Kerala Small Industries Development Corporation Limited Tender

NDSR : Gypsum Board Partition : Providing and fixing partition up to ceiling height (upto 360cm) consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm

NDSR: Modified 10.16.1 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with

NDSR: Design, printing and installation of graphics onwall with Digitally reproduced art work printed on self adhesive vinyl film and installed over existing surface of partition/panelling as per details.

NDSR: Providing and fixing window blinds - sheer blinds

11.41.3 : Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 800x 800 mm

NDSR: Floor Carpet :Providing and laying synthetic carpet tile Rosetta or equivalent made of 100%PP and not less than 500 gsm pile weight. The carpet shall be fire retardant and stain proof. The total thickness of carpet sheet shall not be less than 7 mm and completely waterproof resilient backing. The fixing on floor shall be done with suitable glue as per manufacturer's specification.

NDSR :3 seater sofa : Fabricating, supply and fixing of 3 seater sofa set using inside 9 mm plywood with treated wood , seating area above 40 density rebounded foam and 32 density sofat foam, other area 23 density hd foam and art leather or cloth fabric cost-450/mtr

NDSR: Center table for sofa seater : Fabrication, Supply & Installation table as per the drawing 15mm MDF with 0.8 mm laminate (Greenlam or equivalent) finish on both side. approved material and 550 mm hight from floor with necessary vertical support of MS leg frames with epoxy powder coating with necessary plinth screw bushes at the base. Including cost and conveyance of all materials labour charges etc Size 750x750 mm

NDSR: Linear Workstations : Size 1200 L x 600 W X 750 H mm, Table top 25 mm tk particle board in E1 grade finish with 2 mm PVC edge band. Under structure : Necessary wire managent so that switches to be mounted on wire tray below work top and acccesed using soft closing access flap, Accessories (excluding switch and socket) , Leg : Aluminium extruded powder coated leg and MS powder coated edge beams. Front separation above the table top, 300mm height acrylic screen partition on table top with neccessary partition holder at the base

NDSR: Pedestal storage : Fabrication, supply and installation of side storage as per the size with prelaminate board with one drawer, 2 shutter opening and profile handle . All edges are lipped with 2mm and 0.8mm PVC edge band. Bottom shall be provided with castor for mobility. Hardware: Ebco auto closing type. 600x450x640 mm (beneath Table).Including cost and conveyance of all materials labour charges etc

NDSR : Dismantling, shifting and refixing the work station tables, conference table, manager table and chairs from the existing incubation space to new space

Appendix 2 : Electrical Item code - 1.55 -Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. GROUP A

Group B

Group C

Item code.1.7.1 - Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required 2x1.5 sq.mm + 1x1.5 sq.mm earth wire

Item code 1.7.2-Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Item code - 1.24.1 - Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch

Item code - 1.24.4- Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet

Item code - 1.24.3-Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amps switch

1.24.5 Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet

2.10.1 Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

2.17 Supplying and fixing TP sheet steel enclosure on surface/ recess along with 16/25/32amps 415 volts "C" curve TP MCB complete with connections, testing and commissioning etc. as required.

90.11.1.12 Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 8 way (8+24) - three phase double cover (IP 42/43)

7.7.1 Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

MR807 10 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

MR808 16 sqmm 4 core PVC/XLPE insulated armoured cable with aluminium conductors for working voltages up to and including 1100 volts conforming IS 1584/part I/1988 for PVC IS 7098 part I for XLPE

Supplying and fixing following size/ modules, alongwith modular base & cover plate for modular switches in recess etc. as required with PVC box -6 module

Item code 5.2-Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

90.16.1.10 - Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required 3.15 mm copper conductor ( 10 SWG)

5.40-Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Supplying and fixing following rating, double pole, (single phase and neutral), 415 V, Residual Current Circuit Breaker with Overcurrent protection (RCBO), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 A rating, 4 pole RCBO, 30mA

