acoustical panels are orianted in one direction to achieve uniform shade. Contractor to provide trapdoors as per size and finishes requested by other servicesbased on site condition.Appoved Recommended Makes- Anutone/Amstrong/Ecophone/Equivalent
445
-
-
Auditorium- Supply, Installation & Providing of Peripheral False ceilings with Tufbloc HDFR, square edge, magnesia cement core panels of size 1200x2400x10mm, density 1000Kgs/m3, weight 10 kg/m2, installed by using Strut ceiling framework.The Strut ceiling framework system shall include Strut WC25 Wall channel, fully knurled, sectional thickness 0.55mm, length 3600mm, unequal flanges of 20 & 30mm and web of 25mm, fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then suspend Strut MC45 Main channels, fully knurled, sectional thickness 0.8mm, length 3600mm, equal flanges of 15mm and web 45mm from the soffit at 1200mm centers with Strut SA25, fully knurled, Suspender angle with sectional thickness 0.55mm, unequal flanges of 25 & 10mm. Strut CC25 Cross channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 35mm, depth of 20mm and equal flanges 9.5mm is fastened to the Strut MC45 perpendicularly at 600mm centers. Tufbloc HDFR, 1200x2400x10mm is installed on the Strut CC25 with suitable fasteners in a staggered manner. 4mm gap should be maintained between adjacent Tufblocboards on all sides.Appoved Recommended Makes- Anutone/Gyproc/Amstrong/Equivalent
175
-
-
Auditorium- Supply, Installation & Providing of Stage False Ceiling with Acoustical Ebony, square edge, Glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 grid system.The T15 Grid system of 600x600mm module shall include wall angle (WA15W30) with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 (MT15W36) having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 (CT15W12) having flange width 15mm, height 32mm and length 1200mm is then interlocked into the pre-cut sLots in the Main T15 at 600mm centers in the direction perpendicular to the Main T15. Finally Cross T15 (CT15W06) having flange width 15mm, height 32mm and length 600mm are then interlocked into the pre cut sLots in the 1200mm Cross T15 at 1200mm centers and in direction parallel to the Main T15. Acoustical Ebony Square edge of size 595x595x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind Acoustical panels are orianted in one direction to achieve uniform shade. Contractor to provide trapdoors as per size and finishes requested by other servicesbased on site condition.Appoved Recommended Makes- Anutone/Amstrong/Ecophone/Equivalent
298
-
-
Auditorium- Supply, Installation & Providing of Side Walls Reflective wall treatment -0.2NRC using Slats diffuse 0.2 NRC made of pinewood fiberboard,Melamine laminated finish, groove perforated slats L16-2 - backlined with black acoustical fleece, tongue-groove edge for a seamless look, of size 128x2440x16mm thick having base density 800Kg/m3, weight 12Kgs/m2 installed by using GI strut system. The GI strut system includes GI Cross channel (CC25) having thickness 0.55mm, length 3600mm, knurled web 50mm, depth 25mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centers. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is then fixed perpendicular to the CC10 with the help of fasteners at every 400mm centers. Slats of size 128x 2430x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs bothways.Panels shall be backlined with acoustical infill of Micro wadding polywool 25mm thickness & 500GSM adhered to the wall using suitable adhesive. Channel support to be considered from wall based on site conditions. Area of treatment will be as per architect & consultant design.Appoved Recommended Makes- Topakustik/ RPG/Anutone/Equivalent
214
-
-
Absorption Treatment - 0.9 NRC
0.01
-
-
Auditorium- Supply, Installation & Providing of Side Walls Absorption Treatment - 0.9 NRC using Stretch NRC wall fabric system by using FR Grade NRC fabric of size 1700mm width, shall be stretched by using CC 50 with infill of 45mm natural cellulose fiber wet spray having density of minimum 90Kgs/m3 , Steadied with Polypropylene Spunbond non woven fabric, backed with 12mm rigid vinyl Stretch Tracks half wrap/full wrap 15mm (FS15) and Midseam 15mm (FS15), with requisite accessories & tools. CC 50 mm is first installed on the wall along with ithe marking lines with metal fasteners inserted at 300mm centers . FS15 tracks to be installed on wooden base, after applying suitable adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks.Natural cellose fibre is sprayed on the wall for a thickness of 45 mm with minimum density of 90Kgs/m3 along with nozel sprayed water and adhesive compond, steadied with polypropylene spunbond non woven fabric backed with high density acoustic polyutheren foam of 50mm thickness and 30 Kgs/m3. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note -minimum 50mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600mm.Channel support to be considered from wall based on site conditions.Area of treatment will be as per architect & consultant design.Appoved Recommended Makes (Cellulouse Fiber)- Enviro 300/Equivalent, Appoved Recommended Makes(Fabric)- Anutone/Atmosphere/Response/Equivalent
278
-
-
Auditorium- Supply, Installation & Providing of Stage side walls treatment with acosutical ebony, magnesite bonded pinewood fibre core tiles of size 600x1200x20mm, density 400 Kgs/m3, weight 8kg/m2 installed by using Strut framework system with non-visible fasteners using Strut H-Spline.The Strut framework systems includes Strut CC50 Cross Channel having thickness 0.7mm, length 3600mm, knurled web 50, depth 50mm and equal flanges 15mm is fastened to wall positioned horizontally in a regular manner at 600mm c/c. Strut H-Spline having sectional thickness 2mm and length 2400mm to be fixed perpendicular to the Strut CC50 Cross Channel at 600mm centers. The Kerfed edge panels shall be then inserted into the Strut H-spline along their long edges of 2400mm against framework to perfect fit with staggered short edges.The system is backlined with the acoustical infill of 50mm thickness & 1000 GSM desity micro wading polywool.Appoved Recommended Makes- Anutone/Amstrong/Heradesign/Equivalent
195
-
-
Auditorium- Supply, Installation & Providing of Stage Wooden flooring with 79mm high, hard wooden flooring on stage.Frame work shall be fabricated by using 50mm high x 50mm wide wooden battens fixed on the stage floor at 600mm centers in both directions, by using suitable fasteners. Contractor to co-ordinate with AV vendor and decide final height to conceal stage floor boxes.Resultant air gap between floor and plywood to be lined by using polyester wool having a density of 1000 GSM and 50mm thick,19mm thick FR Grade high density BWP grade plywood is then fixed to wooden frame rigidly by using suitable fasteners and ensure proper level of the plywood surface and fix wood flooring having wooden finish of 10mm thick above 19mm ply,Flooring to be provided with wood corner profiles towards the edge of the stage along with 200mm high 15mm thick hard wooden skirting along the perimeter of the floor with 3mm foam underlay. Appoved Recommended Makes(BWP Plywood)- Sharon/ Century/Merino/Equivalent
216
-
-
Auditorium- Supplying and fixing of Carpet flooring with 800 Gsm, 100% printed nylon 6 cut pile design roll carpet, total thickness 9mm and roll width in 400 Cm(including 6mm EPE Foam U/Lay and laying).The floor which recieves the carpet to be thourougly cleaned as per manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing , aluminium profile at riser thread and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover/on commissioning. If after the protective layer is removed and stains observed in the carpet because of in adequate protection, the same shall be shampooed and made good to the satisfaction of the project managers. The measurements of carpet will be the actual laid area. Appoved Recommended Makes- Carus/Wilton/Milliken /Equivalent
615
-
-
Auditorium- Supply, Installation & Providing of 2H Fire rate Acoustic Door - Door type: Double Leaf: Door Wall opening: 2000mm(W) x 2400mm(H): Acoustic Doors for 35dB sound insulation (ARAI certified) The doors system duly tested for Integrity and Insulation Criteria as per the IS: 3614 Part-2 and BS: 476 Part: 22 specified in IS:3809-1979 and BS: 476 Part-20 & 22 1987 to achieve the required integrity and insulation Door Frame : Providing of 1st class hard wood frame of section 120 mm x 60 mm with density of 650 kg/meter cube. Shutter: Providing of 50 mm thick smoke check shutter as per BS 476 pART 20 & 22. IS: 3614 Part-II & ISO 834 comprising of Calcium silicate board 9mm and 12mm thick boards, treated hard wood internal timber frame work of 100x 30 mm with minimum 50 mm infill of ceramic fibre/ micro wading polywool, 1000 GSM density with reinforced FR silicate coating on both sides and faced with MDF/ plywood and extremely lipped with hardwood beading. Sealant is used to seal the gap between Calcium silicate board and shutter beading. The door should include SS ball bearing hinge , SS back to back handle , SS Door lock , Door Closure , panic exit device, SS tower bolt , Drop down seal , Fire rated glass vision panel if specified by consultant/architect.
2
-
-
Auditorium- Supply, Installation & Providing of 2H Fire rate Acoustic Door - Door type: Double Leaf: Door Wall opening: 1800mm(W) x 2000mm(H): Acoustic Doors for 35dB sound insulation (ARAI certified) The doors system duly tested for Integrity and Insulation Criteria as per the IS: 3614 Part-2 and BS: 476 Part: 22 specified in IS:3809-1979 and BS: 476 Part-20 & 22 1987 to achieve the required integrity and insulation Door Frame : Providing of 1st class hard wood frame of section 120 mm x 60 mm with density of 650 kg/meter cube. Shutter: Providing of 50 mm thick smoke check shutter as per BS 476 pART 20 & 22. IS: 3614 Part-II & ISO 834 comprising of Calcium silicate board 9mm and 12mm thick boards, treated hard wood internal timber frame work of 100x 30 mm with minimum 50 mm infill of ceramic fibre/ micro wading polywool, 1000 GSM density with reinforced FR silicate coating on both sides and faced with MDF/ plywood and extremely lipped with hardwood beading. Sealant is used to seal the gap between Calcium silicate board and shutter beading. The door should include SS ball bearing hinge , SS back to back handle , SS Door lock , Door Closure , panic exit device, SS tower bolt , Drop down seal , Fire rated glass vision panel if specified by consultant/architect.
