Kerala State Film Development Corporation Limited Tender

Providing & fixing of the acoustical mineral fiber ceiling tile of 0.75NRC value on the 'T' 'T' Grid system from the Armstrong, AMF, Ecophon or any euivalent approved in the exit passege, including cutting of spot light , Sprinkler & any other related services cut out providing necessary 6mm thk ply support & redoing the same in good finish complete.Work will be carried out as per drawing & instruction of Acoustic consultant /site Engineer /Architect.

Providing & fixing false ceiling in 01 layer of 12.5mm thk Indian Gypsum Plain board with 50mm thk 1000gsm denisty micron in between G.I frame work FRAME - G.I.frame fabricated with 45 x 15 x 0.8 mm thk Intermediate 'C' channel @ 1220mm c/c in one Direction & Ceiling sections 80 x 26 x 0.5 @ 450mm c/c in other direction including perimeter channel as required & 25x25x0.55mm ceiling angle securely fixed to structural truss / members above @ 1220mm c/c, last ceiling angle not more than 610 mm from adjacent wall, connecting clips etc as required with 50mm thk 1000 gsm density micron in Black RP Tissue bag, including scaffolding, cutting of spot light, AC diffuser, return air grill, Sprinkler & any other services cutout & providing necessary 6mm thk ply support & redoing the same in good finish etc complete. Work will be carried out as per drawing & instruction of Acoustc consultant / Site Engineer /Architect JOINTS - All joints of panels filled and finished with India Gypsum jointing compound jointing tapes etc. complete as per manufacturer specification for joint TOP COAT – Entire face of ceiling finished with two coats of top coat as per manufacturers specifications. Three coats of matt paint colour as approved by Architect till the satisfaction of site Engineer

Wall lining treatment

Providing & fixing of 50mm thk 1000gsm density micron in between G.I frame work finish with Black Crape fabric as approved FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface on necessary 50 x 50mm wooden 'T' dutta support with 50mm Air gap, above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction with 50mm thk 1000gsm density micron in between 'C' section frame fixed with chicken mesh backing of G.I 12x12mm square of 24 guage (as per approved sample), including scaffolding, machine screw, etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer /Architect. FINISH: Entire frame /Micron shall be finish with (FR) Black Crape fabric as approved NOTE :All the wood shall be used will be coated with Fire painting & necessary Anti-termite treatment & All the frame work to be considered of Gypsum India company & All the Wooden dutta will have 100x100x12mm thk (Insu Sound-B cap rubber of Supreme ) behind between wall and wooden dutta

Providing & fixing 01 layer of 595 x 595 x 12.5mm thk perforated gypsum tile with 50mm thk 1000gsm density micron in between G.I frame work finish with Black water base paint as marked in drawing (1200 x 1200mm in 'L' shape) FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface on necessary 50 x 50mm wooden 'T' dutta support with 50mm Air gap, above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction with 50mm thk 1000gsm density micron in between 'C' section frame fixed with chicken mesh backing of G.I 12x12mm square of 24 guage (as per approved sample), including scaffolding, machine screw, etc complete.Work 'will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer /Architect. FINISH: Perfoated gypsum tile shall be finish with Black Water base paint as approved NOTE :All the wood shall be used will be coated with Fire painting & necessary Antitermite treatment & All the frame work to be considered of Gypsum India company & All the Wooden dutta will have 100x100x12mm thk (Insu Sound-B cap rubber of Supreme ) behind between wall and wooden dutta

Providing & fixing 1 layer of 08mm thk site Perforated (08mm Random holes) 'E' board with 50mm thk 1000gsm density micron in between G.I frame work as per drawing.FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface on necessary 50 x 50mm wooden 'T' dutta support with 50mm Air gap, above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction with 50mm thk 1000gsm density micron in between 'C' section frame fixed with chicken mesh backing of G.I 12x12mm square of 24 guage (as per approved sample), including scaffolding, machine screw, etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer /Architect. Up to 2.1m wall ht. NOTE :All the wood shall be used will be coated with Fire painting & necessary Antitermite treatment & All the frame work to be considered of Gypsum India company & All the Wooden dutta will have 100x100x12mm thk (Insu Sound-B cap rubber of Supreme ) behind between wall and wooden dutta

Providing & fixing 1 layer of 12.5mm thk Perforated gypum tile with 50mm thk 1000gsm density micron in between G.I frame work as per drawing.FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface on necessary 50 x 50mm wooden 'T' dutta support with 50mm Air gap, above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction with 50mm thk 1000gsm density micron in between 'C' section frame fixed with chicken mesh backing of G.I 12x12mm square of 24 guage (as per approved sample), including scaffolding, machine screw, etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer /Architect. Above 2.1m average Ht. NOTE :All the wood shall be used will be coated with Fire painting & necessary Anti-termite treatment & All the frame work to be considered of Gypsum India company & All the Wooden dutta will have 100x100x12mm thk (Insu Sound-B cap rubber of Supreme ) behind between wall and wooden dutta

