Kerala Small Industries Development Corporation Limited Tender

Providing and fixing partition up to ceilingOD : Gypsum Board Partition :height (upto 360cm) consisting of G.I.frame and required board, including providing and fixing of frame work made ofspecial section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/(both side inclusive), consisting of floor and ceiling channel 50 mm wide having equalflanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length orsuitable anchor fastener or metal screws with nylon plugs and the studs 48 mm widehaving one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixedvertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along bothends of partition fixed flush to wall with suitable anchor fastener or metal screws withnylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both sideof frame work by 25 mm long dry wall screws on studs, floor and ceiling channels atthe spacing of 300 mm centre to centre. The boards are to be fixed to the framework with joints staggered to avoid through cracks, M.S. fixing channel of 99 mmwidth (0.9 mm thick having two flanges of 9.5 mm each) to be provided at thehorizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointingcompound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), jointfinisher and two coats of primer suitable for board as per manufacture’s specificationand direction of engineer in charge all complete.75 mm overall thickness partitionwith 12.5 mm thick Moisture Resistant Board

10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.)trussesetc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.80 Providing and applying white cement based putty of average thickness 1 mm,of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

NDSR: Linear Workstations :Fabrication, Supply & Installation work stationWith eachindividual unit as per the drawing. 18mm marine IS 710 Grade plywood with 1mmlaminate (Greenlam) finish on both side with 2 mm PVC edge band. Necessary wiremanagement with approved material and front separation above the table top, at750mm high from floor with necessary vertical support of aluminium leg frames withepoxy powder coating with necessary plinth screw bushes at the base. 300mmacrylic partition on table top with holder at the base. Including cost and conveyanceof all materials labour charges etc Size : 1200 L x 600 W X 750 H mm

NDSR: Pedestal storage : Fabrication supply and installation of side storage as per the size with 16mm marine IS 710 Grade plywood both side 1 mm laminated (Greenlam) finish with three soft closing drawers and profile handle . All edges are lipped with 2mm and 0.8mm PVC edge band. Bottom shall be provided with castor for mobility. Hardware: Ebco. All pieces will be joined using boring. 600x450x640 mm (beneath Table).Including cost and conveyance of all materials labour charges etc

Mid back Chair: Supplying and placing mid back chair (Make: BosQ/Godrej/Minister/ Desqoo Equivalent) as per design intent. Provide Mesh back, knee tilt and adjustable armrest complete as per manufacture specification including all cost and conveyance of materials, labour etc complete.

Meeting room table : Size : 3000 L X 1000 W X 750 H mmTable top 18mm marine IS 710 Grade plywood with 1mm laminate (Greenlam) finish on both side. .Understructure : Necessary wire managent so that switches to be mounted on wire traybelow table top and acccesed using soft closing access flap ( atleast 2 openings ) ,Accessories (excluding switch and socket). Leg : Central supports with MS powder coated leg and beams.