2
-
-
Auditorium- Supply, Installation & Providing of auditorium Tip-up recliner chair of center to center 533mm,1020mm height, Plywood (hardwood) with induction heating and high pressure pressed. ABS moulded housing for seat & back cushions,armrest made of PP/PPCP/ABS or semi rigid PU foam. Polyurethane injection moulded flexible foam seat and back density 50 – 55 kg/m3, Fabric to be 100% polyester synthetic fabric with 4 mm polyurethane foam lamination.Fire retardant standard ISO3795, FMVVSS302, Water repellent -Standard -AATCC193. Torsion spring/spring steel IS:4454 1981 Grade III. HRCA/CRCA Sheet metal IS:1079 1994, Electrostatic epoxy powder coating thickness:70 - 80 microns. Seat numbering at side of the chair with LED lights on sides along with aisles.The chairs should be installed to the flooring with the anchor fasteners 12mmx100mm pin type. Fabric colour to customer choice. Appoved Recommended Makes- Feather Lite/ SR/Herman Miller/Equivalent
280
-
-
Auditorium- Supply, Installation & Providing of auditorium Back push recliner chair of center to center 558mm,1020mm height, Plywood (hardwood) with induction heating and high pressure pressed.ABS moulded housing for seat & back cushions,armrest made of PP/PPCP/ABS or semi rigid PU foam. Polyurethane injection moulded flexible foam seat and back density 50 – 55 kg/m3, Fabric to be 100% polyester synthetic fabric with 4 mm polyurethane foam lamination.Fire retardant standard ISO3795, FMVVSS302, Water repellent -Standard -AATCC193. Torsion spring/spring steel IS:4454 1981 Grade III. HRCA/CRCA Sheet metal IS:1079 1994, Electrostatic epoxy powder coating thickness:70 - 80 microns. Seat numbering at side of the chair with LED lights on sides along with aisles.The chairs should be installed to the flooring with the anchor fasteners 12mmx100mm pin type. Fabric colour to customer choice.Appoved Recommended Makes- Feather Lite/ SR/Herman Miller/Equivalent
54
-
-
AV Theater- Supply, Installation & Providing of Acoustical false ceiling with ebony, square edge, Glassfibre core fully encapsulated ceiling tile of size 595x1195x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 grid system.The T15 Grid system of 600x600mm module shall include wall angle (WA15W30) with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 (MT15W36) having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 (CT15W12) having flange width 15mm, height 32mm and length 1200mm is then interlocked into the pre-cut sLots in the Main T15 at 600mm centers in the direction perpendicular to the Main T15. Finally Cross T15 (CT15W06) having flange width 15mm, height 32mm and length 600mm are then interlocked into the pre cut sLots in the 1200mm Cross T15 at 1200mm centers and in direction parallel to the Main T15. Acoustical Ebony Square edge of size 595x51195x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind Acoustical panels are orianted in one direction to achieve uniform shade.Appoved Recommended Makes- Anutone/Amstrong/Ecophone/Equivalent
330
-
-
AV Theater- Supply, Installation & Providing of Side Wall acoustical treatment for 0.9NRC as per drawing using Stretch NRC wall fabric system by using FR Grade NRC fabric of size 1700mm width, shall be stretched by using CC 25 with infill of 25mm natural cellulose fiber wet spray having density of minimum 90Kgs/m3 , Steadied with Polypropylene Spunbond non woven fabric, backed with 12mm rigid vinyl Stretch Tracks half wrap/full wrap 15mm (FS15) and Midseam 15mm (FS15), with requisite accessories & tools. CC 25 mm is first installed on the wall along with ithe marking lines with metal fasteners inserted at 300mm centers . FS15 tracks to be installed on wooden base, after applying suitable adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks.Natural cellose fibre is sprayed on the wall for a thickness of 25 mm with minimum density of 90Kgs/m3 along with nozel sprayed water and adhesive compond, steadied with polypropylene spunbond non woven fabric backed with high density acoustic polyutheren foam of 12mm thickness and 30 Kgs/m3. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Appoved Recommended Makes (Cellulouse Fiber)- Enviro 300/Equivalent, Appoved Recommended Makes(Fabric)- Anutone/Atmosphere/Response./Equivalent
358
-
-
AV Theater- Supply, Installation & Providing of Screen back wall treatment as per drawing using acosutical ebony, magnesite bonded pinewood fibre core tiles of size 600x1200x20mm, density 400 Kgs/m3, weight 8kg/m2 installed by using Strut framework system with non-visible fasteners using Strut H-Spline.The Strut framework systems includes Strut CC50 Cross Channel having thickness 0.7mm, length 3600mm, knurled web 50, depth 50mm and equal flanges 15mm is fastened to wall positioned horizontally in a regular manner at 600mm c/c. Strut H-Spline having sectional thickness 2mm and length 2400mm to be fixed perpendicular to the Strut CC50 Cross Channel at 600mm centers. The Kerfed edge panels shall be then inserted into the Strut H-spline along their long edges of 2400mm against framework to perfect fit with staggered short edges.The system is backlined with the acoustical infill of 50mm thickness & 500GSM desity micro wading polywool.Appoved Recommended Makes- Anutone/Amstrong/Heradesign/Equivalent
126
-
-
AV Theater- Supply, Installation & Providing of Vinyl Flooring as per drawing using 2mm thk Industrial grade Vinyl flooring with Anti -skid ,abrasion resistance , fire proof with hardness Vinyl floor of Recommended Make and shade as per approved sample by Archtiect on leveld and smooth floor surface with any good quality ahesive compuond as suggest by the manufacturer.Appoved Recommended Makes- Armstrong, Gerflor , LG/Equivalent
396
-
-
AV Theater- Supplying and fixing of Carpet flooring as per drawing using 800 Gsm, 100% printed nylon 6 cut pile design roll carpet, total thickness 9mm and roll width in 400 Cm(including 6mm EPE Foam U/Lay and laying).The floor which recieves the carpet to be thourougly cleaned as per manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing , aluminium profile at riser thread and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover/on commissioning. If after the protective layer is removed and stains observed in the carpet because of in adequate protection, the same shall be shampooed and made good to the satisfaction of the project managers. The measurements of carpet will be the actual laid area.Appoved Recommended Makes- Carus/Wilton/Milliken /Equivalent
531
-
-
AV Theater- Supply, Installation & Providing of 2H Fire rate Acoustic Door - Door type: Double Leaf: Door Wall opening: 1800mm(W) x 2000mm(H): Acoustic Doors for 35dB sound insulation (ARAI certified) The doors system duly tested for Integrity and Insulation Criteria as per the IS: 3614 Part-2 and BS: 476 Part: 22 specified in IS:3809-1979 and BS: 476 Part-20 & 22 1987 to achieve the required integrity and insulation Door Frame : Providing of 1st class hard wood frame of section 120 mm x 60 mm with density of 650 kg/meter cube. Shutter: Providing of 50 mm thick smoke check shutter as per BS 476 pART 20 & 22. IS: 3614 Part-II & ISO 834 comprising of Calcium silicate board 9mm and 12mm thick boards, treated hard wood internal timber frame work of 100x 30 mm with minimum 50 mm infill of ceramic fibre/ micro wading polywool, 1000 GSM density with reinforced FR silicate coating on both sides and faced with MDF/ plywood and extremely lipped with hardwood beading. Sealant is used to seal the gap between Calcium silicate board and shutter beading. The door should include SS ball bearing hinge , SS back to back handle , SS Door lock , Door Closure , panic exit device, SS tower bolt , Drop down seal , Fire rated glass vision panel if specified by consultant/architect
2
-
-
AV Theater- Supply, Installation & Providing of Back push recliner chair of center to center 588mm,1100mm height, Plywood (hardwood) with induction heating and high pressure pressed. ABS moulded housing for seat & back cushions,armrest made of PP/PPCP/ABS or semi rigid PU foam. Polyurethane injection moulded flexible foam seat and back density 50 – 55 kg/m3, Fabric to be 100% polyester synthetic fabric with 4 mm polyurethane foam lamination.Fire retardant standard ISO3795, FMVVSS302, Water repellent -Standard -AATCC193. Torsion spring/spring steel IS:4454 1981 Grade III. HRCA/CRCA Sheet metal IS:1079 1994, Electrostatic epoxy powder coating thickness:70 - 80 microns. Seat numbering at side of the chair with LED lights on sides along with aisles. The chairs should be installed to the flooring with the anchor fasteners 12mmx100mm pin type. Fabric colour to customer choice.Appoved Recommended Makes- Feather Lite/ SR/Herman Miller/Equivalent
200
-
-
Blackbox Theater- Supply, Installation & Providing of False Ceiling using acosutical ebony, magnesite bonded pinewood fibre core pigmented ceiling panel of size 600x1200x20mm, volume density 400Kgs/m3, weight 8 kg/m2 installed by using Strut ceiling framework. The Strut ceiling framework system shall include Strut WC25 Wall channel, fully knurled, sectional thickness 0.55mm, length 3600mm, unequal flanges of 20 & 30mm and web of 25mm, fixed along the perimeters of the wall with nylon sleeves and suitable fasteners at every 300mm centers. Then suspend Strut MC45 Main channels, fully knurled, sectional thickness 0.8mm, length 3600mm, equal flanges of 15mm and web 45mm from the soffit at 1200mm centers with Strut SA25, fully knurled, Suspender angle with sectional thickness 0.55mm, unequal flanges of 25 & 10mm. Strut CC25 Cross channel, fully knurled, sectional thickness 0.55mm, length 3600mm, web 35mm, depth of 20mm and equal flanges 9.5mm is fastened to the Strut MC45 perpendicularly at 300mm centers. Strand Ebony is installed on the Strut CC25 with suitable fasteners at 300mm centres. Longer edges of the Strand Ebony should be perpendicular to length of CC25.The system is backlined with the acoustical infill of 25mm thickness & 1000GSM desity micro wading polywool.Appoved Recommended Makes- Anutone/Amstrong/Heradesign/Equivalent
148
-
-
Blackbox Theater- Supply, Installation & Providing of Side Wall acoustical treatment for 0.9NRC as per drawing using Stretch NRC wall fabric system by using FR Grade NRC fabric of size 1700mm width, shall be stretched by using CC 25 with infill of 25mm natural cellulose fiber wet spray having density of minimum 90Kgs/m3 , Steadied with Polypropylene Spunbond non woven fabric, backed with 12mm rigid vinyl Stretch Tracks half wrap/full wrap 15mm (FS15) and Midseam 15mm (FS15), with requisite accessories & tools. CC 25 mm is first installed on the wall along with ithe marking lines with metal fasteners inserted at 300mm centers . FS15 tracks to be installed on wooden base, after applying suitable adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks.Natural cellose fibre is sprayed on the wall for a thickness of 25 mm with minimum density of 90Kgs/m3 along with nozel sprayed water and adhesive compond, steadied with polypropylene spunbond non woven fabric backed with high density acoustic polyutheren foam of 12mm thickness and 30 Kgs/m3. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Appoved Recommended Makes (Cellulouse Fiber)- Enviro 300/Equivalent, Appoved Recommended Makes(Fabric)- Anutone/Atmosphere/Response/Equivalent
179
-
-
Blackbox Theater- Supply, Installation & Providing of 79mm high, hard wooden flooring on stage.Frame work shall be fabricated by using 50mm high x 50mm wide wooden battens fixed on the stage floor at 600mm centers in both directions, by using suitable fasteners. Contractor to co-ordinate with AV vendor and decide final height to conceal stage floor boxes.Resultant air gap between floor and plywood to be lined by using polyester wool having a density of 1000 GSM and 50mm thick,19mm thick FR Grade high density BWP grade plywood is then fixed to wooden frame rigidly by using suitable fasteners and ensure proper level of the plywood surface and fix wood flooring having wooden finish of 10mm thick above 19mm ply,Flooring to be provided with wood corner profiles towards the edge of the stage along with 200mm high 15mm thick hard wooden skirting along the perimeter of the floor with 3mm foam underlay.Appoved Recommended Makes(BWP Plywood)- Sharon/ Century/Merino/Equivalent
35
-
-
Blackbox Theater- Supplying and fixing of Carpet flooring using 580 to 750 Gr/m2, Gauge 1/10 , 100% polypropylene graphic loop pile carpet tile size in 50cm X 50cm.The floor which recieves the carpet to be thourougly cleaned as per manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover/on commissioning. If after the protective layer is removed and stains observed in the carpet because of in adequate protection, the same shall be shampooed and made good to the satisfaction of the project managers. The measurements of carpet will be the actual laid area.Appoved Recommended Makes- Carus/Wilton/Milliken /Equivalent
120
-
-
Blackbox Theater- Supply, Installation & Providing of 2H Fire rate Acoustic Door - Door type: Double Leaf: Door Wall opening: 1800mm(W) x 2100mm(H): Acoustic Doors for 35dB sound insulation (ARAI certified) The doors system duly tested for Integrity and Insulation Criteria as per the IS: 3614 Part-2 and BS: 476 Part: 22 specified in IS:3809-1979 and BS: 476 Part-20 & 22 1987 to achieve the required integrity and insulation Door Frame : Providing of 1st class hard wood frame of section 120 mm x 60 mm with density of 650 kg/meter cube. Shutter: Providing of 50 mm thick smoke check shutter as per BS 476 pART 20 & 22. IS: 3614 Part-II & ISO 834 comprising of Calcium silicate board 9mm and 12mm thick boards, treated hard wood internal timber frame work of 100x 30 mm with minimum 50 mm infill of ceramic fibre/ micro wading polywool, 1000 GSM density with reinforced FR silicate coating on both sides and faced with MDF/ plywood and extremely lipped with hardwood beading. Sealant is used to seal the gap between Calcium silicate board and shutter beading. The door should include SS ball bearing hinge , SS back to back handle , SS Door lock , Door Closure , panic exit device, SS tower bolt , Drop down seal , Fire rated glass vision panel if specified by consultant/architect
2
-
-
Blackbox Theater- Supply, Installation & Providing of Fixed arms medium back black coloured chair made of polypropylene with mesh Upholstery & foam padding base. Chair height of 940mm, seat width 470mm, seat height 520mm, back width 500mm & arm length 250mm.To be approved by architect/consultant.
100
-
-
Seminar Hall- Supply, Installation & Providing of False ceiling using acoustical glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 grid system.The T15 Grid system of 600x600mm module shall include wall angle (WA15W30) with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 (MT15W36) having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 (CT15W12) having flange width 15mm, height 32mm and length 1200mm is then interlocked into the pre-cut sLots in the Main T15 at 600mm centers in the direction perpendicular to the Main T15. Finally Cross T15 (CT15W06) having flange width 15mm, height 32mm and length 600mm are then interlocked into the pre cut sLots in the 1200mm Cross T15 at 1200mm centers and in direction parallel to the Main T15. Square edge of size 595x595x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind Acoustical panels are orianted in one direction to achieve uniform shade.Appoved Recommended Makes- Anutone/Amstrong/Ecophone/Equivalent
158
-
-
Seminar Hall- Supply, Installation & Providing of Side Walls treatment as per drawing using Wooden Slats diffuse 0.2 NRC made of pinewood fiberboard,Melamine laminated finish, groove perforated Wooden Slats L16-2 - backlined with black acoustical fleece, tongue-groove edge for a seamless look, of size 128x2440x16mm thick having base density 800Kg/m3, weight 12Kgs/m2 installed by using GI strut system. The GI strut system includes GI Cross channel (CC25) having thickness 0.55mm, length 3600mm, knurled web 50mm, depth 25mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centers. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is then fixed perpendicular to the CC10 with the help of fasteners at every 400mm centers. Wooden Slats of size 128x 2430x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs bothways.Panels shall be backlined with acoustical infill of acoustical infill of Micro wadding polywool 25mm thickness & 500GSM adhered to the wall using adhesive.Appoved Recommended Makes- Topakustik/ RPG/Anutone/Equivalent
78
-
-
Seminar Hall- Supply, Installation & Providing of Side walls treatment as per drawing using Stretch NRC wall fabric system by using FR Grade NRC fabric of size 1700mm width, shall be stretched by using CC 25 with infill of micro wadding polywool , rigid vinyl Stretch Tracks half wrap/full wrap 15mm (FS15) and Midseam 15mm (FS15), pinewood fiber strand board, micro wadding polywool infill with requisite accessories & tools. CC 25 mm is first installed on the wall along with ithe marking lines with metal fasteners inserted at 300mm centers . FS15 tracks to be installed on wooden base, after applying adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks. Strand square edge magnesite bonded pinewood fiber panels of size 600x1200x20mm having density 400kg/m3, weight 4kg which is fixed to wall with suitable fasteners. Micro wadding polywool of 1000 GSM density ,25mm thickness adhered on strand panel by using adhesive. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Note -minimum 50mm additional fabric is required for tucking hence maximum module wall fabric width would be 1600mm.Appoved Recommended Makes- Anutone/Amstrong/Ecophone
168
-
-
Seminar Hall- Supply, Installation & Providing of Vinyl flooring using 2mm thk Industrial grade Vinyl flooring with Anti -skid ,abrasion resistance , fire proof with hardness Vinyl floor of Recommended Make and shade as per approved sample by Archtiect & Consultant.
