Kerala State Electronics Development Corporation Limited Tender

10W (RGBW) - floodlight/ accent effect Supply of RGBW Surface mounted Wide beam Round Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 24Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +50°C, Operating Humidity: 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

Supply of RGBW surface ace mounted Narrow beam Square Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 9W to 280Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should beIP66or higher. Housing should be made of Die cast Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature:-10°C to +50°C, Operating Humidity: 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE / LUMILED / OSRAM / NICHIA/ / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

DMX-512 Controller DMX Controller with 2 Universe. (Without cloud) DMX Controller - Stand Alone Interface with a combination of internal memory and micro SD card with connector blocks and DIN RAIL mountable. Controller should be capable of handling 1024 DMX channels extendable to 2048 channels with a simple firmware update. Programming the controller and saving the scenes, memories, triggers, and various integration settings from PC/Laptop running Windows, MAC OS or Linux. Programming should be possible over USB, LAN and remotely over INTERNET. The controller should be capable of assigning scene/program triggers with RS232, UDP / DMX IN, Real Time Clock, and calendar, 12direct and 31multiplex programmable dry contacts (On, On/Off, Release, Restart, Scene Priority, UP/DOWN etc..). A maximum of 2500 scenes across 5 different zones capacity. Input power voltage: 5~24V DC with USB C cable included and equipped with an additional connector block input. The controller should have DMX to adopt to various types of projects and Lighting configurations.(storage size of the internal memory/SD card to be mention. Also the system shall be powered through a suitable capacity Online UPS with min back up.) The system shall be housed in a suitable equipment rack having adequate cooling and powering option. Luminaire Type : DMX-512 Controller

4- Port DMX-Splitter cum Booster 6 - Port Splitter Cum Booster. 6 output DMX Splitter & Booster works as DMX signal amplifier and signal splitter. The signal amplification/boosting function should amplify the DMX master controller’s output DMX signal up to 200 meters by using an ideal DMX cable. The DMX Splitter & Amplifier’s all six output terminals are optically isolated. All six outputs should have an independent output 9V coil transformer to boost the DMX signal. The Splitter/booster should be capable of working on 220V/230V line voltage AC. Operating temperature shall be -10 to 50 Deg Celsius. Protection Rating IP 20. Splitter/Booster should be equipped with included mounting brackets which allow multiple installation options for rack, floor, surface, ceiling mounting .3 pin XLR Connectors for IN and OUT connections for firm and solid connection for DMX signal. The signal strength of DMX signal should be above 4 V at each output for reliable signal strength for a maximum of 20 lights in a chain and to 200 meters maximum length to the last light. Equipped with an accessible fuse carrier and supplied with 1.5sq. mm 3 core cable pre-connected. The system shall be housed in a suitable equipment rack having adequate cooling and powering option. Luminaire Type : Signal Splitter

FACADE LIGHTING BOQ FOR MISKHAL MASJID

18W (WW)-1000mm Wall Washer/ Wall Grazing Luminaire Supply of Warm white Wide beam Linear Wall Washer luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10w to 96W at steady state full intensity. Luminaire should be able to run on DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Extruded Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +50°C, Operating Humidity: 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE / LUMILED / OSRAM / NICHIA/ / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Linear wall washer

10W (WW) - floodlight/ accent effect Supply of Warm white Surface mounted Wide beam Round Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +50°C, Operating Humidity: 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

The system shall be powered through a suitable capacity Online UPS with min back up.) The system shall be housed in a suitable equipment rack having adequate cooling and powering option.

FACADE LIGHTING BOQ FOR CSI CHURCH

24W (RGBW) -1000mm Wall Washer/ Wall Grazing Luminaire Supply of RGBW Wide beam Linear Wall Washer luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10w to 96W at steady state full intensity. Luminaire should be able to run on DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Extruded Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +50°C, Operating Humidity: 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE / LUMILED / OSRAM / NICHIA/ / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Linear wall washer

36W (RGBW) - floodlight/ accent effect Supply of RGBW Surface mounted Wide beam Round Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25°C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature: -10°C to +50°C, Operating Humidity: 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDs of CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