Providing & fixing 1 layer of 08mm thk site Perforated (08mm Random holes) 'E' board with 50mm thk 1000gsm denisty micron in between G.I frame work as per drawing.FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface on necessary 50 x 50mm wooden 'T' dutta support with 50mm Air gap, above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction with 50mm thk 1000gsm density micron in between 'C' section frame fixed with chicken mesh backing of G.I 12x12mm square of 24 guage (as per approved sample), including scaffolding, machine screw, etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer /Architect.UP TO 1200MM HEIGHT NOTE :All the wood shall be used will be coated with Fire painting & necessary Anti-termite treatment & All the frame work to be considered of Gypsum India company & All the Wooden dutta will have 100x100x12mm thk (Insu Sound-B cap rubber of Supreme ) behind between wall and wooden dutta

Providing & fixing G.I frame work paneling with 50mm thk 1000gsm denisty micron in between G.I frame work as per drawing.FRAME - G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface on necessary 50 x 50mm wooden 'T' dutta support with 50mm Air gap, above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction with 50mm thk 1000gsm density micron in between 'C' section frame fixed with chicken mesh backing of G.I 12x12mm square of 24 guage (as per approved sample), including scaffolding, machine screw, etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer /Architect. wall panelling above 1.2m ht NOTE :All the wood shall be used will be coated with Fire painting & necessary Anti-termite treatment & All the frame work to be considered of Gypsum India company & All the Wooden dutta will have 100x100x12mm thk (Insu Sound-B cap rubber of Supreme ) behind between wall and wooden dutta

Providing & fixing of the 150mm wide x 37.5mm thk wooden moulding, Design as per Architect approved in side wall panelfix with necessary support on G.I frame work. Moulding will be finished with Melamine polish as approved & satisfied by Architect inccluding machine sanding,applying hard putty, scaffolding etc complete. work will be carried out as per drawing & instruction of acoustic consultant / Site Engineer /Architect. NOTE :All the wood shall be used will be coated with Fire painting & necessary Antitermite treatment. RAll the G.I frame work to be considered of Gypsum India company

Providing & fixing of the 50mm wide x 37.5mm thk wooden moulding, Design as per Architect approved in side wall panelfix with necessary support on G.I frame work.Moulding will be finished with Melamine polish as approved & satisfied by Architect inccluding machine sanding,applying hard putty, scaffolding etc complete. Work will be carried out as per drawing & instruction of acoustic consultant/ Site Engineer /Architect .NOTE :All the wood shall be used will be coated with Fire painting & necessary Antitermite treatment.All the G.I frame work to be considered of Gypsum India company

Providing & fixing G.I frame work for Black PP fabric masking as per drawing.FRAME -G.I.frame fabricated with 50 x 37.5 x 0.5 G.I 'C' section @ 1220mm c/c in horizontal direction fixed to or away from wall surface with top & bottom section and 'necessary 50 x 50mm wooden dutta if any required as per site condition, Above 'C' section have Ceiling sections of 80 x 26 x 0.5 @ 400mm c/c in vertical direction including scaffolding, machine screw , etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant / Site Engineer /Architect. FINISH: Black PP fabric shall be finish on 75x12mm (FR) ply patty as per shapes,pattern as mentioned in the drawing on G.I frame work NOTE :All the wood shall be used will be coated with Fire painting & necessary Anti-termite treatment & All the frame work to be considered of Gypsum India company and Install PP fabric without wrinkles or folds maintaining horizontal / vertical alignment of warp/ woof of fabric using technique that will not damage the finish of fabric

Providing & fixing of the 19mm thk FR ply Shutter in Black masking for Sound box access finished with Black PP Fabric from outside & Black Paint from inside, including the necessary frame for fixing shutter & hinges-02 no's, Concealed Handle, Bolkage etc complete. Work will be carried out as per drawing & instruction of acoustic consultant /Site Engineer/Architect. Shutter size -750 X 1200mm

Providing / fixing 200mm high skirting in 19mm thk ply fixed on existing frame work.flushed with above panelling,Skirting finish with 1.5mm thk Black Laminate as approve by Architect till satisfaction including cutouts for power sockets.Work will be carried out as per drawing & instruction of acoustic consultant,Site Engineer / Architect.(Basic Rate of Laminate- = Rs - 650/sq.mt)

Providing / Fixing 200mm x 150mm thk teak wood door frame with double rebate as per detail drawing including MS hold fast in plumb line and one coat of Black japan paint & Anti termite treatment on frame, etc complete.Work will be carried out as per drawing & instruction of acoustic consultant / Site Engineer /Architect.