165
-
-
Auditorium- Supply, Installation & Providing of 2H Fire rate Acoustic Door - Door type: Double Leaf: Door Wall opening: 2000mm(W) x 2400mm(H): Acoustic Doors for 35dB sound insulation (ARAI certified) The doors system duly tested for Integrity and Insulation Criteria as per the IS: 3614 Part-2 and BS: 476 Part: 22 specified in IS:3809-1979 and BS: 476 Part-20 & 22 1987 to achieve the required integrity and insulation Door Frame : Providing of 1st class hard wood frame of section 120 mm x 60 mm with density of 650 kg/meter cube. Shutter: Providing of 50 mm thick smoke check shutter as per BS 476 pART 20 & 22. IS: 3614 Part-II & ISO 834 comprising of Calcium silicate board 9mm and 12mm thick boards, treated hard wood internal timber frame work of 100x 30 mm with minimum 50 mm infill of ceramic fibre/ micro wading polywool, 1000 GSM density with reinforced FR silicate coating on both sides and faced with MDF/ plywood and extremely lipped with hardwood beading. Sealant is used to seal the gap between Calcium silicate board and shutter beading. The door should include SS ball bearing hinge , SS back to back handle , SS Door lock , Door Closure , panic exit device, SS tower bolt , Drop down seal , Fire rated glass vision panel if specified by consultant/architect.
1
-
-
Seminar Hall- Supply, Installation & Providing of Fixed arms medium back black coloured chair made of polypropylene with mesh Upholstery & foam padding base. Chair height of 940mm, seat width 470mm, seat height 520mm, back width 500mm & arm length 250mm.To be approved by architect/consultant
70
-
-
Mixing Room- Supply, Installation & Providing of False ceiling using acoustical glassfibre core fully encapsulated ceiling tile of size 595x595x15mm having density 100-120Kgs/m3, weight 1.5-1.8kg/m2 which is suspended by using 0.3mm thick and 15mm wide pre coated metal T15 grid system.The T15 Grid system of 600x600mm module shall include wall angle (WA15W30) with unequal flanges of size 14&20mm wide, length 3000mm, 0.43mm thick fixed along the perimeter of walls with the help of nylon sleeves and suitable fasteners at 300mm centers. Then suspend the Main T15 (MT15W36) having flange width 15mm, height 32mm and length 3600mm from the soffit with help of soffit cleat and wire rod with leveling spring clip at 1200mm c/c. Cross T15 (CT15W12) having flange width 15mm, height 32mm and length 1200mm is then interlocked into the pre-cut sLots in the Main T15 at 600mm centers in the direction perpendicular to the Main T15. Finally Cross T15 (CT15W06) having flange width 15mm, height 32mm and length 600mm are then interlocked into the pre cut sLots in the 1200mm Cross T15 at 1200mm centers and in direction parallel to the Main T15. Square edge of size 595x595x15mm thick shall be placed into the grid size of 600x600mm. Ensure arrow marks behind Acoustical panels are orianted in one direction to achieve uniform shade.Appoved Recommended Makes- Anutone/Amstrong/Ecophone/Equivalent
122
-
-
Mixing Room- Supply, Installation & Providing of Side Walls treatment as per drawing using Wooden Slats diffuse 0.2 NRC made of pinewood fiberboard,Melamine laminated finish, groove perforated Wooden Slats L16-2 - backlined with black acoustical fleece, tongue-groove edge for a seamless look, of size 128x2440x16mm thick having base density 800Kg/m3, weight 12Kgs/m2 installed by using GI strut system. The GI strut system includes GI Cross channel (CC25) having thickness 0.55mm, length 3600mm, knurled web 50mm, depth 25mm and equal flanges 15mm is fastened vertically/horizontally at every 600mm centers. Aluminium core cross channel (CC18) having thickness 0.5mm, length 2400mm, web 15mm & 27mm, depth 18mm and flanges of 7mm with suitable edge & centre brackets is then fixed perpendicular to the CC10 with the help of fasteners at every 400mm centers. Wooden Slats of size 128x 2430x16mm in then fixed perpendicular to CC18 with suitable edge & centre brackets. Contractor to provide expansion joints of 3mm at every 5mtrs bothways.Panels shall be backlined with acoustical infill of acoustical infill of Micro wadding polywool 25mm thickness & 500GSM adhered to the wall using adhesive.Appoved Recommended Makes- Topakustik/ RPG/Anutone/Equivalent
78
-
-
Mixing Room- Supply, Installation & Providing of Side Wall acoustical treatment for 0.9NRC as per drawing using Stretch NRC wall fabric system by using FR Grade NRC fabric of size 1700mm width, shall be stretched by using CC 25 with infill of 25mm natural cellulose fiber wet spray having density of minimum 90Kgs/m3 , Steadied with Polypropylene Spunbond non woven fabric, backed with 12mm rigid vinyl Stretch Tracks half wrap/full wrap 15mm (FS15) and Midseam 15mm (FS15), with requisite accessories & tools. CC 25 mm is first installed on the wall along with ithe marking lines with metal fasteners inserted at 300mm centers . FS15 tracks to be installed on wooden base, after applying suitable adhesive on both surfaces for a true and continuous secure grip, and heavy-duty fasteners at 150mm centers on one/both sides of Stretch Tracks.Natural cellose fibre is sprayed on the wall for a thickness of 25 mm with minimum density of 90Kgs/m3 along with nozel sprayed water and adhesive compond, steadied with polypropylene spunbond non woven fabric backed with high density acoustic polyutheren foam of 12mm thickness and 30 Kgs/m3. Fabric of width 1700mm is then aligned to the Stretch tracks by following the fabric thread line or pattern. The fabric is stretched and tucked into the Stretch tracks and secure into the locking jaws so that it will be smooth, free of wrinkles with the tucking tools. Appoved Recommended Makes (Cellulouse Fiber)- Enviro 300/Equivalent, Appoved Recommended Makes(Fabric)- Anutone/Atmosphere/Response./Equivalent
132
-
-
Mixing Room- Supplying and fixing of Carpet flooring with 800 Gsm, 100% printed nylon 6 cut pile design roll carpet, total thickness 9mm and roll width in 400 Cm(including 6mm EPE Foam U/Lay and laying).The floor which recieves the carpet to be thourougly cleaned as per manufacturer's specification. The carpet is to be laid over a bed of manufacturer's approved adhesive spread evenly over the entire floor. The rate shall include cutting, trimming, fixing , aluminium profile at riser thread and clearing away of residual material to a location as directed. The rate shall also include supplying and laying of a protective layer of PVC or HDPE sheet of 50 microns thickness, held together with scotch tape. The laid carpet to be vacuumed after the removal of protective cover/on commissioning. If after the protective layer is removed and stains observed in the carpet because of in adequate protection, the same shall be shampooed and made good to the satisfaction of the project managers. The measurements of carpet will be the actual laid area. Appoved Recommended Makes- Carus/Wilton/Milliken /Equivalent
120
-
-
Mixing Room- Supply Installation Testing & Commissioning of 2H Fire rate Acoustic Door - Door type: Single Leaf: Door Wall opening: 1086 mm(W) x 2100mm(H): Acoustic Doors for 35dB sound insulation (ARAI certified) The doors system duly tested for Integrity and Insulation Criteria as per the IS: 3614 Part-2 and BS: 476 Part: 22 specified in IS:3809-1979 and BS: 476 Part-20 & 22 1987 to achieve the required integrity and insulation Door Frame : Providing of 1st class hard wood frame of section 120 mm x 60 mm with density of 650 kg/meter cube. Shutter: Providing of 50 mm thick smoke check shutter as per BS 476 pART 20 & 22. IS: 3614 Part-II & ISO 834 comprising of Calcium silicate board 9mm and 12mm thick boards, treated hard wood internal timber frame work of 100x 30 mm with minimum 50 mm infill of ceramic fibre/ micro wading polywool, 1000 GSM density with reinforced FR silicate coating on both sides and faced with MDF/ plywood and extremely lipped with hardwood beading. Sealant is used to seal the gap between Calcium silicate board and shutter beading. The door should include SS ball bearing hinge , SS back to back handle , SS Door lock , Door Closure , panic exit device, SS tower bolt , Drop down seal , Fire rated glass vision panel if specified by consultant/architect
2
-
-
Mixing Room- Supply, Installation & Providing of auditorium Back push recliner chair of center to center 558mm,1020mm height, Plywood (hardwood) with induction heating and high pressure pressed.ABS moulded housing for seat & back cushions,armrest made of PP/PPCP/ABS or semi rigid PU foam. Polyurethane injection moulded flexible foam seat and back density 50 – 55 kg/m3, Fabric to be 100% polyester synthetic fabric with 4 mm polyurethane foam lamination.Fire retardant standard ISO3795, FMVVSS302, Water repellent -Standard -AATCC193. Torsion spring/spring steel IS:4454 1981 Grade III. HRCA/CRCA Sheet metal IS:1079 1994, Electrostatic epoxy powder coating thickness:70 - 80 microns. Seat numbering at side of the chair with LED lights on sides along with aisles.The chairs should be installed to the flooring with the anchor fasteners 12mmx100mm pin type. Fabric colour to customer choice.Appoved Recommended Makes- Feather Lite/ SR/Herman Miller/Equivalent
10
-
-
Auditorium- Supply Installation Testing & Commissioning of LEFT Line Array Speakers with the following specifications, 3 Way line array Speaker Dual Low Frequency (LF) 8" drivers, Continuous power 85W @HF,250W@MF, 250W@LF, Maximum Peak Output 133dB SPL @HF &128dB SPL @ LF&MF Or better Sensitivity Output HF @ 108dB SPL LF @ 98 dB SPL & MF 98 db Or better , Frequency Response 68 Hz - 18 kHz Or better , Nominal Coverage Horizontal 140 degree Vertical 10 degree or Better , Nominal Impredance 16 Ohm for HF/LF/MF or better. Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Right Line Array Speakers with the following specifications, 3 Way line array Speaker Dual Low Frequency (LF) 8" drivers, Continuous power 85W @HF,250W@MF, 250W@LF, Maximum Peak Output 133dB SPL @HF &128dB SPL @ LF&MF Or better Sensitivity Output HF @ 108dB SPL LF @ 98 dB SPL & MF 98 db Or better , Frequency Response (±3 dB) 68 Hz - 18 kHz Or better , Nominal Coverage Horizontal 140 degree Vertical 10 degree or Better , Nominal Impredance 16 Ohm for HF/LF/MF or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Flying Subwoofer with the following Specification Single Dual 12" Woofer,Maximum Power 1100Watts ,Frequency Response (±3 dB) 40 Hz - 100 Hz,, Nominal Impredance 4 .Recommended Make:BOSE /QSC / L -Acoustics /EquivalentOhm, Sensitivity Output LF @ 98 dB SPL Maximum SPL 135dB or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Active Front fill Speaker with the following Specification 1800 W active Class D Amplifier with inbuild DSP, 8-inch LF Driver; 1.4-inch HF driver; 105 degree Axisymetric Coverage angle OR 105 H X 100 V or better coverage ,Frequency Response 59 Hz - 20 kHz, Maximum Peak SPL 128 or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of Active Stage Monitor with following Specification 2000W Class D Amplifier with inbuild DSP, 12 inch LF Driver& 1.4" HF Driver ,Frequency Response50 Hz - 20 kHz, Maximum SPL 132dB, Axisymetric Coverage angle 75 Degree Or 75 H X 60 V or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Green & Control Room speaker with following Specification 4.5" Driver 2 Way Speaker , Rated Power 16watts , frequency range 70 Hz–20 kHz, Sensitivity 85 dB SPL , Coverage angle 130 degree Conical , Maximum Peak SPL 103 dB, Impedance 8 ohm,Transformer taps 70V/100V tapping with 8 ohm bypass or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Large Aluminum Array Frame for the Line Array Speaker in Black or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Powder coated steel yoke for mounting the Front fill speaker vertically/Horizontally to structures or better.Recommended Make:BOSE /QSC / L -Acoustics /Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of Class D Amplifier with following Specification , Class D Amplifier with 4 channel independently at 1200 watts/ch at 8Ω, 2000 watts/ch at 4Ω, 1600 watts/ch at 2Ω, 1250 watts/ch , bridged mode @ 4000 Watts 8 Ohm, Frequency response 20 Hz–15 kHz ±0.2 dB 20 Hz–20 kHz +0.2/-0.7 dB, Damping Factor 150 , Input Impedance 10K ohm or better Recommended Make :BOSE /QSC / L -Acoustics /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Class D amplifier with following Specification 4 Channel class D amplifier ,60Watts/Ch @8 ohm & 4 Ohm, Bridged Mode 200Watts @8 Ohm & 4 Ohm, 250Watts @70/100V ,Signal to Noise Ratio 100dB,Frequency Response 20 Hz - 20 kHz,Input Impedance 10 kΩ or better Recommended Make :BOSE /QSC / L -Acoustics /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Signal Processing with following Specification 24 local I/O channels, Dedicated 8 Input & 8 output , Expandable upto 128x128 network I/O channels, telephone POTS, General Purpose Input 16 output 16 , 16 AEC channels, LAN Port x2, USB B type port ,RS232 or better Recommended Make :BOSE /QSC / L -Acoustics /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Mixer with following specification 7” (800x480 pixel) colour touch screen for quick control,32 Mono mic/Line Input , Stereo input , 24 Mix Output , 2 Stereo Out ,Dedicated stereo FX return channels,Automatic Mic Mixing ,Input processing – Preamp, HPF, Gate, PEQ, Compressor,Delay, Channel Ducker or better Recommended Make : Digico /Allen & heath/ Midas/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Wireless Hand Held microphone with RF Carrier Range 174–216; 470–937.5MHz, Working Range 100 Meter,Latency 2.9 ms, Frequency Response 20 Hz – 20 kHz (±1 dB), THD 0.1%, AES-256 encryption for secure wireless transmission , 24-bit digital audio,Maximum Input Level 145 dB SPL Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Wireless Receiver with 64 Mhz Tunning Bandwidth , AEC with 256 bit encryption, Impedance 50 Ohm,Network Address Capability DHCP /Manual IP , Phantom Power Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Wireless Bodypack Transmitter for lapel & Headworn Mic with Frequency Response 20 Hz to 20 kHz ,AES 256-bit encryption for secure transmission,Impedance 50Ω,Maximum Input Level 8.5dBV, Supports 100 Meter Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Wireless Receiver with 64 Mhz Tunning Bandwidth , AEC with 256 bit encryption, Impedance 50 Ohm,Network Address Capability DHCP /Manual IP , Phantom Power Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Wireless Lapel Mic with Condenser , Frquency Response 50 to 20000Hz, Polar pattern Omnidirectional, Uniform with frequency, Impedance 3000 Ohm or better Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Wireless Headworn Mic with Condenser , Polar Pattern Omni Directional Frequency Response 20 hz to 20Khz Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Active Directional Antenna with Frequency Range 470-900Mhz , Impedance 50 Ohm, Reception Pattern 70 degree, RF Overload LED Threshold -5dBm Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Antenna Distribution System with Wideband UHF RF Frequency Range (470-952 MHz) ,Four-way active antenna splitter, impedance 50 Ohm, Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Vocal Microphone with ON/OFF Switch , Frequency Response 50 to 15000 Hz, Uni dirctional Polar Cardiod pattern, Rated Impedance 150 Ohm Recommended Make : Beyerdynamic/Shure/Revolabs/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of Gooseneck Condenser Microphone with frquency Response 50 to 17000 Hz, Impedance 180 Ohm, Phantom Power 11 to 52 Vdc, 2.0 mA Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Mic stand Big for Wired Handheld Microphone with adjustable Type Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Mic stand Small for Wired Handheld Microphone with adjustable Type Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of 4 Channel Junction Box Recommended Make : Custom