Supplying and fixing following rating, double pole, (single phase and neutral), 415 V, Residual Current Circuit Breaker with Overcurrent protection (RCBO), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40A rating, 4 pole RCBO, 30mA

Item code: 1.21 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required Item code: 1.21.1 20mm

Item code: 1.21.2 25mm

Appendix 3 : IT & Network Router IP and IP services ● Routing Protocols: RIPv1, RIPv2, OSPF, EIGRP, BGP, IS-IS ● Generic routing encapsulation (GRE) and multipoint GRE (mGRE) ● Cisco Express Forwarding ● Standard 802.1d Spanning Tree Protocol ● Layer 2 Tunneling Protocol (L2TP, L2TPv3) ● Network Address Translation (NAT) ● Dynamic Host Configuration Protocol (DHCP) server, relay, and client ● Dynamic Domain Name System (DNS), DNS Proxy, DNS Spoofing ● Access control lists (ACLs) ● IPv4 and IPv6 Multicast ● Performance Routing (PfR) ● Virtual Route Forwarding (VRF) Lite ● Next Hop Resolution Protocol (NHRP) ● Bidirectional Forwarding Detection (BFD) ● Web Cache Communication Protocol (WCCP) ● Flexible NetFlow (FNF) ◦ PPP ◦ HDLC ◦ PPPoE LAN ● 16 802.1Q VLANs ● MAC filtering ● Switched Port Analyzer (SPAN) ● Storm Control ● Internet Group Management Protocol Version 3 (IGMPv3) snooping ● 802.1x Security ● IPsec with IKEv1& IKEv2, IPsec over IPV6, VRF-aware IPsec ● EasyVPN, DMVPN, Tunnel-less Group Encrypted Transport VPN, Secure Socket Layer (SSL) VPN

10/100/1000 Mbps 24 Port Manageable Switch with limited life tim General Details 24 10/100/1000 ports 4 Gigabit SFP Rack-mountable 56Gbps Switching capacity Capacity in Millions of Packets per Second above 40 Switching Capacity in Gigabits per Second (Gbps) above 55 Spanning Tree Protocol Standard 802.1d Spanning Tree support VLAN 4,094 VLANs simultaneously VLAN Translation Must support One-to-One Mapping Dynamic Host Configuration Protocol DHCP traffic to DHCP server in different VLAN, with option 82 IPv4 routing Up to 990 static routes and up to 128 IP interfaces DHCP Server Switch functions as an IPv4 DHCP server serving IP addresses for Security Must have features such as SSH, SSL, IEEE 802.1X (Authenticator), 802.1X supplicant, Web-based authentication, STP, DHCP snooping RADIUS/TACACS+ Supports RADIUS and TACACS authenticatio Rate limiting Ingress policer; egress shaping and rate control; per VLAN, per por based; 2R3C policing EEE Compliant (802.3az) Supports IEEE 802.3az on all copper Giga Buttons Reset button Cabling type Unshielded Twisted Pair (UTP) Category 5e or better Flash 256 MB CPU 800 MHz ARM DRAM 512 MB

10/100/1000 Mbps 8 Port Manageable Switch Poe with limited life

Cat-6 UTP Cable Blue Color - with casing and capping and crimpin a) The 4 pair Unshielded Twisted Pair cable shall be FR-PVC b) This cable well exceeds the requirements of TIA/EIA-568-C.2 an c) Nominal Outer Diameter of Cable should be 5.7+/-0.01mm min a d) Construction: 4 twisted pairs separated by internal PE Cross Sep e) Conductor Solid bare Copper and Outer jacket sheath FRPVC an f) Insulation :High Density Polyethylene Solid g) Dielectric Strength of cable should be 1000 V RMS h) Bending Radius : 4X Cable Diameter at -20°C +/- 1°C , Pulling i) Electrical Parameters Pair – to – pair and PS NEXT, ELFEXT and j) Insertion Loss of 32.8 db/100m at 250 MHz k) Cable should support operating Temperature from -20° to +70°C l) Cable support Conductor Resistance 9.38 Ω /100m m) Mutual Capacitance of cable should be 5.6nF/100m n) Max Resistance Unbalance of cable should be 5% Max o) Capacitance Unbalance of cable should max 330pF/100m p) Cable support Delay Skew: 45nS, Operating Voltage: 72V NVP q) Printed sequential Length Counter of each meter on Outer Jacket r) Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base s) Category 6 UTP cables FR-PVC/LSZH should be 250 MHz