Providing & making of the 125mm thk Acoustical Door shutter in hard wood frame of 75x37.5mm all around both side and intermediate frame of 50x37.5mm @ 600 mm c/c in both direction, keep 50mm thk 1000gsm density micron in between frame both side with 01 layer of 10kg/m2 Tec sound & 01 layer of 12.5mm thk plain gypsum board in between both hardwood frame work, Door Shutter shall be finished with 1.5mm thk Laminate as per Architect, design drawing & pattern. All the edges of the shutter shall be finished with T.W lapping putty as per detail

Providing & fixing of the port hole window 1000mm x 800mm or as per designed in 19 mm fire proof ply with necessary saalwood frame, Ply shall be finished with 1.5mm thk Black Laminate including 12mm thk clear no reflective Modi flat glass with 'U'rubber all around the glass complete in line & level etc,Work will be carried out as per drawing & instruction of acoustic consultant / Site Engineer / Architect. NOTE :All the wood shall be used will be coated with Fire painting & necessary Antitermite treatment

Labour charges for fixing surround speaker bracket on existing ply base in side wall & rear wall as per detail including scaffolding, levelling etc complete.Work will be carried out as per drg & instruction of acoustic consultant /Site Engineer /Architect.

Providing & fixing of the 125mm wide x 12mm thk ply batten fixed on the edge of the cinema steps for supporting the step light. Edge of the ply shall be well projected during the construction of the cinema steps.Work will be carried out as per drawing & instruction of acoustic consultant / Site Engineer / Architect.

Finishing treatment

Providing & fixing stretch fabric gripper system (UK) UPVC Grippers,standard,cove mono,edge, but as required by design & manufacture's specifications.CORE - Fire retardant compressible polyster padding of 25mm thk including scaffolding etc complete.Work will be carried out as per drawing & instruction of Acoustic Consultant/ Site Engineer /Architect. FRAME : Gripper fix on 75 x 12mm ply (fire retardant) patty with 25 mm thk Polyster padding as required by design. INSTALLATION: Installation in accordance with drawings and manufacturer's instruction. Installation of grippers in maximum fabric without wrinkles or folds, maintaining horizontal / vertical alignment of warp /woof of fabric, force fabric edges into clamping jaws, using tools and techniques that will not damage finish of the fabric complete to the satisfaction of the site Engineer-In-Charge. SUBMITTALS : Shop drawings indicating location, size, type,including frame, core & fabric finish components, for each panel in project. Drawings indicating construction details of interface with adjacent construction. The rates shall includes the shapes, pattern as mentioned in the drawing indicating graphics if any.

Providing & fixing of Black Crape fabric on perforated gypsum ceiling tile with 75x12mm thk (FR) Ply patty as per grooves & pattern mentioned in drawing in line & level including scaffolding etc complete, Work will be carried out as per drawing & instruction of Acoustic Consultant / Site Engineer /Architect. Basic Rate of Fabric- = Rs - 225/mtr NOTE : Install Crape fabric without wrinkles or folds maintaining horizontal / vertical alignment of warp/ woof of fabric using technique that will not damage the finish of fabric

Labour charges for Fixing departmentally supplied white perforated Galalite screen on the M.S screen frame including scaffolding. Work will be carried out as per drawing & instruction of acoustic consultant, Site Engineer /Architect

Providing & fixing of 800gsm cut pile carpet with 06mm thk underlay to be fixed on cinema tiers as per design & drawing of Architect, Surface shall be clean properly before installing carpet, Carpet shall be fix with adhesive as per manufacture specifications, in perfect line & level , no joints should be visible, All as per approved design, shade & make etc complete. Complete work will be carried out as per drawing & instruction of site Engineer/Architect, (Basic Rate of Carpet- = Rs - 800/sq.mt)

Applying 3coats of Plastic paint of approved make & shade of Asian paint or Nerolac or ICI Dulux, Surface shall be clean and sanding by sand paper & applying one coat paint & putty & again sanding & leveling & two coats of paint till approved & satisfaction of Architect to shade colour including scaffolding etc complete work will be carried out as per drawing & instruction of acoustic consultant /Site Engineer/Architect

Fabrication work

Providing & Installing screen supporting from floor in 2mm thk 18 guage M.S pipe 50mm dia external frame and 25mm dia internal frame including Elbow as per detail drawing with 100x100x19mm thk (Insu Sound-Bcap rubber of Supreme) backing on floor & slab above behind base plate, MS pipe shall be finished with Black Paint, Work will be carried out as per drawing & instruction of Acoustic consultant, site Engineer/Architect.