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Wired Headphone for control room controller Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of DLP Projector with following Specification Single Chip DLP Projector , 9000 ANSI , WQXGA Resolutions 2560x1600 , Up to 4K UHD @ 60Hz,24/7 Operation,Contrast Ratio 1200:1, Aspect Ratio 16:10,Motorized zoom, focus, vertical and horizontal shift,Orientation 360° rotation,Connectivity Inputs HD SDI, 2x DP 1.2, 2x dual link DVI-D, HDBaseT, HDMI 2.0*, RJ 45 Ethernet, RS232 in, 2x USB, ,Control IR, RS232, RJ45 with Appropriate long throw lens or better Recommended Make : NEC /Barco / Digital Projection/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Projecor Mounting KIT Recommended Make : Custom /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 320" Diagnol Motorized Screen with Heavy Duty Tubular Motor with limit Adjustment facility.Motor is equipped with Auto Cut to avoid motor from burning,Comes with RF Remote and Control Panel with Relay and Rs232/485 control as Optional.Gain More Then 1.5,Pentagon Casing with Inner SS pipe used.Recommended Make : Suvira/Draper/Da-lite/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 55 " LED FHD Display with 16/7 Operation, 350 nits Brightness , Contrast ratio 5000:1,Viewing Angle 178/178 Degree, Inbuild Speaker 10 watts,Connectivity VGA, DVI-D, HDMI,USB , Audio IN/Out, RS232, IR or better Recommended Make : Samsung/NEC/Barco/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of 43 " LED FHD Display with 16/7 Operation, 350 nits Brightness , Contrast ratio 5000:1,Viewing Angle 178/178 Degree, Inbuild Speaker 10 watts,Connectivity VGA, DVI-D, HDMI,USB , Audio IN/Out, RS232, IR or better Recommended Make :Samsung/NEC/Barco/Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of Wall mount bracket for LED Display Recommended Make : Custom /Equivalent
4
-
-
Auditorium- Supplying and fixing of Wooden Podium made with with Gooseneck microphone connectivity, Reading light & Podium PC with extended Keyboard and Mouse Tray for keeping Laptop. As per drawing. Recommended Make : Custom/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Core i5-7500, 4GB DDR4 RAM, Intel 7th Gen Core i3/i5/i7 processor IntelH110Chipset ,Support for discrete NVIDIA/AMD graphic card , DDR4 memory expandable upto 32GB, 8USB ports, 2 independent displays with VGA and HDMIconnectivity 1TB HDD, W10Pro, for Control Room.Recommended Make : HP/Dell /Lenova/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 24inch FHD monitor with 1920x1080 resolution having VGA & HDMI ports, aspect ratio 16:9 ,for Control Room.Recommended Make : Samsung/LG/Benq /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 4K Active Wall plate with following Specification HDMI/VGA Auto Switching Transmitter with HDBT output and Receiver Kit with PoE (4K: 70m/230ft | 1080p: 100m/328ft) ,3840x2160p @30Hz 8bit 4:4:4, HDCP ,3D Compliant,Multichannel audio Dolby Atmos and DTS:X Control RS 232,IR, LANor better Recommended Make : Lightware /Wyrestorm/Extron /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of 4K Presentation Auto Switcher with following Specification 4x1 Scaler switcher , 3840x2160p @30Hz 4:4:4 8bit (70m/230ft), 100 Meter @ 1080P, Connectivity HDMIx2/Display Port/VGA over HDBaseT with CEC control, Scaled Mirrored Output with Balanced Audio, Control Port RS232 Front Panel or better Recommended Make : Lightware /Wyrestorm/Extron /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 4K HDR HDMI Matrix Switcher with Following Specification 6 HDMI input , 6 HDBT out ,4 HDMI mirrored Out, 3840x2160p @30Hz 4:4:4 8bit (70m/230ft) , @24Hz 4:2:0 HDR 10bit (70m/230ft), 2ch PCM ,Up to DTS-X and Dolby Atmos, Communication Control RS232,IR,Ethernet, ARC, HDCP & EDID Compliants or better Recommended Make : Lightware /Wyrestorm/Extron /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of HDBaseT 4K UHD Receiver with following Specification HDBT in & HDMI Out (,3840x2160p @30Hz 4:4:4 24bit (70m/230ft) | @24Hz 4:2:0 HDR 10bit per channel (70m/230ft),Multichannel audio supports 7.1 DTS Master HD and Dolby True HD, HDCP ,EDID Compliant or better Recommended Make : Lightware /Wyrestorm/Extron /Equivalent
5
-
-
Auditorium- Supply Installation Testing & Commissioning of VGA to HDMI Scaler with following Specification , Supporting maximum Resolutions 1920x1200, Connectivity VGA+A IN ,HDMI Out or better Recommended Make : Aten/NT/Logic/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Wireless Presenter Pointer with Following specification ,2.4 GHz Multifunction wireless presenter with Trackball mouse and Pointer or better Recommended Make : Logic/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Fixed PTZ Camera with following Specification 1/2.8" progressive Scan CMOS sensor, 2.14 Megapixel ,30X optical Zoom, Supporting Video Format 1080p 59.94/50/29.97/25,1080i 59.94/50,720p 59.94/50,480i, 576i (on CVBS), White Balance Indoor/Outdoor/Fluorescent/AWB/MWB, Auto & Manual Focus,Pan 270 Degree, Tilt +90 Degree -20 Degree, Presets 50, Focul Length f=4.3mm wide to 129mm TELE ,Connectivity 3G-SDIx1, HDMIx1,CVBSx1 , Protocol VISCA DVIP or better Recommended Make : Datavideo/AJA/Space /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Video Switcher with following Specification 6-CH HD/SD Input, 2 x HDMI inputs ,Control Rs232/RS422 , Audio Input x4, Audio Outputx4,Supported Video Format 1080i 50/59.94/60Hz, 720p 50/59.94/60 Hz, 576i 50Hz, 480i 59.94Hz , Outputs of 6-CH SDI for AUX, PGM, PVW, PGM Clean, Title or Multi-viewer, 2-CH HDMI multi-viewer, Two PIP display, DSK and Luma-Key,Logo Insertion, Effects FTB, Cut, 8 Wipe, Preview PIP & DSK Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Joystick Control Unit with following Specification total 4 preset position for each camera, Control Protocol Sony Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Balanced/Unbalanced input Audio Delay Box for up to 700ms (17 frames) audio delay calibration, Volume attenuating 0 ~ 60dBConnectivity Audio Input XLRx3,RCAx2, Audio Output XLRx2, RCAx2 or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Hard Drive Video Recorder with following Specification HD/SD-SDI, time code & Audio Interface. SDI/HDMI outputs.Supports up to 120Mbps HD-SDI I-frame recording, 4:2:2 sampling, record MOV/MXF file format. *Comes with 2xHE-1 1TB Media Cartridge. (Each cartridge support 10 to 40 hours HD/SD recording time). Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 3G/HD/SD SDI to HDMI Converter with following specification Connectivity 1x 3G/HD/SD-SDI as input ,HDMI Output , Audio IN/Out, Supported up to 1080 50P/59.94P/60P, Equalizer& Reclock the signal or better Recommended Make : Datavideo/AJA/Space /Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Multiformat Converterwith following Specification VGA to3G/HD/SD SDI Converter Connectivity VGAx1,HDMIx1,3G/HD/SD SDI as input & HDMIx1,3G/HD/SD SDI x2, Supported Video Format 1080p , (23.98/24/25/29.97/30/50/59.94/60Hz), Equalizer & reclock the signal or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Video Streaming Server & recorder with Following Specification , Network Video Streaming Server (H.264), Bitrate 6 Mbit ,Network feature DHCP Client, RTSP over TCP/UDP/HTTP with MPEG TS. RTMP, HLS protocols ,Supported Video Resolution
1080 @ 50P / 59.94P / 60P ,Up to 20Mbps streaming & 30Mbps recording format, 2-CH AAC Audio or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Control Processor for all AV Devices with SDRAM 1GB, Flash 4 GB, Memmory card support upto 32GB, External storage supports upto 1TB, RS232 x4, RS422/Rs485x2, IR port x8, Relay x8,LAN,, USB,I/O x8 & Control Cards with 3 Com Port (RS232/RS422/RS485) Recommended Make : Crestron/AMX/Extron/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 9.7 inch Touch Panel for Control Processor or better Recommended Make : Apple/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Docking Station for IPAD or better Recommended Make : Logic/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 24 Port Gigabit Manged Switch or better Recommended Make : Linksys/Dlink /Netgear/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Wireless Router for accessing & Controlling of Device or better Recommended Make : Linksys/Dlink /Netgear/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 32 U Rack with Accessories for Video Equipment or better Recommended Make : Custom/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 1.8 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron/Equivalent
9
-
-
Auditorium- Supply Installation Testing & Commissioning of 3 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron/Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of 10 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 1.8 Meter VGA+A Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of 3 Meter VGA+A Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of 2.5 Sq.mm Speaker Cable for Line array Speakers in meter or better Recommended Make : Belden /KLotz/Chetan/Equivalent
1000
-
-
Auditorium- Supply Installation Testing & Commissioning of 4 Sq Mm Speaker Cables for Subwoofers in meter or better Recommended Make : Belden /KLotz/Chetan/Equivalent
200
-
-
Auditorium- Supply Installation Testing & Commissioning of 2 Core Microphone cable in meter or better Recommended Make : Belden /KLotz/Chetan/Equivalent
200
-
-
Auditorium- Supply Installation Testing & Commissioning of Catx Cable 300 Meter Spool (It may vary depends upon site condition) Recommended Make : Kramer/ NT /Dlink /Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Shielded RJ45 Conenctor (Pack of 10) Recommended Make : Kramer/ NT /Dlink /Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of Control Cable in meter Recommended Make : Kramer/ NT /Dlink /Equivalent
100
-
-
Auditorium- Supply Installation Testing & Commissioning of Serial Digital Interface Camera Cable in meter Recommended Make : Kramer/ NT /Belden/Equivalent
500
-
-
Auditorium- Supply Installation Testing & Commissioning of Floor Box/ Mounting Clamp based on site condition Recommended Make : Custom/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Wall Plate Customizable Back Box or better Recommended Make : Custom/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of 4 channel 60 Mtrs snake cable in meter Recommended Make :Imported/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Assorted Cable , Connectors & Conduiting Recommended Make : Custom/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of High quality LED PAR RGBW Light used as a Effect Light, Spot Light and Strobe
Light etc., with below specifications: Lamp: 54 X 3W RGBW LED (12R+18G+18B+6W),Power consumpsion:162W ,Power supply: 100-230V AC, 50/60Hz , Power cable: 3 core 1.5 sq. mm. copper PVC insulated, Channels: 8 Channel DMX-512, Beam angle: 25° ,Control mode: DMX, and Manual, LUX @ 2m: 11,000, Function: strobe, dimming, sound active,Dimming: 0 - 100%, Housing: Diecast aluminium with black epoxey polyster powder coated, Power and DMX: Loop in and loop out , Dimension: W 220 x L 240 x H 335mm, Weight: 2.9 Kg , Certification: CE Recommended Make : Robe / Martin / Canara lighting/Equivalent
10
-
-
Auditorium- Supply Installation Testing & Commissioning of High quality COB LED 2x2 blinder matrix Light is used in Entertainment applications, Night club, Fashion shows, Film, Band performances, Discotheque, Stage performance , TV studio and large-scale show etcCanara fixture with advanced COB LED technology with below specifications:-Power Consumption: 400W ,Power Supply: 100-230V AC, 50-60Hz, Light Color: Single color warm white (3200K), LEDs Qty : 4 pieces, Channel: 4/8 channel , Lifetime: Over 50,000 hours , Beam Angle: 30 degree , Control mode: DMX512,Master/Slave, Auto Run, Sound active. Dimmer: 0~100% linearly adjustable , LUX: 8270 LUX @ 2m ,IP Grade: IP20 , Dimension: 117 x 350 x 382 mm , Net Weight: 7 Kgs, Certification: CE, Recommended Make : Selecon / ETC / Canara lighting/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of 1000W CE Certified halogen Fresnel spot light providing illumination of 28000 lix at 2 mt in spot at 10° beam angle while 4600 lix at 2 mt when operated in flood at 48° beam angle , dimension as 290 x 405 x 290mm, 150mm aid German lens, weight of 4.6Kg, Gx9.5 base lamp socket,power cord with 16amps 3 pin CE plug and normal yoke but without lamp and accessories. Lamp - 1000W 230V single ended lamp Power supply - 230-240V AC,Lamp Socket - Gx9.5,Housing - Light weight, rugged and reliable both indoor and outdoor,Robust per-treated fabricated housing with die cast component and epoxy polyester,Distribution - Delivers smooth uniform field across the entire spread from spot to flood focusing,Switching options - Local control and Digital DMX control through Dimmer,Dimming option - Digital DMX control through Dimmer,Reflector - Spherical high reflective aluminum anodized,Yoke - Fabricated using MS flat-accepts mounting on 16mm spud,Focus - controlled by front & rear thermoplastic knob. Recommended Make : Desisti / ARRI / Canara lighting/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of 19°, 750W stage profile spot light powder coated diecast body with below specification
Lamp 750W HPL Beam spread 19° , 6432 lux at 5mtr , Weighing 6.2Kg, Dichroic reflector, G9.5 lamp base, 4 Beam shaping shutters,Normal yoke with adjustable keys for tilt rotation ,Fine adjustment in lamp focus position for adjustment.Dimension of 560 x 340 x 430mm. Recommended Make : Spotlight/LDR/Canara lighting/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of 1000W mini flood light under gone through 7 tank process with various chemnical teartment to keep them rust free made out of CRCA fabricated housing which is perforated from top and bottom for effective and efficient ventilation on vertical and horizontal axis for natural flow of air to provide sufficient cooling and built in very sturdy and capable of withstanding rough handling,power cord with 16amps CE plug and normal yoke but without lamp and technical specifications as below.Housing - MS fabricated construction with black epoxy polyester powder coated.Reflector - Aluminum reflector, sand blast anodised aluminum.Lamp type - 1000W tungsten halogen lamp, base R7s,Lamp Socket -R7s,Dimming option- 0-100% using Digital DMX control through Dimmer,Protection rating - IP20,Power supply - 230/240V AC,Power cable - 3 core 1.0 sq. mm. copper PVC insulated cable with 10A DPST toggle switch.Dimension - 376x267x150mm. Recommended Make : Desisti/ARRI/Canara lighting/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of 1000W spun aluminum PARCAN made out of spun aluminum 16 SWG in 2 piece cylindrical construction with punched sLot on Par can housing for natural ventilation and floating ceramic GX16d base lamp socket,Yoke made of MS flat 25 X 3mm with 13mm free mounting hole to fit the adapter, spigot with 28mm and filter frame but without lamp. "Lamp: 1000W 240V PAR-64,Lamp Socket: Ceramic type GX 16D,Housing: Aluminum sheet cylindrical construction with black epoxy polyester "Switching options: Local control and Digital DMX control through Dimmer,Dimming option: Digital DMX control through Dimmer,Yoke: Fabricated using MS flat-accepts mounting on 28mm spud Focus: Sealed beam angle,Accessories: Filter frame. Recommended Make : Desisti / ARRI / Canara lighting/Equivalent
16
-
-
Auditorium- Supply Installation Testing & Commissioning of Diecast aluminum "C" clamp with safety locking chain, duly powder coated in black matt texture finish and technical specifications as below.