Cat-6 UTP Cable Yellow Color - with casing and capping and crimp a) The 4 pair Unshielded Twisted Pair cable shall be FR-PVC b) This cable well exceeds the requirements of TIA/EIA-568-C.2 an c) Nominal Outer Diameter of Cable should be 5.7+/-0.01mm min a d) Construction: 4 twisted pairs separated by internal PE Cross Sep e) Conductor Solid bare Copper and Outer jacket sheath FRPVC an f) Insulation :High Density Polyethylene Solid g) Dielectric Strength of cable should be 1000 V RMS h) Bending Radius : 4X Cable Diameter at -20°C +/- 1°C , Pulling i) Electrical Parameters Pair – to – pair and PS NEXT, ELFEXT and j) Insertion Loss of 32.8 db/100m at 250 MHz k) Cable should support operating Temperature from -20° to +70°C l) Cable support Conductor Resistance 9.38 Ω /100m m) Mutual Capacitance of cable should be 5.6nF/100m n) Max Resistance Unbalance of cable should be 5% Max o) Capacitance Unbalance of cable should max 330pF/100m p) Cable support Delay Skew: 45nS, Operating Voltage: 72V NVP q) Printed sequential Length Counter of each meter on Outer Jacket r) Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base s) Category 6 UTP cables FR-PVC/LSZH should be 250 MHz

Cat-6 UTP Cable Orange Color - with casing and capping and crimping with labour charge : Used for Access control system a) The 4 pair Unshielded Twisted Pair cable shall be FR-PVC b) This cable well exceeds the requirements of TIA/EIA-568-C.2 and ISO/IEC 11801 c) Nominal Outer Diameter of Cable should be 5.7+/-0.01mm min and Conductor Diameter 24 AWG d) Construction: 4 twisted pairs separated by internal PE Cross Separator. Full separator. Half shall not be accepted. Rip Cord is must. e) Conductor Solid bare Copper and Outer jacket sheath FRPVC and CM rated cable. Jacket color: Grey f) Insulation :High Density Polyethylene Solid g) Dielectric Strength of cable should be 1000 V RMS h) Bending Radius : 4X Cable Diameter at -20°C +/- 1°C , Pulling Force: 25.35 LBS i) Electrical Parameters Pair – to – pair and PS NEXT, ELFEXT and PSELFEXT, Return Loss, ACR and PS ACR. j) Insertion Loss of 32.8 db/100m at 250 MHz k) Cable should support operating Temperature from -20° to +70°C l) Cable support Conductor Resistance 9.38 Ω /100m m) Mutual Capacitance of cable should be 5.6nF/100m n) Max Resistance Unbalance of cable should be 5% Max o) Capacitance Unbalance of cable should max 330pF/100m p) Cable support Delay Skew: 45nS, Operating Voltage: 72V NVP: 69% and Current Rating : MAX 1.5A q) Printed sequential Length Counter of each meter on Outer Jacket r) Category 6 UTP cables shall Supports Gigabit Ethernet (1000 base-T) standard and Operates at bandwidth of 600MHz s) Category 6 UTP cables FR-PVC/LSZH should be 250 MHz