Providing & fixing of M.S speaker platform in M.S angle of 75mm X 75mm as per drawing with 02 layers of 19mm thk Ply above frame with fabrication, levelling etc complete including one coat of red oxide paint and two coat of Black paint as approved M.S. angle will be supported at 1200mm c/c with the 'L' bracket, The bracket will have 12mm thk (Insu Sound-B cap rubber of Supreme) in between wall & bracket. The instruction of acoustic consultant /Site Engineer /Architect.depth of the platform will be as per site.Work will be carried out as per drawing & direction as per Engineer in charge

Providing & fixing of the Black color powder coated M.S pipe hand railing of 50mm dia along the wall fixed with 100 x 100 x 6mm thk Base plate support system with 100 x 100 x 12mm thk (Insu Sound-Bc ap rubber of Supreme), behind base plate on the wall @ 1200mm c/c in line & level as per site, etc complete. Work will be carried out as per drawing & instruction of acoustic consultant / Site Engineer /Architect.

Providing & fixing of M.S 'C' channel of 100 x 50 x 6mm @ 1200mm C/C as per drawing & wherever required as per site requirement for supporting A/C ducts, False 'ceiling with necessary support from 'I' beam including weilding, grinding, scaffolding, Channel shall be finished with 01 coat of Red oxide & 02 coat of Black Paint etc complete. Work will be carried out as per drawing & instruction of structural consultant /site Engineer/Architect.

Providing & fixing of the M.S speaker platform in M.S angle 75x 75mm as per drawing for the sub woofer Base for Atmos speaker supported from the wall with 12mm thk (Insu Sound-B cap rubber of Supreme) between the M.S frame & wall to avoid Vibrational sound in structure, including 2 layers of 19mm thk ply & 01 layer of 19mm thk rigid rubber on ply complete with necessary weilding, grinding levelling etc. complete including one coat of Red oxide paint and two coat of Black paint as approved by Architect, Vendor to give necessary shop drawing for the same for structural consultant approval Work will be carried out as per drawing & instruction of acoustic consultant/Site Engineer/Architect (Platform size : 1350 X 1000mm)

Providing & fixing of the M.S bracket in square box pipe of 50x50mm for the speaker bracket for Atmos speaker from the ceiling to be supported from the sub frame of M.S truss girder with necessary base plate & 12mm thk(Insu Sound-B cap rubber of Supreme) at Junction to avoid Vibrational sound in structure, including necessary weilding,grinding finished with 1coat of Red oxide & 2 coat of Black Paint etc complete.Vendor to give necessary shop drawing for the same for structural consultant approval Work will be carried out as per drawing & instruction of acoustic consultant/Site Engineer/Architect.

Providing & Fabricating 1200mm x 900mm x 450mm(for tender to be provided as per system supplier’s drawings) fire cabinet boxes in all the theatres made from 12mm thk 'E'-board finished with 1.5mm matt Black laminate. 100x30 Salwood shutter frame. 6mm Modi Flat Clear Glass with frosted film fitted in the frame with 6mm neoprene ‘U’ gaskets. 2 UNION make heavy duty SS hinges. 1UNION Matt Black water based paint etc complete for intended use in every respect, Work will be carried out as per drawing & instruction of MEP consultant / Site Engineer/Architect

Isolation Treatment

Providing & fixing - 03 layer of 12.5mm thk plain gypsum board One side of M.S stud section frame work in staggered joint screwed to stud frame as per drawing FRAME - GI Stud frame fabricated with 146 x 34 x 36 x .55 'C' section @ 600 mm c/c in one diection with necessary 50 x 50mm wooden 'T' support as required as per site condition, including 75mm thk 1000gsm density micron fixed with chicken mesh back of G.I 12x12mm square of 24 guage & Black Crape fabric from back side of framing,including scaffolding etc complete.Work will be carried out as per drawing & instruction of Acoustic consultant/ Site Engineer / Architect. JOINTS - All joints of Gypsum panels filled and finished with India Gypsum jointing compound, jointing tapes etc.complete as per manufacturer specification for joint TOP COAT – Final Layer of Gypsum shall be finished with Black Paint as approved by Architect / till the satisfaction of site Engineer

Providing & fixing of size 450 x 300 x 19mm thk Ply for the speaker bracket fixing on wall with 100 x100 x 19mm thk (Insu Sound-B cap rubber of Supreme) 04 nos in between ply & wall as per detail etc complete. Work will be carried out as per drawing & instruction of acoustic consultant /Site Engineer /Architect.