Lock - MS threaded Galvanized lock key, Plastic Glass filled nylon moulded M6 key. Receptacle - 28mm standard TV spigot,Safety - MS Galvanized chain with pin, Finish - Pretreated and black epoxy polyester powder coated,Self weight - 0.54Kg , Safe working load – 150Kg. Recommended Make : Canara Lighting / ARRI / Desisti/Equivalent
44
-
-
Auditorium- Supply Installation Testing & Commissioning of Safety bond with lock clip to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly . SWL 100Kgs. Recommended Make : Canara Lighting / ARRI / Desisti/Equivalent
44
-
-
Auditorium- Supply Installation Testing & Commissioning of Identification name plate round 79MMundergone through 7Tank chemical treatement to keep them rust free and duly powder coated in black matt texture finish Recommended Make : Canara Lighting / ARRI / Desisti/Equivalent
44
-
-
Auditorium- Supply Installation Testing & Commissioning of MS suspender consisting of fish plate of 150X150X6mm undergone through 7Tank chemical treatement to keep them rust free and with requisite anchor fastner(Customised) duly powder coated in black matt texture finish & stud with 12mm threaded rod to keep the Bar rigidly held With SWL of 200kg. Recommended Make : Customised / Canara Lighting / Stage technologies/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Pipe Class B dual barrel 40NB powder coated with Matt black finish, 2.2mm wall thickness. P.S. Pipe should have under gone 7 tanks chemical treatment process and rusto cleaned. Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Wing lader, made using 40NB dual barrel undergone through 7 Tank chemical treatement to keep them rust free and duly powder coated in black matt texture finish Size of 1800mm x 600mm.Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
4
-
-
Auditorium- Supply Installation Testing & Commissioning of Fixed Front of house Light bar, length 14 Mtrs made using 40NB dual barrel undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish and provided with suitable suspender and clamps..Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS, Wing Dual frame construction,made out of 25X25mm MS square pipe with 2mm in thickness powder coated of size H 7.5 Mtr x W 2 Mtr, provided with 1.5meter wing track of 48X84mm with gridmount brackets made of 40X50X40mm C track Pivotable 4wheeled suspension trolley Adjustable floor locking screw jacks with rubber grips Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp Extruded track Aluminium I Profile to be laid through out the dept of the stage..Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of Main Valance fixing arrangement using 40NB made up of SAIL/Jindal Recommended Make 2mm thick, 21 Mtr in length MS pipe, undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with matt black texture finish with mounting brackets..Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Grand Tab track system 21 Mtr long, centre parting with overlap of 0.9mtr provided with,Heavy duty extruded aluminium I track of 48x84mm, powder coated Track mounting brackets constructed of C track of dimension 40X50X40mm Electromechanical drive unit with 3PH INDUCTION MOTOR, 1.1KW, 3000RPM, 90B5 FLANGE MOUNT with GI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center Curtain holding Nylon wheel trollies consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track.Nylon moulded 6201 Ball bearing Diverter pulley with with 90mm for outer diameter, 72mm diameter at groove base, 19mm pulley thickness & MS yellow passivated Routing pulleys with 165mm for outer diameter, 150mm diameter at groove base with 12mm pulley thickness..Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Rear curtain track system 18 mtr long, centre parting with overlap of 0.9mtr provided with,Heavy duty extruded aluminium I track of 40X70mm, powder coated Track mounting brackets constructed of C track of dimension 40X50X40mm Manual Operating GI wire ropes of 3mm in diameter constructed with 7 bundles of 7 strands with steel core at center Curtain holding trollies consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of 200mm throughout the track.MS yellow passivated Diverter pulley with with 100mm for outer diameter, 81.5mm diameter at groove base, 13mm pulley thickness & MS yellow passivated Routing pulleys with 165mm for outer diameter, 145mm diameter at groove base with 12mm pulley thickness..Recommended Make : Waagner Biro / Stage technologies / Canara Lighting/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Power junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 4 way 10A IEC Socket of below specifications:- Fixing : Snap fit /15 (1.5mm) , Terminations : /28 (2.8mm solder), Total Max Rating : 10A, 250V a.c, Operating Temp : –20˚C to +70˚C , Mouldings : Nylon, Flammability Rating UL94V-0.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
15
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Power junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 1 way 16A CEE Socket of below specifications:- Amperage : 16A Poles : 3p (2P+PE) , Earth 'Clock' Position : 6h Voltage : 200 up to 250V ,Frequency : 50 and 60Hz , Color code : blue RAL 5015 , Connection Design : Screw Terminal ,Max Conductor : 2,5 mm² , Material of Enclosure : Polyamide , Contact Carrier : contact carrier made of Polyamide, the contacts are brass.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
8
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Power junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 1 way 32A CEE Socket of below specifications:- Amperage : 32A , Poles : 3p (2P+PE), Earth 'Clock' Position : 6h, Voltage : 200 up to 250V, Frequency : 50 and 60Hz ,Color code : blue RAL 5015, Connection Design : Screw Terminal , Max Conductor : 6.0 mm², Material of Enclosure : Polyamide , Contact Carrier : contact carrier made of Polyamide, the contacts are brass.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
15
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Signal junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 5 pin XLR DMX out connector of below specifications:- Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination ,Optional connection to easily join pin 1 to chassis ground.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
14
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Signal junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish finish 5 pin XLR DMX in connector of below specifications:- Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination ,Optional connection to easily join pin 1 to chassis ground.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Auxilary fabricated marshalling boxes made up of 20SWG CRCA sheet undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish for all the light bar with required no of ivory connectors.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS fabricated power marshalling box made up of 20SWG CRCA sheet undergone through undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish ivory connect conectwell Recommended Make and FC-11 naylon gland,Brass galnd suitable for power cable with proper earthing connecter .Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS Fabricated made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish power junction box (PJB) to terminate the Motorized section power connections.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Well designed and engineered Wall mount chocolate brown epoxy polyster coated type power distribution centre panel with necessary metering like voltmeter ammeter, Selector switch,indicators, outgoing feeders and 200 Amps main incomer L&T Recommended Make and emergency trip arrangement with shunt Release (PDCP-200) and 30 way MCB Panel wall mount internally wired to control individual Direct light points with suitable MCBs with proper erathing and suitable brass glands for outing power cables.Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Well designed and engineered Wall mount 1 feeder motor control centre panel & Remote control panel with, necessary meterings and contactors and relays to control the motors system for curtains.(MCCP/RCP -1).Recommended Make : Canara Lighting / ABB / SCHNEIDER/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS sheet metal fabricated emergency push button station undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with Matt black texture finish for emergency trip.
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS sheet metal fabricated power junction box duly powder coated and fitted with 2 10amps 3 pin IEC socket,ON/OFF switch and necessary glands to power splitters and console undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with Matt black texture finish for dimmable points along with the FC7 glands.Recommended Make : Customised / Canara Lighting/Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of Internal earthing copper bare conductor network related to work coming under our scope.
1
-
-
Auditorium- Supply Installation Testing & Commissioning of hardwares such as clamps, connectors, glands, lugs, ferruels, welding rods etc.
1
-
-
Auditorium- Supply Installation Testing & Commissioning of MS perforated trays with tray lid treated Size 40 x 75 x 40mm & Size 40 x 150 x 40mm with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with matt black texture finish paint along with clamping arrangement as required.Recommended Make : Customised / Canara Lighting/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Digital Lighting Console with 1024 DMX channels 1024 Channels, 96 Fixtures, Time control of scenes: Fade in/out, LTP slope, Channels for each fixture 40 primary + 40 fine tune , LCD display with back light 60 Scenes/Playbacks, 10 Scenes to run simultaneoulsy, 600 Scene step, Shape generato: Shapes of Dimmer, Pan/Tilt, RGB, CMY, Color, Gobo, Iris and Focus Master slider - Global, playback, fixture, USB Memory - FAT32 supported. Recommended Make : Liteputer / Avolite / Zero88/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Grid mount photo isolator DMX Amplifier unit 1 DMX input and 8 isolated output with following specifications: Power Supply: 90-240V AC, 45-63Hz, Control: DMX 512 protocol, Control Signal input: 5 pin XLR female, Size: 482 x 44 x 128mm , Weight: 2Kg.with splitter bracket. Recommended Make : Liteputer / Avolite / Zero88/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Grid mount dimmer pack with 16A CE output socket, 5 pin XLR socket for DMX control.FEATURES: Maximum 10A per channel, total 30A, DMX 512 signal, 2 sets of signal input/output, 3 pin XLR connector and RJ11 phone jack, LED display, Automatic warm up function protects loads and extend the life of fixtures, Auto frequency tracking, ‘C3’ dimming curve, DMX start channel address setting, Channel dimming test, 256 steps dimming resolution, Equipped with clamp for truss hanging or desktop operation, SPECIFICATION: Power : AC 100-120V, AC 200-240V, 45-63Hz, 2 input, Output : Max. 10A per channel, total 30A, Signal input / output : DMX 512 / 1990, Signal connector : XLR 3pin, 6P4C, RJ12 phone jack, Installation : Truss hanging or desktop operation. Fuse : 10A , Weight : 3.2kg. Recommended Make : Liteputer / Avolite / Zero88/Equivalent
10
-
-
Auditorium- Supply Installation Testing & Commissioning of 750W HPL 230V lamps G9.5 Base.Recommended Make : Philips / Osram / GE/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of 1000 W 240V R7s base 187mm + 2mm long tungsten lenier Halogen lamp.Recommended Make : Philips / Osram / GE/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of 1000W 230V single ended halogen lamp CP24 / CP70 Base Gx9.5.Recommended Make : Philips / Osram / GE/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of 1000W 230V Par-64 narrow / medium / wide lamps with base Gx16d for 1kW Halogen parcans. Recommended Make : Philips / Osram / GE/Equivalent
16
-
-
Auditorium- Supply Installation Testing & Commissioning of 5 pin XLR male / female connectors.Recommended Make : Neutrik / CL / Amphenol /Equivalent
20
-
-
Auditorium- Supply Installation Testing & Commissioning of 5 Pin XLR Termination plug.Recommended Make : Neutrik / CL / Amphenol /Equivalent
15
-
-
Auditorium- Supply Installation Testing & Commissioning of Valcro Tape (White if available)
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Assorted colour gel filter roll size 4ft x 25ft.
