Kerala State Cooperative Bank Tender

DOUBLE SKIN SOLID PLYWOOD PARTITIONS: Providing & fixing plywood Partition system(80mm) for bank area as per architect approved drawing. Partition to be fixed for a height of 270 cm Frame work to be finished with 19mm thick plywood( IS 710 Grade, BWP,). Both sides of the frame to be fixed with 9 mm thick ply( IS 710 Grade, BWP , ).Finish both side of the partition with 0.8mm thick laminate sheet (Greenlam HSC).Finish the partition with necessary grooves, electrical/Window openings if any. Including cost and conveyance of all materials labour charges etc. complete as per drawing.Only visible areas will be measured.

GLAZING TYPE TOUGHNED GLASS ENTRANCE DOOR FOR CABINS Supply and fixing of single leaf frameless entrance door (90x210). 12 mm toughened glass of approved make (Saint Gobain)to be fixed with as per architects design. 12” Stainless steel door handle (Ebco/Hettich) of approved make to be fixed on the door. Heavy duty floor spring (90kg), top and bottom patches of approved make (Ebco/Hettich) to be fixed along with other necessary hardwares not limited to door stopper, locks etc. Rate to be inclusive of transportation, labour etc. Work to be finished as per architect’s satisfaction

GLAZING TYPE TOUGHNED GLASS DOUBLE SHUTTER DOOR FOR MAIN ENTRANCE Supply and fixing of frameless double leaf entrance door (75x210x2nos). 12 mm toughened glass of approved make (Saint Gobain)to be fixed with etching as per architects design. 12” Stainless steel door handle of approved make (Ebco/Hettich) to be fixed on the both door. Heavy duty floor spring (90kg), top and bottom patches of approved make (ebco/Hettich)to be fixed along with other necessary hardwares not limited to door stopper, locks etc on both doors. Rate to be inclusive of transportation, labour etc. Work to be finished as per architect’s satisfaction

PLYWOOD FLUSH DOOR WITH LAMINATE FINISH: Providing and fixing flush door with frame, Door shutter frame finished using 19 mm thick Plywood (IS 710 grade, ) & finished with 0.8 mm laminate (Greenlam HSC). Door shutter made of 19mm thick plywood/door ply, both sides finished with 9mm thick plywood, both sides of the shutter to be finished using 0.8 mm thick laminate using Suitable Adhesive. Complete the door with necessary accessories( SS Hinges, 8” double sided SS handle, Concealed lock, Auto Closer , Tower bolt etc.).Including all cost and conveyance of materials, labour etc. complete. Size 90x210.

OFFICER COUNTER FOR BANK AREA : Providing & placing Workstation Table (75 cm wide, 75 cm high) as per architect approved drawing. Frame Work to be finished with 19 mm thick Plywood ( IS 710 Grade, BWP ,).All outer portion of the table to be finished with 0.8 mm laminate Sheet (Greenlam HSC) as per drawing. Inner portion of the table to be finished with 0.7 mm laminate Sheet(Greenlam/Equivalent) as shown in the drawing.Finish the table with Keyboard Tray, CPU provision , 2 shelf, 2 drawer, and Footrest. Hardware & Fittings : Hettich/Ebco/Equivalent. Finish as per drawing with necessary grooves, projections & electrical openings if any. Including cost and conveyance of all materials labour charges etc. Only front side top edge will be measured Size 150x75x75 cm

CASH COUNTER TABLE WITH CUSTOMER PLATFORM :Providing & fixing cash counter Table as per design intent. Frame Work to be finished with 19 mm thick Plywood ( IS 710 Grade, BWP). All outer portion of the table to be finished with 0.8 mm laminate Sheet (Greenlam HSC) as per drawing. Inner portion of the table to be finished with 0.7 mm laminate (Greenlam /Equivalent) . Finish the main table with Foot rest(Hard wood) ,CPU Provision ,key board tray, drawers and shelf. Additional elevated table top provision to be provided separately for customer transaction area as well as staff area.Use necessary SS hinges , locks, Telescopic sliders, SS handles etc (Make: Hettich\Ebco\equivalent). Finish as per drawing with necessary grooves, projections & electrical openings if any. Including cost and conveyance of all materials labour charges etc. Only front side top edge will be measured Size 150x75x120 cm

FULL HEIGHT SLIDING DOOR STORAGE WITH LAMINATE FINISH : Providing & fixing storage as per architect approved drawing. Storage to be finished with 19 mm thick Plywood ( IS 710 Grade, BWP ,) &6 mm ply to be fixed on back side of storage ( IS 710 Grade, BWP ,) . Outer portion of the storage to be finished with 0.8 mm Laminate sheet (Greenlam HSC) as per drawing. Inner portion of the storage to be finished with 0.7 mmlaminate Sheet(Greenlam/Equivalent).Back side of the storage to be finished with one coat Primer. Full height sliding door with 20 mm block board to be provided for the storages. Use necessary SS hinges, SS handles, Locks, etc(Make: Hettich/Ebco).Finish as per drawing with necessary grooves, projections & electrical openings if any. Including cost and conveyance of all materials labour charges etc. Width of storage will be 43cm.