Providing & making of the isolation base for the main speaker as per drg in 02 layer of 19mm thk ply & in between ply have 01 layer of 100 x 100 x 25mm thk rigid rubber pads on all four sides & keep 25mm thk 32kg/m3 gsm density glass wool in between ply.Base shall be covered with Black resin & shall be mounted on 2 layer of 150 x 150 x 25mm thk rubber of sylomor @ 04 corners, etc complete as per detail. Work will be carried out as per drawing & instruction of acoustic consultant /Site Engineer/Architect. ( Isolation Base size = 750mm X 600mm )

Providing & making of the isolation base for the subwoofer as per drg in 02 layer of 19mm thk ply & in between ply have 01 layer of 100 x 100 x 25mm thk rigid rubber pads on all four sides & keep 25 mm thk 32 kg/m3 density Glass wool in between ply The base shall be covered with Black resin & shall be mounted on 2 layer of 150 x 150 x 25 mm thk rubber of sylomor @ 04 corners, etc complete as per detail. Work will be carried out as per drawing & instruction of acoustic consultant /Site Engineer/Architect. ( Isolation Base size = 1200mm X 900mm )

Furniture

Supply and installation of office table with BIFMA,AIOTA,Greengaurd ,GRIHA and IAQ certifications .Table size should be 1200 Width x 600 Depth x 740 Height . The top should be made from 25 mm thick pre- laminated board . All the edges are sealed with 2 mm thick PVC edge band all around. Side panels should be made from 25 mm thick pre- laminated paticle board . All the edges are sealed with 2 mm thick PVC edge band on the user side and 0.8 mm on the top and bottom side .The side panels have 2 glide screws each for levelling of the desk. Modesty panel should be made from 18 mm thick pre- laminated particle board . All the edges are sealed with 0.8 mm thick PVC edge band all around. Freestanding Pedestal should be made from 18 mm pre- laminated particle board with a combination of 2 mm and 0.8 mm PVC edge band on all the exposed surfaces as per requirement . The drawers are provided with suitable slides for smooth operation . All the pedestal drawers are centrally locked with a single key .Approved Make Godrej ,Herman miller & Haworth

Supply and installation of Executive table with BIFMA,AIOTA,Greengaurd ,GRIHA and IAQ certifications .Overall product dimension should be 1200 L x 600 D x 750 Ht .Work Surface Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Gromet provided on work surface for wire management Modesty Panel : Made of 25mm Thick Prelaminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Understructure: Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to 1S-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Hinge Door Storage : Made of 25mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.Handle is provided for ease of opening.Storage is provided with cam lock for security.Approved Make Godrej ,Herman miller & Haworth

Supply and installation of Executive table with BIFMA,AIOTA,Greengaurd ,GRIHA and IAQ certifications . Table size should be 1200 Width mm x 600 Depth mm x 728 Height mm. Top should be 18 mm thick Pre laminated particle board all work surface edges should be having duly sealed with 2 mm thick PVC edgebanding. Understructure Modesty Panel 18 mm thick Pre laminated particle board . The Rectangular frame should be fabricated component in 1.2 mm thick CRCA , Finish : powder Coat( epoxy polyster) . Leg should be fabricated component in 38 mm x 25 mm 1.2 mm thick MS ERW ATube ,finish powder coat ( epoxy polyster).The plastic cap for cable travel should be injection moulded polypropylene and leveler glide for should be nylon 6 & MS bolt. The storage should be having shell and drawer tray 0.6 mm thick CRCA Finish powder coat (epoxy polyster) plus the drawer front should be 0.8 mm thick CRCA Finish powder coat (epoxy polyster) plus lock with 10 lever and handle and leveller. The wire management should be horizontal wire carrier 0.7 mm thick CRCA Finish powder coat (epoxy polyster) and vertical wire carrier 0.8 mm thick CRCA Finish powder coat (epoxy polyster) . Approved Make Godrej ,Herman miller & Haworth