Cat-6 Keystone Jack a) Category 6 Keystone jack should be suitable For 23~24 AWG Stranded and Solid Wire, Easy For Termination and Compliant to T568A and T568B Wiring Schemes b) Compatible with Both 110 & Krone Punch Down Tool. c) RJ45 8P 8C 50u Jacks d) Fast, Easy, Reliable Termination e) Should Fit in High Density Keystone Patch Panel And on Face Plates f) Keystone Jack Can Be Easily Terminated by punch down tool g) Backward compatible with both RJ11/RJ12 Plug h) Physical: Housing : High impact flame retardant plastic, UL 94V-0 rated PCB : FR-4 T=1.6mmThickness Contact Material : Phosphor Bronze Stamp Pin T=0.35mm IDC Contact Material : Phosphor Bronze T=0.50mm With Tin Plating Gold Plating : 50 microns Connector : Insulation displacement connector IDC to support Wire : AWG 22~24 i) Electrical: Current Rating : 1.5amps Insulation Resistance : 500 MΩ minimum Contact Resistance : 10 mΩ maximum DC Resistance : 0.1 Ω maximum j) Mechanical: Plug Insertion Life : 750 Cycles minimum Plug & Jack Contact Force :100 Grams minimum using FCC-approved plug Plug Retention Force : 30 lbs minimum Temperature : -40° to 150°F (-40° to 68°C) k) Standard Verification: Qualified unscreened Class E/Cat.6 Permanent Link & Channel ANSI/TIA-568-C.2 IEC 60603-7-4 2nd Edition ISO/IEC 11801 2.2 Edition

RJ11 Keystone

Face Plate Single a) British style Square Face Plate (86 x 86mm) b) Shutter on Face Plate c) Elegant : hidden-screw design d) Glossy Finish : Suite for all decor e) MATERIAL: ABS 765 UL94V-0 f) Plug Retention Force : 14Kgf (140N) g) Plug Reliability : 750 Cycles minimum h) Should support UTP and STP Jacks Cat5e, Cat6 and Cat6A i) Standard Verification: ANSI/TIA-568-C.2 ISO/IEC 11801:2002 AMMD.2:2010 YD/T 926.3-2009 ISO/IEC 60603-7 Compliant RoHS Directive 2002/95/EC/Compliant

Face Plate Dual a) British style Square Face Plate (86 x 86mm) b) Shutter on Face Plate c) Elegant : hidden-screw design d) Glossy Finish : Suite for all decor e) MATERIAL: ABS 765 UL94V-0 f) Plug Retention Force : 14Kgf (140N) g) Plug Reliability : 750 Cycles minimum h) Should support UTP and STP Jacks Cat5e, Cat6 and Cat6A i) Standard Verification: ANSI/TIA-568-C.2 ISO/IEC 11801:2002 AMMD.2:2010 YD/T 926.3-2009 ISO/IEC 60603-7 Compliant RoHS Directive 2002/95/EC/Compliant

Back Box (Network) a) Should have Robust and installer friendly design Surface MountBoxes for Face Plates for a variety of media including voice and data, Audio, video and CATV distribution to the work area. b) Should secure and protect wire with durable wall box c) Material : ABS d) Shape : SquareSize : 86 x 86 e) Color : White

Back Box (Camera) a) Should have Robust and installer friendly design Surface MountBoxes for Face Plates for a variety of media including voice and data, Audio, video and CATV distribution to the work area. b) Should secure and protect wire with durable wall box c) Material : ABS d) Shape : SquareSize : 86 x 86 e) Color : White