WALL AND PILLAR PANELLING: Providing & fixing Wall panelling and pillar panelling , height 270 cm, as per architect approved drawing. Frame work to be finished using 19 mm ply ( IS 710 Grade, BWP ,). 9 mm ( IS 710 Grade, BWP ,) ply to be fixed over the frame work. Finish the exterior part of the panelling using 0.8 mm thick laminate(Greenlam HSC) as per the pattern shown in the drawing. Finish the panelling with necessary projections, grooves, electrical/Window openings if any. Including cost and conveyance of all materials labour charges etc. complete as per drawing. Only visible areas will be measured

GYPSUM FALSE CEILING: Providing and fixing gypsum suspended ceiling, which includes Gyproc surface ribbed perimeter channels (having one flange of 20mm and another flange of 30mm and a web of 27mm) along the perimeter of ceiling, screw fixed to wall/partition with the help of nylon sleeves and screws, at 610mm centers. The suspending G.I intermediate channels of size 45mm, at every 610mm c/c. Ceiling sections of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to intermediate channel with the help of connecting clip and in direction perpendicular to the intermediate channel at 610mm centres. 12mm mm tapered edge Gypsum is then screw fixed to ceiling section with 25mm drywall screws driver or drilling machine with suitable attachment (All G.I channels are Saint-Gobain Gyproc). The 12mm thick saint gobain boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edge of the boards with jointing compound & joint paper tape. Rate shall be inclusive of Cut outs for A/c machines, spot lights, light fixtures, A/C. Grills, fire and security systems cut outs, All Sections should adhere to the manufacturers guidelines. Including cost and conveyance of all materials labour charges etc. complete as per drawing.

10MM THICK MILKY WHITE GLASS FOR COUNTER TABLES: Supplying and fixing of 10 mm thick milky white e top on top of tables. There should not be joints on individual table tops. All the edges have to be neatly moulded as per the the length of the table. Edges to be moulded tidily as per architects satisfaction. Only visible area to be measured Rate to be inclusive of cutting charges, molding charges, tapering charges, wastage, transportation, labour etc.Only visible area to be measured

SIDE TABLES WITH STORAGES FOR COUNTER: Providing and placing side tables made of 19 mm ply ( IS 710 Grade, BWP ) and finished with 1 mm laminate. 4 shelves of 19mm thick board to be placed below. 10 mm thick float glass (approved make) to be placed on top. All necessary hardware like hinges, screws, multipurpose locks, stoppers, drawer slides, ball catchers to be provided. All inside surfaces should be laminated with approved laminate. Size( 60x40x60cm). Rate to be inclusive of transportation, labour etc. Work to be finished as per architect’s satisfaction.

ZEBRA ROLLER BLINDS. Applying Luxes 100 mm roller blinds using imported single stem runner, operating chain, link chain and USA pat P32564control unit. The handrail must be powder coated slim line aluminium, a 3 way shiftiness to roll 360 degrees and moving. The fabric must be water and oil repellent. The bottom shall be weight galvanized. Approx rate Rs.180/Sqft DESIGN: As per architect choice

Plastic Emulsion Paint Application Applying two or more coats of plastic emulsion paint of approved make over a coat of primer on walls and ceiling. The work includes sand papering, applying of 2 coats of wall putty of Birla make/equivalent to give even and smooth finish as per directions of the bank. Rate includes cost and conveyance of all materials, labour etc.

ELECTRIFICATION

Supply, design and locating of 18mm/20mm/25mm junction boxes ISI slandered (precession) 1/2/3/4 ways normal/deep size as to give ceiling connections and drawing circuits through 20 mm size of pvc pipe–ISI standard (GEO., PRESESSION, CONSEAL) and inter connecting the JB`s circuit separately and for ceiling terminations. Including cost and conveyance of all materials labour charges etc. complete.

Lights points:-Supply and fixing light/fan points on ceiling and walls or where ever designed by electrical engineers with (ISI std) feruled as per standard and with specific amperage modular switch control including cost and conveyance of all materials labour etc complete.