DMX-512 Controller DMX Controller with 2 Universe (Without cloud) DMX Controller - Stand Alone Interface with a combination of internal memory and micro SD card with connector blocks and DIN RAIL mountable. Controller should be capable of handling 1024 DMX channels extendable to 2048 channels with a simple firmware update. Programming the controller and saving the scenes, memories, triggers, and various integration settings from PC/Laptop running Windows, MAC OS or Linux. Programming should be possible over USB, LAN and remotely over INTERNET. The controller should be capable of assigning scene/program triggers with RS232, UDP / DMX IN, Real Time Clock, and calendar, 12direct and 31multiplex programmable dry contacts (On, On/Off, Release, Restart, Scene Priority, UP/DOWN etc..). A maximum of 2500 scenes across 5 different zones capacity. Input power voltage: 5~24V DC with USB C cable included and equipped with an additional connector block input. The controller should have DMX to adopt to various types of projects and Lighting configurations.(storage size of the internal memory/SD card to be mention. Also the system shall be powered through a suitable capacity Online UPS with min back up.) The system shall be housed in a suitable equipment rack having adequate cooling and powering option. Luminaire Type : DMX-512 Controller

4- Port DMX-Splitter cum Booster 6 - Port Splitter Cum Booster 6 output DMX Splitter & Booster works as DMX signal amplifier and signal splitter. The signal amplification/boosting function should amplify the DMX master controller’s output DMX signal up to 200 meters by using an ideal DMX cable. The DMX Splitter & Amplifier’s all six output terminals are optically isolated. All six outputs should have an independent output 9V coil transformer to boost the DMX signal. The Splitter/booster should be capable of working on 220V/230V line voltage AC . Operating temperature shall be -10 to 50 Deg Celsius. Protection Rating IP 20. Splitter/Booster should be equipped with included mounting brackets which allow multiple installation options for rack, floor, surface, ceiling mounting .3 pin XLR Connectors for IN and OUT connections for firm and solid connection for DMX signal. The signal strength of DMX signal should be above 4 V at each output for reliable signal strength for a maximum of 20 lights in a chain and to 200 meters maximum length to the last light. Equipped with an accessible fuse carrier and supplied with 1.5sq.mm 3 core cable pre-connected. The system shall be housed in a suitable equipment rack having adequate cooling and powering option. Luminaire Type : Signal Splitter

FACADE LIGHTING BOQ FOR PATTALA PALLI

75W (RGBW) - SQUARE PROJECTOR Supply of RGBW Surface mounted Narrow beamRound Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.LEDsof CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Floodlight

135W (RGBW) - SQUARE PROJECTOR Supply of RGBwW Surface mounted Narrow beamRound Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.LEDsof CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Floodlight

36W (RGBW) - floodlight/ accent effect Supply of Warm white Surface mounted Wide beamRound Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDsof CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

10W (RGBW) - floodlight/ accent effect Supply of RGB Surface mounted Narrow beam Round Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements. LEDsof CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

FLEXI STRIP LIGHTS Supply of RGBFlexible Strip with wide beam anglesuitable for outdoor applications of Façade Lighting. Silicon MouldedFlexible tubes with horizontal and vertical bending options are available. Power Consumption should be between 5W/m to 15/m with 120°beam angle. Ingress Protection should beIP 65 or higher. Luminaire should be able to run on DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Power supply: DC 24V, with Operating temperature range: -20°C to +50°C and of LED make: CREE/ OSRAM/ LUMILED/ SEOUL/ NICHIA/ PHILIPS. (Mention the LED beam angle in the spec). Luminaire Type : RGB Strip Light

DMX-512 Controller DMX Controller with 2 Universe (Without cloud) DMX Controller - Stand Alone Interface with a combination of internal memory and micro SD card with connector blocks and DIN RAIL mountable. Controller should be capable of handling 1024 DMX channels extendable to 2048 channels with a simple firmware update. Programming the controller and saving the scenes, memories, triggers, and various integration settings from PC/Laptop running Windows, MAC OS or Linux. Programming should be possible over USB , LAN and remotely over INTERNET. The controller should be capable of assigning scene/program triggers with RS232, UDP / DMX IN, Real Time Clock, and calendar, 12direct and 31multiplex programmable dry contacts (On, On/Off, Release, Restart, Scene Priority, UP/DOWN etc..). A maximum of 2500 scenes across 5 different zones capacity. Input power voltage: 5~24V DC with USB C cable included and equipped with an additional connector block input. The controller should have DMX to adopt to various types of projects and Lighting configurations.(storage size of the internal memory/SD card to be mention. Also the system shall be powered through a suitable capacity Online UPS with min back up.) The system shall be housed in a suitibale equipment rack having adequate cooling and powering option. Luminaire Type : DMX-512 Controller