Cat-6 24 Port Patch Panel Loaded a) The Cat-6 transmission performance is in compliance and Exceeds ANSI/TIA/EIA-568-C.2 Standard. Supports 1000-Base-T. b) Modular Design in loaded or individual port design in UnLoaded for Convenient NetworkTerminations c) Built in Rear Cable Management for Ease of Installation. d) Removable Module Design for repair or maintenance. e) 6x4 Module Specially Designed Jack Configuration f) PCB: FR4, 1.6mm Thickness. g) IDC Conductor : 0.5 mm Phosphor Bronze, Tin Plating h) Contact Compatibility : 22~26 AWG Stranded and Solid Wires i) 1U Patch Panel to Mount In any Standard Rack. Panel Frame: SPCC Powder coated black. j) Housing : High Impact Flame Retardant Plastic, UL 94V-0 Rated k) Easy Port Labeling Identification Provision l) Electrical Characteristics: Current Rating : 1.5amps Insulation Resistance : = 500mΩ Contact Resistance : =10mΩ DC Resistance : =0.1Ω DC/AC Volt Endurance : DC 1000V/AC 750V 1 Min m) Mechanical Characteristics: Plug Insertion Life : = 750 Cycles with FCC Compliant RJ-45 Plug Plug & Jack Contact : = 100 Grams with FCC Compliant RJ-45 Plug Force Plug Retention Force : = 11 LBF Durability : 200 Termination Cycles Operating Temperature : -10 Degree ~ 60 Degree Operating Humidity : 10% ~ 90% RH Storage Temperature : -40 Degree ~ 68 Degree n)Standard Verification: ANSI/TIA-568-C.2 ISO/IEC 11801:2002/AMMD.2:2010 YD/T 926.3-2009 ISO/IEC 60603-7 Compliant

Cat 6 1 Mtr Patch Cord Blue a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : Conductor Material : Stranded Copper Conductor Diameter : (24 AWG) Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm Min at any point: 0.17mm MAX AVG:0.19mm Insulation Diameter : 0.94±0.01mm/0.92±0.01mm Cross Filler : Transparent 4.2×0.35 Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm Plug : 50μ’’ Gold Plated Contact Boot : Transparent Standard : ANSI EIA/TIA 568-C.2

Cat 6 1 Mtr Patch Cord Yellow a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assembliesg) Should be Available in Different Colors on requesth) Technical Specifications :Conductor Material : Stranded CopperConductor Diameter : (24 AWG) Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mmMin at any point: 0.17mm MAX AVG:0.19mmInsulation Diameter : 0.94±0.01mm/0.92±0.01mm Cross Filler : Transparent 4.2×0.35Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm Plug : 50μ’’ Gold Plated ContactBoot : TransparentStandard : ANSI EIA/TIA 568-C.2

Cat 6 1 Mtr Patch Cord Gray a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : Conductor Material : Stranded Copper Conductor Diameter : (24 AWG) Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm Min at any point: 0.17mm MAX AVG:0.19mm Insulation Diameter : 0.94±0.01mm/0.92±0.01mm Cross Filler : Transparent 4.2×0.35 Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm Plug : 50μ’’ Gold Plated Contact Boot : Transparent Standard : ANSI EIA/TIA 568-C.2

Cat 6 2 Mtr Patch Cord Gray a) Category 6 UTP Patch Cords should be Factory Tested for Better Quality and Suitable for the High Speed Data Transmission. b) Complies with the ANSI/TIA/EIA-568-C.2 Standard. Supports Data Networks Speeds Up to 10/100-Base-T and 1000-Base-T c) Should be FR-PVC/ LSZH Jacket for Reduced Toxic Gasses Emitted During Combustion d) RJ45, 8P8C, 2 FORK 50μ’’ Gold Plated Contacts e) Patch cords should be 100% Factory Tested f) Transparent Boot Cable Assemblies g) Should be Available in Different Colors on request h) Technical Specifications : Conductor Material : Stranded Copper Conductor Diameter : (24 AWG) Insulation Thickness : Min at any point: 0.18mm MAX AVG:0.20mm Min at any point: 0.17mm MAX AVG:0.19mm Insulation Diameter : 0.94±0.01mm/0.92±0.01mm Cross Filler : Transparent 4.2×0.35 Jacket Type:FR-PVC/LSZH (Low Smoke Zero Halogen) Jacket Thickness : Min at any point: 0.51mm MAX AVG: 0.55mm Jacket Width : Min at any point: 5.2mm MAX AVG:5.8mm Plug : 50μ’’ Gold Plated Contact Boot : Transparent Standard : ANSI EIA/TIA 568-C.2