GRIHA, GREENGUARD,AIOTAand BIFMA certified certified Chair .SEAT/BACK ASSEMBLY: The cushioned seat assembly consists of seat base moulded in glass-filled Poly-amide, moulded Polyurethane foam & upholstered with high stretch knitted polyester fabric. The cushioned back assembly consists of back inner moulded in Polypropylene in-situ moulded with Polyurethane foam & upholstered with high stretch knitted polyester fabric. *Full Back Size: 45.5 cm. (W) x 53.0 cm.(H). HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam used in seat and back cushion is moulded in Density 45+2 kg/m3, and hardness load 16+2 kgf as per IS:7888 for 25% compression. TILT MECHANISM, SPINES & SPINE CONNECTOR: The seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi-dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. The cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during postures changes. The “S” shaped spines moulded in high strength glass-filled Poly-amide and the spine connector moulded in glass- filled Poly-amide form the back-spine structure involved in multi-dimensional recline motion. The variable tilt angle recline motion can be adjusted with 3 position Tilt Limit feature which is inbuilt in seat base and the tension (return force) is user weight dependent. ADJUSTABLE ARMRESTS: The assembly consists of armrest housing sliding over the armrest structure, both moulded in glass-filled Poly-amide. The height adjustment feature is button operated having adjustment of 6.6+0.5 cm. The Armrest Top is made up of integral skin PU moulded over plastic inner moulded in glass-filled Poly-amide. PNEUMATIC HEIGHT ADJUSTMENT: The seating height can be adjusted with pneumatic gas-lift having an adjustment stroke of 9.2+0.3 cm. PEDESTAL ASSEMBLY: The pedestal is injection moulded in glass-filled Poly-amide and fitted with 5 nos twin wheel castors. The pedestal is 66.0+.0.5 cm. pitch centre diameter and 76.0+1.0 cm. with castors. TWIN WHEEL CASTORS: 5nos. twin wheel castors are injection moulded in Poly-amide having 5.0+.01cm wheel diameter and assembled to the pedestal. Approved Make Godrej ,Herman miller & Haworth

GRIHA, GREENGUARD,AIOTAand BIFMA certified certified Chair .The seat assembly should be made up of 1.2 ±0.1cm. thick hot-pressed plywood measured as per QA method described in OCP-QLTA-P14-18 and should be upholstered with fabric upholstery covers and moulded Polyurethane foam. The dimensions of seat should be 47.0 cm. (W) x 48.0 cm. (D). The back asembly should be made of powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with contoured lumbar support for extra comfort. The back should be upholstered using Net fabric with high tenacity yarn. The dimensions of back should be 46.5 cm (W) x 64.5 cm (H). The HR polyurethane foam should be moulded with density =45+/-2 kg/m3 and hardness load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests should be injection moulded from black Co-polymer Polypropylene. The mechanism should be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position locking., Tilt tension adjustment. The pneumatic height adjustment should has an adjustment stroke of 11.0 ±0.3cm. The bellow should be 3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal should be injection moulded in black 33% glass-filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors). The twin wheel castors should be injection moulded in Black Nylon. Overall Dimensions of Chair should be Seat Height - min 43.3 to max 54.3cm, Height - min93.5 to max 104.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-76.3 cm.Approved Make Godrej ,Herman miller & Haworth

BIFMA,GRIHA,Greengaurd and Aiota Certified chair.The Seat and Back ate made up of injection moulded high impact strength PolyPropylene polymer compound with indoor grade UV resistance .SEAT SIZE : 52.5 cm. (W) x 53.2 om. (D). BACK SIZE : 51.6 om. (W) x 40.5 om. (H) .M.S. ARMREST :The powder coated ( DFT 50+10 microns ) welded tubular frame is made from dia 2.22 + 0.03 cm x 0.16 +- 0.0128 cm and 3.5 +- 0.03 cm x 1.5 +- 0.03 cm x 0.16 + 0.0128 cm M.S. E.R.Wtube. S.S. UNDERSTRUCTURE OPTION FOR CAFE CHAIR: The tubular welded frame is made from Dia 2.22 +- 0.03 cm x 0.12 +- 0.0128 cm and 3.5 + 0.03 cm x 1.5 +- 0.03 cm x 0.12 + 0.0128 cm Stainless Steel 202 grade tube. The tubes are buff polished to give shiny finish. POWDER COATED BEAM STRUCTURE FOR LOUNGE :The powder coated ( DFT 50410 microns ) welded Beam M.S. Structure is made from 5.08 +- 0.03 cm x 5.08 +- 0.03 cm x 0.16 x 0.0128 cm. The 0.315 +- 0.008 cm thk HR steel plate is welded to beam for fixing seat and back frame. The powder coated ( DFT 50410 microns ) welded Leg M.S. Structure is made from 5.08 +0.03 cm x 5.08 + 0.03 cm x 0.16 x 0.0128 cm and 5.08 + 0.03 cm x 2.45 + 0.03 cmx 0.16 + -0.0128 cm.SHOE : The shoes are made of high impact'strength PolyPropylene polymer compound with indoor grade UV resistance and pressed fitted with tubular frame. ARMREST : The Armrest are made of high impact strength PolyPropylene polymer compound with indoor grade UV resistance and assembled over the tubular frame.OUTER DIMENSION: 31.5+-0.1cm. (W) X 47.00.1cm. (D) PAPER TRAY: The paper tray is made of 0.4 +0/-0.005cm. M.S.rod which is spot welded to.form a mesh-type structure. It is powder coated ( DFT 50+ 10 microns ).SIZE: 40.10m. (W) X 36.1cm. (D) X 22.0 om (H).UPHOLSTRY- An upholstry cover can be retro fitted on to seat and back. The seat cover is made from High abrasion resistance fabric with foam lamination and 2.5 om PU Foam insert. The back cover is made from High abrasion resistance fabric with foam lamination and 0.1 cm PU Foam insert.Approved Make Godrej ,Herman miller & Haworth