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Fire retardant velvette fabric with lining 100% gathering for main Valance with approved color duly stitched.Size : 21 Mtr x 1.5 Mtr.Recommended Make : Rayan / Ompile / Raymonds/Equivalent
1
-
-
Auditorium- Supply Installation Testing & Commissioning of Fire retardant velvette fabric with lining, 100%(Double) gathering for Main curtain with approved color duly stitched and with eyelets.
Size : 11 Mtr x 8 Mtr.Recommended Make : Rayan / Ompile / Raymonds/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Fire retardant Cotton fabric with lining, 50% gathering for Rear curtain with approved color duly stitched and with eyelets.Size : 10 Mtr x 8 Mtr.Recommended Make : Rayan / Ompile / Raymonds/Equivalent
2
-
-
Auditorium- Supply Installation Testing & Commissioning of Fire retardant Cotton fabric with lining, 50% gathering for frill with approved color duly stitched and with eyelets.Size : 14 Mtr x 1.5 Mtr.Recommended Make : Rayan / Ompile / Raymonds/Equivalent
3
-
-
Auditorium- Supply Installation Testing & Commissioning of Fire retardant cotton fabric 0% gathering for wings as per the approved patern and colour, not less than 250 GSM, duly stitched along with Navar strip 50mm wide . Size: 7.5 Mtr x 4.2 Mtr. Recommended Make : Mayur / Ompile / Raymonds/Equivalent
6
-
-
Auditorium- Supply Installation Testing & Commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx2.5 sq mm.Recommended Make : Walna / SBEE / Polycab/Equivalent
600
-
-
Auditorium- Supply Installation Testing & Commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 12cx2.5 sq mm.Recommended Make : Walna / SBEE / Polycab/Equivalent
200
-
-
Auditorium- Supply Installation Testing & Commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx4 sq mm.Recommended Make : Walna / SBEE / Polycab/Equivalent
300
-
-
Auditorium- Supply Installation Testing & Commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 12cx4 sq mm.Recommended Make : Walna / SBEE / Polycab/Equivalent
200
-
-
Auditorium- Supply Installation Testing & Commissioning of PVC Copper armoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 4cx4 sq mm.Recommended Make : Walna / SBEE / Polycab/Equivalent
50
-
-
Auditorium- Supply Installation Testing & Commissioning of FRLS PVC copper multistrand flexible cable 7 core x 1.5 sq.mm.Recommended Make : Walna / SBEE / Polycab/Equivalent
60
-
-
Auditorium- Supply Installation Testing & Commissioning of DMX signal cable for DMX network.Recommended Make : Falcon / Beldon / Polycab/Equivalent
450
-
-
Auditorium- Supply Installation Testing & Commissioning of 16A CEE Cable mount Plug.Recommended Make : Customised / Canara Lighting/Equivalent
8
-
-
Auditorium- Supply Installation Testing & Commissioning of CEE to CEE 3m Y chord .Recommended Make : Customised / Canara Lighting/Equivalent
5
-
-
Auditorium- Supply Installation Testing & Commissioning of CEE to CEE 5m Y chord .Recommended Make : Customised / Canara Lighting/Equivalent
3
-
-
Auditorium-Audio, Video , Lighting, Control system Programming & Calibration Charges
1
-
-
AV Theater- Supply Installation Testing & Commissioning of 3-Way Loudspeaker with following Specification Passive or Bi-amp, Dual 15" LF D river ,6.5" HF Driver,Nominal Coverage 90° horizontal x 40° vertical,Frequency Response 38 Hz- 20 kHz,Frequency Range 32 Hz- 20 kHz,Impedance LF @ 4 ohms MHF @8 ohms, Sensitivity 102dB, Maximum Input Power 500watts @ LF & 80Watts @MHF or better. Recommended Make : Christie /QSC / Alcons/Equivalent
3
-
-
AV Theater- Supply Installation Testing & Commissioning of Cinema Subwoofer with following Specification 18" Driver,Frequency Range 29 Hz to 170 Hz,Rated Noise Power 600 W,Sensitivity 98 dB,Maximum Peak SPL 131 dB,Rated Impedance 8Ω or better Recommended Make : Christie /QSC / Alcons/Equivalent
2
-
-
AV Theater- Supply Installation Testing & Commissioning of Cinema Surround Speaker with Following Specification Rated Power 200Watts,Frequency Range 52 Hz to 20 kHz,Rated Coverage Angle 90° axisymmetric,Maximum peak 123dB SPL ,Continuous 117 dB,Rated Impedance 8 ohms,Sensitivity 94 dB or betterRecommended Make : Christie /QSC / Alcons/Equivalent
12
-
-
AV Theater- Supply Installation Testing & Commissioning of Mounting Bracket for surround Speaker or better Recommended Make : Christie /QSC / Alcons/Equivalent
8
-
-
AV Theater- Supply Installation Testing & Commissioning of Mounting Bracket for surround Speaker or better Recommended Make : Christie /QSC / Alcons/Equivalent
4
-
-
AV Theater- Supply Installation Testing & Commissioning of CinemaPower amplifier with Following Specification 4 Channel Amplifier Rated Power 170 W@8Ω, per channel , 250 W @4Ω,Bridged Mono Mode 340W @ 16Ω,500 W @8Ω,,Signal to Noise -105dB ,Frequency Response 20 Hz–20 kHz, ± 0.2 dB 8 Hz–50 kHz, + 0, -3 dB ,Damping Factor 500 Input Impedance 10K Ohm or better Recommended Make : Christie /QSC / Alcons/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of Cinema Power Amplifier with following specification 2 Channel Amplifier 300 W@8Ω, ,500 W 4Ω, ,BRIDGED MONO MODE 600 W @16Ω, ,1100 W@8Ω, 2,1600 W@4Ω, ,Signal to Noise 20 Hz–20 kHz 107 dB ,Frequency Response 20 Hz–20 kHz, ± 0.2 dB 8 Hz–50 kHz, + 0/-3 dB ,Damping Factor 1 kHz and below , 500,Input Impedance ,10 kΩ unbalanced, or better Recommended Make : Christie /QSC / Alcons/Equivalent
3
-
-
AV Theater- Supply Installation Testing & Commissioning of Cinema Power Amplifier with Following Specification 2 Channel Amplifier 425 W@8Ω,,700 W@4Ω,, BRIDGED MONO MODE 850 W@16Ω, 1500 W@8Ω, ,1600 W @4Ω, Signal to Noise 107 dB ,Frequency Response 20 Hz–20 kHz, ± 0.2 dB 8 Hz–50 kHz, + 0/-3 dB ,Damping Factor 1 kHz and below Greater than 500 ,Input Impedance 10 kΩ unbalanced, 20 kΩ balanced or better Recommended Make : Christie /QSC / Alcons/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of Digital Processor/Monitor/Crossover Speaker with following Specification 2"x 3.5" full-range ,Frequency response 20 Hz to 20 kHz,Connector DB25F - 8 channel ,Input stage type Active balanced input Input impedance 20k Ohms ,it can be controlled via RS-232 or better Recommended Make : Christie /QSC / Alcons/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of DLP Projector with following Specification Single Chip DLP Projector , 9000 ANSI , WQXGA Resolutions 2560x1600 , Up to 4K UHD @ 60Hz,24/7 Operation,Contrast Ratio 1200:1, Aspect Ratio 16:10,Motorized zoom, focus, vertical and horizontal shift,Orientation 360° rotation,Connectivity Inputs HD SDI, 2x DP 1.2, 2x dual link DVI-D, HDBaseT, HDMI 2.0*, RJ 45 Ethernet, RS232 in, 2x USB, ,Control IR, RS232, RJ45 with Appropriate long throw lens or better. Recommended Make : NEC /Barco / Digital Projection/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of floor stand for projector at projection room Recommended Make : Custom/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of 432" Screen , Aspect Ratio 2.39:1 ,Supports 4k Digital Perforated Screen, Gain 1.4 or better Recommended Make : Harkness/Galalite/Draper/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of Frame Structure for 432 " Screen Recommended Make : Custom/Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of 15 Meter Fiber optic supports 4:4:4 @ 60Hz HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand /Logic/Wyerstorm /Equivalent
1
-
-
AV Theater- Supply Installation Testing & Commissioning of 2.5 Sq.mm Speaker Cable in meter or better Recommended Make : Belden /KLotz/Chetan/Equivalent
100
-
-
AV Theater- Supply Installation Testing & Commissioning of 4 Sq Mm Speaker Cables for Subwoofers in meter or better Belden /KLotz/Chetan/Equivalent
200
-
-
AV Theater- Supply Installation Testing & Commissioning of Assorted Cable , Connectors & Conduiting Recommended Make : Custom/Equivalent
1
-
-
AV Theater- Audio & Video Programming & Calibration Charges Recommended Make : Custom/Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Stage Monitor with following Specification 2000W Class D Amplifier with inbuild DSP, 12 inch LF Driver& 1.4" HF Driver ,Frequency Response 50 Hz - 20 kHz,Frequency Range 45 Hz - 20 kHz, Maximum SPL 132dB, Axisymetric Coverage angle 75 Degree Or better Recommended Make : Meyer Sound /QSC / K- Array /Equivalent
3
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Active Subwoofer with following Specification Single 18" Rated power 2000Watts @ peak /1000Watts @ continous Frequency Response 40 Hz to 112 Hz,Frequency Range 37 Hz to 129 Hz,Maximum SPL 135 dB or better Recommended Make : Meyer Sound /QSC / K- Array /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Active loudspeaker with Following Specification system with 12-inch woofer ,1.0-inch compression driver , Build In DSP,75 degree conical waveguide, Frequency Response 56 Hz - 20 kHz , Frequency Range 50 Hz – 20 kHz, Nominal Coverage 90° , Peak SPL 130dBAxisymetric dual angle pole socket; For use as main or stage monitor Or better Recommended Make : Meyer Sound /QSC / K- Array /Equivalent
4
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Powder coated steel yoke for mounting the Stage Monitor Speaker vertically or Horizontally to structures. or better Recommended Make : Meyer Sound /QSC / K- Array /Equivalent
3
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Digital Signal Processing with following Specification 24 local I/O channels, Dedicated 8 Input & 8 output , Expandable upto 128x128 network I/O channels, telephone POTS, General Purpose Input 16 output 16 , 16 AEC channels, LAN Port x2, USB B type port ,RS232 or better Recommended Make : Meyer Sound /QSC / K- Array /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 16 Channel Mixer with 16 Mic/line input ,3 Band EQ, 4 Stereo band with 2 Band Equalizer or better Recommended Make : Allen Heath / Yamaha / Sound Craft/Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Wireless Handheld Mic with single channel wireless receiver & Transmitter or better Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
4
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Wireless Lapel Mic with Frequency Response: 60 Hz – 12 kHz,Sound Pressure: 139 dB,Transducer Type: Condenser,Polar Pattern: Cardioid, Transmitter Operating Range (up to): 100 m nInput impedance: 1000 kΩ or better Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Headworn Mic ,bodypack Transmitter with Receiver or better Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of WiredHandheld Mic withType Dynamic ,Frequency Response 50 to 15.000 Hz,Polar Pattern Unidirectional (cardioid) or better Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
4
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Fixed PTZ Camera with following Specification 1/2.8" progressive Scan CMOS sensor, 2.14 Megapixel ,30X optical Zoom, Supporting Video Format 1080p 59.94/50/29.97/25,1080i 59.94/50,720p 59.94/50,480i, 576i (on CVBS), White Balance Indoor/Outdoor/Fluorescent/AWB/MWB, Auto & Manual Focus,Pan 270 Degree, Tilt +90 Degree -20 Degree, Presets 50, Focul Length f=4.3mm wide to 129mm TELE ,Connectivity 3G-SDIx1, HDMIx1,CVBSx1 , Protocol VISCA DVIP or better Recommended Make : Datavideo/AJA/Space /Equivalent
3
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Integration of 6-CH HD Video Switcher, H.264 Streaming Encoder and Recorder , 17" Multiviewer HD monitor or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Joystick Control Unit with following Specification total 4 preset position for each camera, Control Protocol Sony VISCA or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Balanced/Unbalanced input Audio Delay Box for up to 700ms (17 frames) audio delay calibration, Volume attenuating 0 ~ 60dBConnectivity Audio Input XLRx3,RCAx2, Audio Output XLRx2, RCAx2 or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Blackbox Theater- Blackbox Theater- Supply Installation Testing & Commissioning of Multiformat Converterwith following Specification VGA to3G/HD/SD SDI Converter Connectivity VGAx1,HDMIx1,3G/HD/SD SDI as input & HDMIx1,3G/HD/SD SDI x2, Supported Video Format 1080p , (23.98/24/25/29.97/30/50/59.94/60Hz), Equalizer & reclock the signal or better Recommended Make : Datavideo/AJA/Space /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of encoder with following Specification HDMI signals up to 1080p60 to stream or record the content to a network drive, Built–in Scaling and Frame Rate Control, Standard Ethernet Network Operation — 10/100/1000Mb, Input: HDMIx1, AudioInx1, Ethernetx1, RS232x1, Output: HDMIx1, VGAx1, AudioOutx1 or better Recommended Make : Kramer/AJA/Space /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Network Storage Device with following Specification 2 Bay, Max. storage capacity upto 24TB, Processor: Quad core 1.4GHz High Performance ARM Cortex A15, Memory: 2GB RAM or better Recommended Make : Linksys/DLink/Netgear /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 4TB Hard disk or better Recommended Make : Toshiba /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 15 U Rack with Accessories or better Recommended Make : Custom /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 1.8 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 2.5 Sq.mm Speaker Cable for Line array Speakers in meter or better Recommended Make : Belden /KLotz/Chetan /Equivalent
200
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 4 Sq Mm Speaker Cables for Subwoofers in meter or better Recommended Make : Belden /KLotz/Chetan /Equivalent
100
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 2 Core Microphone cable in meter or better Recommended Make : Belden /KLotz/Chetan /Equivalent
100
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Serial Digital Interface Camera Cable in meter or better Recommended Make : Kramer/ NT /Belden /Equivalent