2 MP IP Survillence Camera - Bullet ● 2MP, HDCVI IR Bullet camera ● 30 fps@1080P 3.6mm fixed lens Max IR length 20 m ● Smart IR IP67 ● DC 12V ● Night vision

8 Channel NVR with 4 TB Survillence HDD Support 8 channel IP camera input Smart H.265+/H.265/Smart H.264+/H.264 codec decoding Up to 8MP resolution preview and playback VGA/HDMI simultaneous video output, maximum resolution of H Motion detection: yes User Interface Web/operating in local GUI

Biometric Access Control device with perpectual license software for attendence tracking (Exit + Entry) Display:7.11cm (2.8) HD Color Display Fingerprint Users:3000 Card User:3000 Password User:3000 Attendance Records:70000 FP Verification Mode:1:1, 1:N Verification:Fingerprint, ID Card, Password Combination:FP/PIN/Card, FP+PIN, FP+Card Verification Time:1.0s False Rejection Rate:0.01% False Acceptance Rate:0.0001% Finger Print Sensor:600dpi Optical Sensor Communication:U Disk, USB, TCP/IP, RFID card,Cloud, Access control Working Humidity: 20%-60% Working Temperature: 0°C-50°C Power Supply:12V DC Battery Backup: Built-in Access Control:Built-in Server Connection:Auto Push Technology

EM Lock Holding Force: 280KG/600lbs Dimension: 250*48*27mm Armature Plate: 180Lx38Wx11H(mm) Voltage: 12/24/48VDC+10% Current: 0.48A/0.24A Operating Temp: -20ºC ~ 60°C Working Mode: Power off to open(NC) Finishes for Shell: Anodized aluminum Finishes for Magnetic:Zinc Finishes for Armature: Zinc

Projector with ceiling mount and projector screen 3,600 Lumens 3LCD technology for equal white & colour light output XGA resolution and 4:3 performance Long lamp life up to 12,000 hours in ECO mode Easy setup and positioning flexibility HDMI connectivity Projection Technology: RGB liquid crystal shutter projection system Interface: USB 2.0 Type B, RS-232C, Wired Network, Wireless LAN VGA in (2x), VGA out, HDMI in, Composite in, Stereo mini jack au audio in (2x), Cinch audio in, USB 2.0 Type A Aspect Ratio:: 4:3 Native Resolution: XGA, 1024 x 768 Fan Noise (Normal / Eco): 37dB / 28dB Colour Light Output: 3,600 Lumen*1- 2,400 Lumen (economy) White Light Output: 3,600 Lumen

Rodent repellant

Chrome Cast Video Resolution: 1080P HDMI: Yes Ports and connectors : HDMI, Micro USB Wireless standards: 802.11 b/g/n/ac Wi-Fi (2.4 GHz/5 GHz) Wireless security: WEP, WPA/WPA2

PC - needed for installing Access control software, survillence softw network management software 1) 15 inch Monitor 2) Keyboard 3) Mouse 4) CPU - i3 latest generation 8 GB ram 256 GB M.2 Mvme ssd Windows 11 Pro Latest MS Office perpectual License

Rack - 12 U with PDU

Cable Manager - 24 Port

Wi-Fi Access point with PoE adapter General Details 2x2 WiFi 6 access point Aggregate throughput upto 1.5Gbps Management interfaces - Ethernet & Bluetooth Ethernet Interface - (1) GbE RJ45 port Management interfaces Ethernet, Bluetooth Button Factory reset WiFi standards 802.11a/b/g, WiFi 4/WiFi 5/WiFi 6 Wireless security WPA-PSK, WPA-Enterprise (WPA/WPA2/WPA VLAN 802.1Q Advanced QoS Per-user rate limiting Throughput rate 2.4 GHz - =300 Mbps 5 GHz - =1201 Mbps Guest traffic isolation Supported