One light point controlled with one switch

Two light points controlled with one switch

Three light points controlled with one switch for nameboard

LIGHT FITTINGS:-

Supply and fixing of SQUARE/ROUND -12 W LED lights on celling where ever designed by electrical engineers with copper coloured wire with green earth wire so as to share the connected load and equal distribution of lights bands for standard candle power and keeping distance. including cost and conveyance of all materials labour charge etc . complete

Supply and fixing of LED 7 w lights 3 BALLS on ceiling or wall where ever designed by electrical engineers with copper coloured wire with green earth wire so as to share the connected load and equal distribution of lights bands for standard candle power and keeping distance including cost of material and labour charges etc. complete

Supply and fixing of 20W LED Tube set and other fittings. Including cost and conveyance of all materials labour charge etc. complete

Locating and installing additional points from the voltage stabilizer generator set and inverter as per the design and connected load sharing as possible with its change over switch including cost and conveyance of all materials labour charge etc. complete

Locating and fixing ceiling/ wall fan points with colour wire earth continuity nearby the existing fan clamps on ceiling or wall fan location where ever needed with stepped regulator for system for speed control excluding installation of fans with one way switch including cost and conveyance of all materials labour charge etc . complete

Supply and installing of 300mm wall fan neatly and safely or fixing with anchor fastener and making good the all after fitting etc complete. including cost and conveyance of all materials labour charges etc. complete

Drawing special lines for telephone point up to 5 pair where ever designed by the Electrical Engineer and Installing the independent specific sockets (jack) including cost and conveyance of all materials labour charges etc. complete

Drawing special Line for Ian cabling point up to 5 pair where ever designed by the Electrical Engineer

Supply and Installing 3 pin 6A plug point with 14 swg bare copper or with 1.5 mm green wire earthing combined with the existing switch board and with a separate switch control etc. complete each nos including cost and conveyance of all materials labour charges etc. complete

Locating and installing of 16A- 3 pin power plug with indepented SB (3 x 2.5mm,4,6 wire), green wire for earthing up to 5mtr distance from the control panel / DB including cost of all materials labour charges etc. complete

Locating and installing of 20 A- 3 pin power plug with DP switch for AC points including cost of all materials labour charges etc. complete

Locating and installing of switch boards with base plate, cover etc of approved make including cost of all materials labour charges etc. complete

8 MD

12 MD

16 MD

Design and drawing circuit colour code wire 1 mm 650v grade with independent MCB control crimpling feruling etc If necessary as per the Electrical Design up to a distance 10 m from DB/control panel .including cost and conveyance of all materials labour charges etc .complete

Design and drawing circuit colour code wire 1.5 mm 650v grade with independent MCB control crimpling feruling etc If necessary as per the Electrical Design up to a distance 10 m from DB/control panel .including cost and conveyance of all materials labour charges etc .complete

Design and drawing circuit colour code wire 2.5 mm 650v grade with independent MCB control crimpling feruling etc If necessary as per the Electrical Design up to a distance 10 m from DB/control panel .including cost and conveyance of all materials labour charges etc .complete

Design and drawing circuit line colour code wire 4 mm 650v grade with Independent MCB control crimpling feruling etc If necessary as per the Electrical Design up to a distance 10 m from DB/control panel .including cost and conveyance of all materials labour charge complete

Design and drawing circuit line colour code wire 6 mm 650v grade with Independent MCB control crimpling feruling etc If necessary as per the Electrical Design up to a distance 10 m from DB/control panel .including cost and conveyance of all materials labour charge complete

Installing 4 pole ELCB of breaking capacity 30mA and current rating @ 400c: 16 100A and giving connection termination in colour code of specific wire and earthing the same with testing and commissioning etc. including cost and conveyance of all material, labour etc

INSTALLING ISLOATORS of breaking capacity 16/32 A and giving connections/ termination in colour code of specific wire and earthing then same with testing and commissioning etc including cost conveyance of all materials labour charge etc complete

16A 2 POLE

32A 4 POLE

6A-32A SP MCB

Design locating and installing of specific amperage double door distribution boxes with MCB and other all necessary fittings dressing the wires /cables neatly as per colour code and giving connection to the insulators ELCB/MCB/neutral linking/earth link/pilot lamps/including cost and conveyance materials labour charge etc complete.

3 phase 8way light db

Inverter/ups 1 phase 12way db

Supplying and laying telephone cabling using 2 pair fusible cable for linking all tables as per interior design including cost conveyance of all materials labour charge etc complete

Liasoning charges for the approval of KSEB/Inspectorate including the submission of required drawings, for obtaining necessary approvals including incidental and handling charges. Statutory fees to be paid by the bank, if any