BIFMA,GRIHA,Greengaurd and Aiota Certified Vertical Filing Cabinets whcih use less floor space. Size of 4 Drawer VFC should be 1320mm(H) X 470mm(W) X 620mm(D). All the components should be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top, Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm. The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle should be integrated into Metal Drawer for easy pull out convenience. There should be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ / ‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System should be provided along with Shooting Bolt Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which ensures that when one drawer is opened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide should be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular plate pop should be riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to back should also be available. The finishing should include Epoxy powder coated to the thickness of 50 microns (+/- 10).Approved Make Godrej ,Herman miller & Haworth

Supply and installation of 3 +2+1 sofa with Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is 221mm thk. [moisture resistance & termite proof as por I5:303] & pinewood are of cross sections 22x64m,34xB4mm & 16x35mm without having maior knots & defects on the surface. Zigzag spring of da. 3.8mm is mounted on the seat structure using plastic spring mounting cifp for support & additional cushioning purpose.Non woven fabric is stapled on the seat structure frame above the spring asly. 10 avoid direct contact between the metal springs and the seat foam. This prevents seat foam from tearing. Powder coated IMS support pipe is fitled with the wooden seat frame o give additional strength to the structure. Complete understructure is made by ging, naling & stapling Foam: Seat is made of PU foam with density 28 kg/m3 with a top layer of supersoft PU foam with density 32 kgim3. Seat front bottor is stapled with the PU foam with density 28 kg/m3.Upholstery: Seat upholstery is made in polyester fabric with partitions.Backrest:Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood 122 1mm thk. [moisture resistance & termite proof as per 15:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knols & defects on the surface. 3mm MDF is stapled on the back of the structure and manjarpat is stapled at the front bottom.Foam: Backrest is made of PU foam with density 28 kg/m3 on the front lumber portion and the shoulder area has supersoft PU foam with density 32 kg/n3. This is covered with a top layer of supersoft PU foam with density 32 kg/m3. The top surface has foam with density 32 kg/m3. Complete back surface & underarm of backrest s glued with the PU foam with density 28 kg/d.Upholstery: Backrest upholstery is made in polyester fabric and has a marjarpat cloth for pulling to‘accentuate the lumbar area. A throw cover is draped over the backrest, which can be dry cleaned.Coffee Tray: Three seater sofa has a Coffee Tray made up of powder coated 2mm thk Aluminum sheet.Logs: Plastic legs with the M8 stud are fitted a the bottom surface of the Armrest LH & RH.Assembly: Upholstered seat, backrest, armrest-LH & amrest-RH are assembled together with the M8 bolts,11s & washer. Then a non-woven is stapled on the bottom surface to cover the structure.Approved Make Godrej ,Herman miller & Haworth

Supply and installation of 3 +2+1 sofa with Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is.21mm thi. [moisture resistance & termite proof as per 15:303] & pinewood are of cross sections 22464mm,34x64mm & 16x35 without having major knots & defects on the surface. Zigzag spring of dia. 3.8mm is mounted on the seat structure using plastic spring mounting clip for support & additional cushioning purpose.Non woven fabric is stapled on the seat structure frame above the spring asly. to avoid direct contact between the metal springs and the seat foam. This prevents seat foam from tearing. Powder coated MS support pipe is.fitted with the wooden seat frame to give additional strength to the structure. Complete understructure is made by gluing, nailing & stapling.Foam: Seat is made of PU foam with density 28 kg/m3 with a top layer of supersoft PU foam with density 32 kgim3. Seat front bottom is stapled with the PU foam with density 28 kg/m3,Upholstery: Seat upholstery is made in polyester fabric with partitions.Backrest : Understructure: Understructure is made up of combination of plywood & pinewood members. Plywood is 121mm thk. moisture resistance & termite proof as per IS:303] & pinewood are of cross sections 16x35mm & 16x74mm without having major knots & defects on the surface. 3mm MDF is stapled on the back of the. structure and manjarpat is stapled at the front bottom.Foam: Backrest is made of PU foam with density 28 kgim3 on the front lumber portion and the shoulder area has supersoft PU foam with density 32 kg/m3. This is covered with a top layer of supersoft PU foam with density 32 kgim3. The top surface has foam with density 32 kg/m3. Complete back surface & underarm of backrest is glued with the PU foam with density 28 kg/m3 Upholstery: Backrest upholstery is made in polyester fabric and has a manjarpat cloth for pulling to ‘accentuate the lumbar area. A throw cover is draped over the backrest, which can be dry cleaned.Legs: Rubberwood [Grade-A] legs with the MB stud are fitted at the bottom surface of the Armrest LH & RH. Legs are coated with PU clear coat [mat finish] Assembly: Upholstered seat, backrest, armrest-LH & armrest-RH are assembled together wilh the M8 bolts, nuts & washer. Then a non-woven is stapled on the bottor surface to cover the structure .Packet: Each packet contains one assembled sofa without legs and a separate hardware packet containing 4 nos. of plastic legs .Approved Make Godrej ,Herman miller & Haworth