250
-
-
Blackbox Theater- Blackbox Theater- Supply Installation Testing & Commissioning of 4 Channel Junction Box Recommended Make : Custom /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Assorted Cable , Connectors & Conduiting Recommended Make : Custom /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of High quality LED PAR RGBW Light used as a Effect Light, Spot Light and Strobe
Light etc., with below specifications: Lamp: 54 X 3W RGBW LED (12R+18G+18B+6W),Power consumpsion:162W ,Power supply: 100-230V AC, 50/60Hz , Power cable: 3 core 1.5 sq. mm. copper PVC insulated, Channels: 8 Channel DMX-512, Beam angle: 25° ,Control mode: DMX, and Manual, LUX @ 2m: 11,000, Function: strobe, dimming, sound active,Dimming: 0 - 100%, Housing: Diecast aluminium with black epoxey polyster powder coated, Power and DMX: Loop in and loop out , Dimension: W 220 x L 240 x H 335mm, Weight: 2.9 Kg , Certification: CE Recommended Make : Desisti / ARRI / Canara lighting /Equivalent
8
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of High quality LED PAR light used as a Key light, Back light, Fill light, with dimming, spot/flood versions for creating many effects for various applications with below specifications:Lamp: 54 X 3W 3200K LED, Power consumpsion: 162W, Power supply: 100-230V AC, 50/60Hz, Power cable: 3 core 1.5 sq. mm. copper PVC insulated, Channels: 8 Channel DMX-512, Beam angle: 25° ,Control mode: DMX, and Manual, LUX @ 2m: 12,300, Function: strobe, dimming, sound active, Dimming: 0 - 100%,Housing: Diecast aluminium with black epoxey polyster powder coated, Power and DMX: Loop in and loop out, Dimension: W 220 x L 240 x H 335mm,Weight: 2.9 Kg, Certification: CE Recommended Make : Desisti / ARRI / Canara lighting /Equivalent
10
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of High quality Canara 120W LED Profile Spot Light used as a Spot Light and high-contrast gobo projection Light with below specifications : Lamp Power : LED, 120W,Power Supply : AC 110-230V, 50Hz, Focus : Manual Focus, Beam Angle : 19°, Control : DMX, Autorun and Master/Slave , DMX Control protocol: DMX 512, CRI : 90, LUX @ 2m: 17,350, Dimming : 100 - 0% dimming, Control system : DMX,Auto run and master/slave, Shutter: Beam shaping shutter or plastic gobo projection assembly, Protection Rating : IP20, Dimension: W 300 x L 700 x H 310mm, Net Weight : 7.5 Kgs Certification: CE Recommended Make : Desisti / ARRI / Canara lighting /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of High quality COB LED 2 x 100W blinder matrix Light is used in Entertainment applications, Night club, Fashion shows, Film, Band performances, Discotheque, Stage performance , TV studio and large-scale show etc fixture with advanced COB LED technology with below specifications:- Power Consumption: 200W, Power Supply: 100-230V AC, 50-60Hz Light Color: Single color warm white (3200K), LEDs Qty : 2 pieces, Channel: 2/5 channel Lifetime: Over 50,000 hours, Beam Angle: 30 degree, Control mode: DMX512,Master/Slave, Auto Run, Sound active,Dimmer: 0~100% linearly adjustable LUX: 3960 LUX @ 2m, IP Grade: IP20, Dimension: W 128 x L 378 x H 218 mm Net Weight: 3.75 Kgs, Certification: CE Recommended Make : Selecon / ETC / Canara lighting /Equivalent
4
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 100W LED PARCAN Aluminum housing with black powder coated finish with below specifications: Lamp power - 100W,Power supply - 100-240 AC, 50/60 Hz Channels: 2 channel DMX 512, Control: Manual, DMX, Color Temperature: 3000K CRI 90 ,Function: Dimming, Strobe, Dimming: 0-100%,Beam Angle - 15/20° Protection rating - IP20,Dimension - 420 x 280 x 452mm, Weight – 4.5 Kgs Recommended Make : Selecon / ETC / Canara lighting /Equivalent
6
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Diecast aluminum "C" clamp with safety locking chain, duly powder coated in black matt texture finish and technical specifications as below. Lock - MS threaded Galvanized lock key, Plastic Glass filled nylon moulded M6 key. Receptacle - 28mm standard TV spigot, Safety - MS Galvanized chain with pin. Finish - Pretreated and black epoxy polyester powder coated, Self weight - 0.54Kg Safe working load – 150Kg. Recommended Make : Canara Lighting / ARRI / Desisti /Equivalent
30
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Safety bond with lock clip to be fixed around the grid to avoid fall of the material in case if the "C" clamp is not locked properly . SWL 100Kgs Recommended Make : Canara Lighting / ARRI / Desisti /Equivalent
30
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Identification name plate round 79MMundergone through 7Tank chemical treatement to keep them rust free and duly powder coated in black matt texture finish. Recommended Make : Canara Lighting / ARRI / Desisti /Equivalent
30
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS suspender consisting of fish plate of 150X150X6mm undergone through 7Tank chemical treatement to keep them rust free and with requisite anchor fastner(Customised) duly powder coated in black matt texture finish & stud with 12mm threaded rod to keep the Bar rigidly held With SWL of 200kg. Recommended Make : Customised / Canara Lighting /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS Pipe Class B dual barrel 40NB powder coated with Matt black finish, 2.2mm wall thickness. P.S. Pipe should have under gone 7 tanks chemical treatment process and rusto cleaned. Recommended Make : Stage lighting / Stage technologies / Canara Lighting /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Fixed Front of house Light bar,length 5mtrs made using 40NB dual barrel undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish and provided with suitable suspender and clamps. Stage lighting / Stage technologies / Canara Lighting /Equivalent
3
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS Power junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 4 way 10A IEC Socket of below specifications: Fixing : Snap fit /15 (1.5mm), Terminations : /28 (2.8mm solder) ,Total Max Rating : 10A, 250V a.c, Operating Temp : –20˚C to +70˚C, Mouldings : Nylon, Flammability Rating UL94V-0. Recommended Make : Canara Lighting / ABB / SCHNEIDER /Equivalent
18
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS Signal junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish 5 pin XLR DMX out connector of below specifications: Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination , Optional connection to easily join pin 1 to chassis ground. Recommended Make : Canara Lighting / ABB / SCHNEIDER /Equivalent
6
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS Signal junction box made up of 22SWG CRCA sheet of jindal Recommended Make undergone through 7 tank process with various chemical treatment to keep them rust free, duly powder coated with Matt black texture finish finish 5 pin XLR DMX in connector of below specifications: Extra high temperature resistant insulator material, All metal housing offers best overall RF protection & electromagnetic shielding, New duplex ground contact for excellent contact integrity between chassis and cable connector, Larger solder contacts for easier termination, Optional connection to easily join pin 1 to chassis ground. Recommended Make : Canara Lighting / ABB / SCHNEIDER /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 18 way direct lighting distribution board with suitable SP Mcb's and TPN incomer for the junction boxes fixed on the top of the grid including wiring and busbar connection with proper earthing. Recommended Make : Canara Lighting / ABB / SCHNEIDER /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS sheet metal fabricated power junction box duly powder coated and fitted with 2 10amps 3 pin IEC socket,ON/OFF switch and necessary glands to power splitters and console undergone through 7 tank process with various chemical treatment to keep them rust free duly powder coated with Matt black texture finish for dimmable points along with the FC7 glands. Recommended Make : Canara Lighting / ABB / SCHNEIDER /Equivalent
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Internal earthing copper bare conductor network related to work coming under our scope.
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of hardwares such as clamps, connectors, glands, lugs, ferruels, welding rods etc.
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of MS perforated trays with tray lid treated Size 40 x 75 x 40mm & Size 40 x 150 x 40mm with 7 tank process with various chemical treatment to keep them rust free, duly powder coated with matt black texture finish paint along with clamping arrangement . Recommended Make : Customised / Canara Lighting /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Grid mount photo isolator DMX Amplifier unit 1 DMX input and 8 isolated output with following specifications: Power Supply: 90-240V AC, 45-63Hz. Control: DMX 512 protocol, Control Signal input: 5 pin XLR female, Size: 482 x 44 x 128mm , Weight: 2Kg.with splitter bracket. Recommended Make : Liteputer / ADB / Zero88/Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Portable digital lighting console having Dual signal output DMX-512 channels programs console, 1000 scenes memories etc with following specifications: Dual signal output DMX-512 channels programs console, 1000 scenes memories. 12 hot keys for scene recall, 2 cross fade for scene change, Save 512 groups of chasers and each chaser contains 256 steps, Power Supply : DC12V/1A, Protocol : DMX-512. Channels: 512 DMX connection: XLR 5-pin, Installation: 19" 4U Standard rack, Weight: 2.3Kg, Dimension: 482(W)x55(H)x176(D)mm. Recommended Make : Avolites / liteputer / Zero 88 /Equivalent
1
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 5 pin XLR male / female connectors. Recommended Make : Neutrik / CL / Amphenol /Equivalent
10
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of 5 Pin XLR Termination plug. Recommended Make : Neutrik / CL / Amphenol /Equivalent
6
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of Valcro Tape (White if available)
2
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of PVC Copper unarmoured flexible FRLS insulated multicore cable 1100V grade confirming to IS694 size 3cx1.5 sq mm. Recommended Make : Walna / SBEE / Polycab /Equivalent
800
-
-
Blackbox Theater- Supply Installation Testing & Commissioning of DMX signal cable for DMX network. Recommended Make : Falcon / Beldon / Polycab /Equivalent
180
-
-
Blackbox Theater- Programming & Calibration Charges Recommended Make : Custom /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 2-way 6.5" Driver Wall mount speaker with following Specification 30Watts rated Power ,Frequency range 60 to 20KHz, Sensitivity 86dB, Max peak Spl: 107 dB, impedence 8 Ω, 70/100V Transformer Tapping with 8 Ohm Bypass or better Recommended Make : BOSE /QSC / L -Acoustics/Equivalent
6
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Amplifier with following Specification Class D Amplifier, 200 watts per channel into 4 and 8 ohms ,Bridged Mode 400Watts @ 8 &4Ohm, 350Watts @70V/100V , Signal to Noise ratio 100dB ,Frequency Response (20 Hz - 20 kHz) or better Recommended Make : BOSE /QSC / L -Acoustics/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 10-Channel Live + USB Recording Mixer with 4mic/line input &2 Stereo Inputs ,48V Phantom Power for condenser mics,3 band EQ or better Recommended Make : Digico /Allen & heath/ Midas/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Wireless Handheld Mic with single channel wireless receiver & Transmitter or better Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Wireless Lapel Mic with Frequency Response: 60 Hz – 12 kHz,Sound Pressure: 139 dB,Transducer Type: Condenser,Polar Pattern: Cardioid, Transmitter Operating Range Maximum 100 m ,Input impedance: 1000 kΩ or better Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Gooseneck Mic with Type Electret Condenser,Polar Pattern Cardioid,Frequency Response 70–16,000 Hz or betterRecommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of DLP Projector with following Specification Single Chip DLP Projector , 4750ANSI , WXGA Resolutions 1280*800 , , Contrast Ratio 1800:1, Aspect Ratio 16:10,Optical lens shift Vertical: -30% to +110% / horizontal: -10% to +10%, 3D cabable, Connectivity Inputs HDMI; DVI-D; DisplayPort; 2 x VGA in; VGA out; RGBHV; YUV; S-video; video ; RJ-45 1;3D Sync out; Audio out,Control IR, RS232, RJ45 or better Recommended Make : NEC /Barco / Digital Projection/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Projector Mounting Kit with Height Adjustment or better Recommended Make : Custom/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 123 inch Fiber Glass MW Tubular Motor screen with RF remote or better Recommended Make : Grand Logic/Draper/Da-lite/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Passive Wall Plate with VGA+A , HDMI port, pigtail & Backbox or better Recommended Make : Extron/Logic/Kramer/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning off 2.4 GHz Multifunction wireless presenter with Trackball mouse and Pointeror better Recommended Make : Logic/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 15U Rack with Accessories or better Recommended Make : Custom/Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 3 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 10 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 3 Meter VGA+A Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of 10 Meter HDMI Male To Male Cable or better Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