6- Port DMX-Splitter cum Booster 6 - Port Splitter Cum Booster 6 output DMX Splitter & Booster works as DMX signal amplifier and signal splitter. The signal amplification/boosting function should amplify the DMX master controller’s output DMX signal up to 200 meters by using an ideal DMX cable. The DMX Splitter & Amplifier’s all six output terminals are optically isolated . All six outputs should have an independent output 9V coil transformer to boost the DMX signal . The Splitter/booster should be capable of working on 220V/230V line voltage AC . Operating temperature shall be -10 to 50 Deg Celsius. Protection Rating IP 20. Splitter/Booster should be equipped with included mounting brackets which allow multiple installation options for rack, floor, surface, ceiling mounting .3 pin XLR Connectors for IN and OUT connections for firm and solid connection for DMX signal. The signal strength of DMX signal should be above 4 V at each output for reliable signal strength for a maximum of 20 lights in a chain and to 200 meters maximum length to the last light. Equipped with an accessible fuse carrier and supplied with 1.5sq. mm 3 core cable pre-connected. The system shall be housed in a suitable equipment rack having adequate cooling and powering option. Luminaire Type : Signal Splitter

FACADE LIGHTING BOQ FOR TOWN HALL

20W (WW) - floodlight/ accent effect Supply of Warm white Surface mounted Wide beam Round Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.LEDsof CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

18W (WW)-1000mm Wall Washer/ Wall Grazing Luminaire Supply of Warm white Wide beamLinear Wall Washer luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10w to 96W at steady state full intensity. Luminaire should be able to run on DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Extruded Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.LEDs of CREE / LUMILED / OSRAM / NICHIA/ / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Linear wall washer

DMX-512 Controller DMX Controller with 2 Universe (Without cloud) DMX Controller - Stand Alone Interface with a combination of internal memory and micro SD card with connector blocks and DIN RAIL mountable. Controller should be capable of handling 1024 DMX channels extendable to 2048 channels with a simple firmware update. Programming the controller and saving the scenes, memories, triggers, and various integration settings from PC/Laptop running Windows, MAC OS or Linux. Programming should be possible over USB , LAN and remotely over INTERNET. The controller should be capable of assigning scene/program triggers with RS232, UDP / DMX IN, Real Time Clock, and calendar, 12direct and 31multiplex programmable dry contacts (On, On/Off, Release, Restart, Scene Priority, UP/DOWN etc..). A maximum of 2500 scenes across 5 different zones capacity. Input power voltage: 5~24V DC with USB C cable included and equipped with an additional connector block input. The controller should have DMX to adopt to various types of projects and Lighting configurations.(storage size of the internal memory/SD card to be mention. Also the system shall be powered through a suitable capacity Online UPS with min back up.) The system shall be housed in a suitibale equipment rack having adequate cooling and powering option. Luminaire Type : DMX-512 Controller

4- Port DMX-Splitter cum Booster 6 - Port Splitter Cum Booster 6 output DMX Splitter & Booster works as DMX signal amplifier and signal splitter. The signal amplification/boosting function should amplify the DMX master controller’s output DMX signal up to 200 meters by using an ideal DMX cable. The DMX Splitter & Amplifier’s all six output terminals are optically isolated. All six outputs should have an independent output 9V coil transformer to boost the DMX signal. The Splitter/booster should be capable of working on 220V/230V line voltage AC. Operating temperature shall be -10 to 50 Deg Celsius. Protection Rating IP 20. Splitter/Booster should be equipped with included mounting brackets which allow multiple installation options for rack, floor, surface, ceiling mounting .3 pin XLR Connectors for IN and OUT connections for firm and solid connection for DMX signal. The signal strength of DMX signal should be above 4 V at each output for reliable signal strength for a maximum of 20 lights in a chain and to 200 meters maximum length to the last light. Equipped with an accessible fuse carrier and supplied with 1.5sq. mm 3 core cable pre-connected. The system shall be housed in a suitable equipment rack having adequate cooling and powering option. Luminaire Type : Signal Splitter