Theatre Engineering Furniture and Accessories

ABD metal counter chair ,black,preassembled arm chair

Desk top 1TB ,SSB with OS and PC core i3 HDMI & VGA ,3 year on site warrenty

A4 black and white laser all in all printer (MSP ). Print,scan,copy ,print speed up to 22 ppm ,print resolution 600x600 dpi,USB ,ethernet and wireless connectivity

Thermal printer 3 inch.Rugte KRP 326-3" thermal receipt printer

Cash counting machine with fake note detection .UV,MG,IR Detection during counting .Automatic half note ,chain note ,double note detection .Automatic start,stop and clearing with batching.Adding and self examination display function .

UPS

Supply, installation, testing and commissioning of uninterrupted power supply system including giving all connections to input & output electrical power panel boards/DBs etc. with necessary arrangements and accessories, complete in all respect. For Projector System BARCO 4K projector SP4K15C - 5kVA Refer to technical specifications - UPS system and battery Charger

Supply, installation, testing and commissioning of uninterrupted power supply system including giving all connections to input & output electrical power panel boards/DBs etc. with necessary arrangements and accessories, complete in all respect. For Sound System Dolby Atmos - 20kVA Refer to technical specifications - UPS system and battery Charger

SPEAKER WIRING

Stage speaker LCR HF/MF tri AMP Providing & Supply, installation, testing & commissioning of audi speaker wiring using 2 Nos. 4 Sq.mm multistranded flexible FRLS PVC wire in Existing FRLS medium guage PVC conduit with accessories for auditorium speakers laying on surface / concealed as required.

Stage speaker LCR LF tri AMP Providing & Supply, installation, testing & commissioning of audi speaker wiring using 2 Nos. 6 Sq.mm multistranded flexible FRLS PVC wire in Exissting FRLS medium guage PVC conduit with accessories for auditorium speakers laying on surface / concealed as required.

Surround Subwoofer Providing & Supply, installation, testing & commissioning of audi speaker wiring using 2 Nos. 6 Sq.mm multistranded flexible FRLS PVC wire in Exissting FRLS medium guage PVC conduit with accessories for auditorium Surround Subwoofer laying on surface / concealed as required.

Sub woofer Providing & Supply, installation, testing & commissioning of audi speaker wiring using 2 Nos. 6 Sq.mm multistranded flexible FRLS PVC wire in Exissting FRLS medium guage PVC conduit with accessories for auditorium Surround Subwoofer laying on surface / concealed as required.

Surround Spekers for TOP ,Right Side, Left Side , Back Side Providing & Supply, installation, testing & commissioning of audi speaker wiring using 2 Nos. 4 Sq.mm multistranded flexible FRLS PVC wire in Existing FRLS medium guage PVC conduit with accessories for auditorium speakers laying on surface / concealed as required.

Condute with plasctic pipe and fitting Supply and installation of following sizes of FRLS Medium gauge PVC conduit recess/surface in Floor/ wall including all accessories, GI fish wire, fixing hardware etc. including chasing the wall / floor and plastering the chased portion and making the good the damages etc. complete as required for main,submains MEDIUM GAUGE PVC CONDUIT (25MM)

Condute with plasctic pipe and fitting Supply and installation of following sizes of FRLS Medium gauge PVC conduit recess/surface in Floor/ wall including all accessories, GI fish wire, fixing hardware etc. including chasing the wall / floor and plastering the chased portion and making the good the damages etc. complete as required for main,submains MEDIUM GAUGE PVC CONDUIT (32MM)

Sound rack Providing & Fixing one no. sound rack for installation of all amplifier and processor

Sound Alingment & commesioning Carry out filter sound alingment of every speaker output with each amplier and commissioning the sound processor as per good sound quality feeder level.

Projector Stand Table size 1.2x0.8m- Made of MS sheet of 2mm thick