Seminar Hall- Supply Installation Testing & Commissioning of2.5 Sq.mm Speaker Cable for Line array Speakers in meter or better.Recommended Make : Belden/KLotz/Chetan/Equivalent
100
-
-
Seminar Hall- Supply Installation Testing & Commissioning of2 Core Microphone cable in meter or better.Recommended Make : Belden/KLotz/Chetan/Equivalent
50
-
-
Seminar Hall- Supply Installation Testing & Commissioning of Assorted Cable , Connectors & Conduiting.Recommended Make : Custom /Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 3-Way Loudspeaker with following Specification Passive or Bi-amp, Dual 15" LF Driver ,6.5" HF Driver,Nominal Coverage 90° horizontal x 40° vertical,Frequency Response 38 Hz- 20 kHz,Frequency Range32 Hz- 20 kHz,Impedance LF @ 4 ohms MHF @8 ohms, Sensitivity 102dB, Maximum Input Power 500watts @ LF & 80Watts @MHF or better.Recommended Make :Christie /QSC / Alcons/Equivalent
3
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Cinema Subwoofer with following Specification 18" Driver,Frequency Range 29 Hz to 170 Hz,Rated Noise Power 600 W,Sensitivity 98 dB,Maximum Peak SPL 131 dB,Rated Impedance 8Ω or better.Recommended Make :Christie /QSC / Alcons/Equivalent
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Surround Loudspeaker with Following Specification 8" long throw low frequency transducer and 1" soft dome tweeter, Frequency Range: 54 Hz to 20 kHz, Nominal Coverage: 130° horizontal x 110° vertical, Maximum Rated SPL: 118 dB(Peak) and 112 dB(Continuous), Sensitivity 1 watt/1 meter: 91 dB, Crossover Frequency: 1.7 kHz, Or better.Recommended Make :Christie /QSC / Alcons/Equivalent
6
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Brackets for Main Surround Speaker or better.Recommended Make :Christie /QSC / Alcons/Equivalent
6
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Cinema Power amplifier with Following Specification 4 Channel Amplifier Rated Power 170 W@8Ω, per channel , 250 W @4Ω,Bridged Mono Mode 340W @ 16Ω,500 W @8Ω,,Signal to Noise -105dB ,Frequency Response 20 Hz–20 kHz, ± 0.2 dB 8 Hz–50 kHz, + 0, -3 dB ,Damping Factor 500 Input Impedance 10K Ohm or better.Recommended Make :Christie /QSC / Alcons/Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Cinema Amplifier with following Specification 2-Channel Power Amplifier with 200 W at 8Ω and 325 W at 4Ω. In Bridged mono mode: 400 W at 16Ω, 700W at 8Ω and 1200W at 4Ω, Signal to Noise: 106 dB, Input Sensitivity: 1.0 V rms at 8 ohms and 0.9 V rms at 4 ohms. Frequency Response: 20 Hz–20 kHz. or better .Recommended Make :Christie /QSC / Alcons/Equivalent
3
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Cinema Power Amplifier with following specification 2 Channel Amplifier 300 W@8Ω, ,500 W 4Ω, ,BRIDGED MONO MODE 600 W @16Ω, ,1100 W@8Ω, 2,1600 W@4Ω, ,Signal to Noise 20 Hz–20 kHz 107 dB ,Frequency Response 20 Hz–20 kHz, ± 0.2 dB 8 Hz–50 kHz, + 0/-3 dB ,Damping Factor 1 kHz and below , 500,Input Impedance ,10 kΩ unbalanced, or better.Recommended Make :Christie /QSC / Alcons/Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Processor with following Specification Digital Processor with Ten digital inputs for 5.1 and 7.1 soundtracks and HI/VI, Dolby® Digital Plus® and DTS®-HD, Network control and monitoring via SNMP, Serial automation control via RS-232, Analog Inputs for film processors, non-sync and Mic/Line, Compatible with all existing DCA amplifiers, Frequency response: 20 Hz to 20 kHz, Inputs/outputs: Main Analog Input, Mic/Line Input (XLR), Stereo Line Inputs, DataPort Outputs (HD15), HI/VI Outputs, Monitor Headphone Output, RJ45 and Mono RCA or better.Recommended Make :Christie /QSC / Alcons/Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of DLP Projector with following Specification Single Chip DLP Projector , 7000 ANSI , WQXGA Resolutions 2560x1600 , Up to 4K UHD @ 60Hz,24/7 Operation, 3D Support, Contrast Ratio 1200:1, Aspect Ratio 16:10,Motorized zoom, focus, vertical and horizontal shift,Orientation 360° rotation,Connectivity Inputs HDSDI, 2x DP 1.2, 2x dual link DVI-D, HDBaseT, HDMI 2.0*, RJ 45 Ethernet, , RS232 in, 2x USB,,Control IR, RS232, RJ45 with Suitable lens or better.Recommended Make : NEC /Barco / Digital Projection /Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Ceiling Mounting kit with height adjustment for above projector or better.Recommended Make : Custom /Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 150" Screen Size – 10.6 feet (W) x 6.6 Feet (H); Aspect Ratio 16:10 ,4k Digital Perforated Screen, Gain 1.4 or better:Recommended Make : Harkness/Galalite /Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Structure for 150 " Screen
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 3.7 GHz quad-core Intel Xeon E5 processor with Turbo Boost speeds up to 3.9 GHz, dual AMD FirePro D300 GPUs with 2GB of VRAM each, 12GB of memory, and 256GB of PCIe-based flash storage .Recommended Make : Apple
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Control Surface Studio.Recommended Make : AVID
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Pro Tools HDX Core with Pro Tools Ultimate Perpetual License.Recommended Make : Recommended Make : AVID
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Pro Tools HD OMNI.Recommended Make : AVID
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Pro Tools HD MTRX Base Unit With Madi And Promo.Recommended Make : AVID
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Pro Tools HDX + HD I/O 8x8x8 .Recommended Make : AVID
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Pro Tools SYNC HD.Recommended Make : AVID
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of AES Snake, DB-25 to 8x XLR (4 Male, 4 Female), 12′ Long, for Digidesign HD Systems.Recommended Make : AVID
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 8-channel Snake, XLR Male-DB-25, 12′ Long.Recommended Make : AVID
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 8-channel Snake, DB-25 Male-1/4″ TRS Male, 12′ Long.Recommended Make : AVID
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 8-channel Snake, DB-25 Male-DB-25 Male, 12′ Long.Recommended Make : AVID
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Mini-DigiLink (M) to Mini-DigiLink (M) 1.5 ft.Recommended Make : AVID
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 4-Bay Professional Grade HDD Enclosure.Recommended Make :OWC
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 4TB Internal SATA Hard Drive.Recommended Make :SEGATE
4
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 2TB External hard Disk- 6000.Recommended Make :SEGATE
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Intensity Shuttle with Thunderbolt .Recommended Make :Blackmagic
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Intensity Shuttle for USB 3.0.Recommended Make :Blackmagic
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 24'',16:9 aspect ratio, 4K UHD IPS Monitor,3840 x 2160 Native Resolution,250 cd/m² Brightness,5ms Response Time,1.07 Billion Colors,178°/178° Viewing Angles.Recommended Make :HP/LG/Samsung/Equivalent
2
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 15 Meter Fiber optic supports 4:4:4 @ 60Hz HDMI Male To Male Cable or better.Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 2.5 Sq.mm Speaker Cable for Line array Speakers in meter or better.Recommended Make : Belden /KLotz/Chetan /Equivalent
100
-
-
Mixing Theater- Supply Installation Testing & Commissioning of 4 Sq Mm Speaker Cables for Subwoofers in meter or better.Recommended Make : Belden /KLotz/Chetan /Equivalent
50
-
-
Mixing Theater- Supply Installation Testing & Commissioning of Assorted Cable , Connectors & Conduiting
1
-
-
Mixing Theater- Audio & Video Programming & Calibration Charges
1
-
-
OAT- Supply Installation Testing & Commissioning of Active line array sp eaker with following Specification 12" LF Driver & 1.75 " HF Driver, Frequency Response 49 Hz - 18 kHz,Frequency Range 44 Hz - 20 kHz,Nominal Coverage 90° H x 18° V, Maximum SPL 131dB,Power Output HF: 500 W continuous LF: 500 W continuous or better Recommended Make : Meyer sound /QSC / K- Array /Equivalent
4
-
-
OAT- Supply Installation Testing & Commissioning of Active Loudspeaker with Following Specification 15" LF,6.5" MF,1.75" HF,Frequency Response 35 Hz to 18 kHz,Frequency Range 33 Hz to 20 kHz ,Maximum SPL 134 dB peak,75° conical Coverage or better Recommended Make : Meyer sound /QSC / K- Array /Equivalent
2
-
-
OAT- Supply Installation Testing & Commissioning of Active Subwoofer with following Specification Single 18" Rated power 2000Watts @ peak /1000Watts @ continous Frequency Response 40 Hz to 112 Hz,Frequency Range 37 Hz to 129 Hz,Maximum SPL 135 dB or better Recommended Make : Meyer sound /QSC / K- Array /Equivalent
2
-
-
OAT- Supply Installation Testing & Commissioning of 22 Channel Digital Mixer with following Specification 7" touch capacitive display , 16 Mic/Line input , 2 Stereo Input , Stereo USB Input , 4 Band parameter Equalizer, 99 User Scene & 120 Factory Presets ,mixer control app for Android & IOS ,MP3 playback direct from USB or better Recommended Make : Allen Heath/QSC/Midas /Equivalent
1
-
-
OAT- Supply Installation Testing & Commissioning of Stage Monitor with following Specification 2000W Class D Amplifier with inbuild DSP, 12 inch LF Driver& 1.4" HF Driver ,Frequency Response 50 Hz - 20 kHz,Frequency Range 45 Hz - 20 kHz, Maximum SPL 132dB, Axisymetric Coverage angle 75 Degree Or better Recommended Make : Meyer sound /QSC / K- Array /Equivalent
2
-
-
OAT- Supply Installation Testing & Commissioning of Speaker Mounting Pole Recommended Make : Meyer sound /QSC / K- Array /Equivalent
2
-
-
OAT- Supply Installation Testing & Commissioning of Wireless Handheld Mic with single channel Wireless Receiver & Transmitter Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
4
-
-
OAT- Supply Installation Testing & Commissioning of Wireless Lapel Mic with Frequency Response: 60 Hz – 12 kHz,Sound Pressure: 139 dB,Transducer Type: Condenser,Polar Pattern: Cardioid, Transmitter Operating Range (up to): 100 m nInput impedance: 1000 kΩ Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
OAT- Supply Installation Testing & Commissioning of Headworn Mic ,bodypack Transmitter with Receiver Recommended Make : Beyerdynamic/Shure/Revolabs /Equivalent
2
-
-
OAT- Supply Installation Testing & Commissioning of 9U Rack with Accessories or better Recommended Make : Custom/Equivalent
1
-
-
OAT- Supply Installation Testing & Commissioning of 1.8 Meter HDMI Male To Male Cable in meter or better Recommended Make : Kramer/ Grand Logic/Extron /Equivalent
1
-
-
OAT- Supply Installation Testing & Commissioning of 2.5 Sq.mm Speaker Cable for Line array Speakers in meter or better Recommended Make : Belden /KLotz/Chetan/Equivalent
200
-
-
OAT- Supply Installation Testing & Commissioning of 2 Core Microphone cable in meter or better
Recommended Make : Belden /KLotz/Chetan/Equivalent
500
-
-
OAT- Supply Installation Testing & Commissioning of Assorted Cable , Connectors & Conduiting Recommended Make : Custom/Equivalent
1
-
-
Part - 9 STP works
-
-
-
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 Sq M on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. - All kinds of soil
22.104
-
-
Providing and laying cast in situ cement concrete 1:4:8 including shuttering, form work, dewatering, compacting, curing etc complete - All work up to plinth level (1 Cement: 4 Sand: 8 graded stone aggregate 40mm size)
6.834
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : Foundations, footings, bases of columns, etc. for mass concrete
12.48
-
-
Providing and removing centering and shuttering including strutting, propping etc. and removal of form work for all heights : walls including attached pilasters, buttersses, plinth and string courses etc
59.8
-
-
Providing TMT Steel reinforcement Fe-500D or more for R.C.C. work including straightening, cutting, bending, hooking, placing in position, laping and /welding wherever required, tying with binding wire and anchoring to the adjoining members wherever necessary all complete as per design ( laps, hooks and wastage shall not be measured and paid) cost of materials, labour, HOM of mahcinery complete as per specification - upto plinth level.
886
-
-
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)
11.8125
-
-
Providing and laying in position machine batched and machine mixed design mix M-25 grade BMC/RMC cement concrete for reinforced cement concrete work, using cement content as per relavant IS code and approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.- All works upto plinth level
9.7935
-
-
Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineerin- charge. The product performance shall carry guarantee for 10 years against any leakage.
39.9
-
-
Providing 12 mm thick smooth / sponge finished plaster for internal and external surfaces with cement plaster of mix : 1:6 at all levels including scaffolding, curing etc all complete and as directed
127.31
-
-
Providing and applying two coats of acrylic emulsion with Ist quality acrylic emulsion, having VOC (Volatile Organic Compound) content less than 50 grams /litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, including preparation of surface to remove all dirt, dust, mortar drops and other foreign matters, preparing the surface even, and sand paper smooth, cost of materials, labour, complete as per specification.
40.16
-
-
Providing, supplying, erection and commissioning of packaged Sewage treatment plant with SBR Technology - 40 KLD capacity including required design and detailed engineering with all necessary accessories plant .. etc complete for satisfactory completion as per the requirement and as directed by the Engineer-in-charge
1
-
-
Evaluation Notes How It Works ?
Potential Partner
Select Your Requirements