FACADE LIGHTING BOQ FOR OLD CORPORATION OFFICE

18W (RGBW) - floodlight/ accent effect Supply of RGBW Surface mounted Wide beamRound Projector luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10W to 240Wat steady state full intensity. Luminaire should be able to run on AC/ DC Voltage. Power factor of the luminaire shall be -more than 0.90.Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenanceL70@ 25 °Cof the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Die cast Aluminiumwith3-4mm thick safety glass. impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.LEDsof CREE / LUMILED / OSRAM / NICHIA/BRIDGELUX / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Square projector

18W (RGBW) -1000mm Wall Washer/ Wall Grazing Luminaire Supply of RGBW Wide beamLinear Wall Washer luminaires suitable for outdoor applications of Facade Lighting. Luminaires should be enabled with high power LEDs, should consists of highly efficient, UV and temperature-resistant optics with symmetric distribution with glass cover. Power consumption should be between 10w to 96W at steady state full intensity. Luminaire should be able to run on DC Voltage. Power factor of the luminaire shall be more than 0.90. Luminaire should be provided with suitable integral/separate non-integral power supply unit. The lumen maintenance L70@ 25 °C of the LED shall not be less than 70% of the initial lumen after 50,000 burning hours. Ingress Protection should be IP66or higher. Housing should be made of Extruded Aluminium with 3-4mm thick safety glass. Impact resistance level should be suitable to site condition IK07 or better. Adequate heat sink with proper thermal management shall be provided. Operating Temperature : -10°C to +50°C, Operating Humidity : 10% -90%, Housing to have adjustable base bracket for angle adjustment so that the light direction can be adjusted to illuminate desired structural elements.LEDs of CREE / LUMILED / OSRAM / NICHIA/ / PHILIPS shall be used for the light fittings. (Mention the LED beam angle in the spec). Luminaire Type : Linear wall washer

DMX-512 Controller DMX Controller DMX Controller - Stand Alone Interface with a combination of internal memory and micro SD card with connector blocks and DIN RAIL mountable. Controller should be capable of handling 1024 DMX channels extendable to 2048 channels with a simple firmware update. Programming the controller and saving the scenes, memories, triggers, and various integration settings from PC/Laptop running Windows, MAC OS or Linux. Programming should be possible over USB , LAN and remotely over INTERNET. The controller should be capable of assigning scene/program triggers with RS232, UDP / DMX IN, Real Time Clock, and calendar, 12direct and 31multiplex programmable dry contacts (On, On/Off, Release, Restart, Scene Priority, UP/DOWN etc..). A maximum of 2500 scenes across 5 different zones capacity. Input power voltage: 5~24V DC with USB C cable included and equipped with an additional connector block input. The controller should have DMX to adopt to various types of projects and Lighting configurations.(storage size of the internal memory/SD card to be mention. Also the system shall be powered through a suitable capacity Online UPS with min back up.) The system shall be housed in a suitibale equipment rack having adequate cooling and powering option. Luminaire Type : DMX-512 Controller

4- Port DMX-Splitter cum Booster 4 - Port Splitter Cum Booster 4 output DMX Splitter & Booster works as DMX signal amplifier and signal splitter. The signal amplification/boosting function should amplify the DMX master controller’s output DMX signal up to 200 meters by using an ideal DMX cable. The DMX Splitter & Amplifier’s all six output terminals are optically isolated. All six outputs should have an independent output 9V coil transformer to boost the DMX signal. The Splitter/booster should be capable of working on 220V/230V line voltage AC. Operating temperature shall be -10 to 50 Deg Celsius. Protection Rating IP 20. Splitter/Booster should be equipped with included mounting brackets which allow multiple installation options for rack, floor, surface, ceiling mounting .3 pin XLR Connectors for IN and OUT connections for firm and solid connection for DMX signal. The signal strength of DMX signal should be above 4 V at each output for reliable signal strength for a maximum of 20 lights in a chain and to 200 meters maximum length to the last light. Equipped with an accessible fuse carrier and supplied with 1.5sq. mm 3 core cable pre-connected. The system shall be housed in a suitibale equipment rack having adequate cooling and powering option. Luminaire Type : Signal Splitter

AMC

4th year

5th year

6th year