Kerala Khadi And Village Industries Board Tender

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm, with all 4 side tapered ( D S R 2016 12.45.1. )

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: ( D S R 25.7. )

Dismantling Aaluminium / Gypsum Partitions, doors, windows, Fixed glazing and False ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in-charge. ( D S R 15.57 ) Existing ACP Pannelling

Design, fabricating, Testing, installing and fixing in position Curtain wall with Aluminium composite Panel clading on existing Aluminium section base frame work with open groves for linear as well as curvilinear portion of the building for all heights and all levels etc., including scaffolding charge. ( od155072/2024_2025 )

Providing and applying Plaster of paris Putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ( D S R 13.26 )

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer ( D S R 13.43.1 )

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work ( D S R 2018 , 13.52.1 )

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work. ( D S R 13.60.1. )

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. ( D S R 13.61.1 . )

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work ( 2018 D S R 13.98.1 )

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work. ( 2018 D S R, 13.99.1 )

Finishing walls with Acrylic Smooth exterior paint of required shade: Old work (Two or more coats applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface ( 2018 D S R 13.111.1 )

Providing and fixing Aluminium work for Doors, Windows, Ventilators and Partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion - Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) ( D S R 21.1.1.3 )

For Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Polyester powder coated aluminium (minimum thickness of polyester powder coating 50 micron) ( D S R 21.1.2.3 )

Providing and fixing double scaffolding system (cup lock type) on the exterior side, upto seven story hight made with 40 mm dia. M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staricase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required location with essential safety features for the workmen etc. complete as per directions and approval of Engineer- in Charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note:- This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done .( D S R 14.72 )

Providing and fixing Double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness ( D S R 21.4.1. )

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, For all leads including all lifts involved. ( D S R 2018 , 15.60 )

Supplying and Fixing Openable Glass door lock of approved quality and make (EBCO OR EQUIVALENT ) with all necessary accessories etc complete.  od20254/2024_2025

Providing and fixing of 6 mm thick mirror of approved quality , Edge polished with 4 mm thick foam board backing,, fixed to walls, paneling with CP Brass Screws , washers etc complete as directed by the engineer in charge.

10.16.1 Modified , Steel Work in Departmental Built up Tubular ( Round, Square, Rectangular hollow tubes ) trusses etc including cutting hoisting, fixing in position and applying one priming coat of approved steel primer, including welding and bolted with special shaped washers etc complete .

Providing and Fixing 1 mm thick ISI Marked Approved Quality , Color , and Design Laminated Sheets with Texture Finish ( MICA ) on existing surface with good quality Adhesive ( Heatex or Equivalent ) as directed by the Engineer in charge

Modifications and Repairs to Existing Plywood Furniture ( Sales Counters and Cash Counter ) by providing required 12 mm thick IS 303 Grade Plywood with necessary nails, screws, adhesives , including all labor charges , charges for rectification of damages etc complete as directed by the engineer in charge

Providing and fixing 10 mm thick Float Glass Panes as Racks in MS Display Shelves including grinding and polishing the exposed edges etc complete as directed by the Engineer in Charg

Supply and fixing Stainless Steel Cloth Hook of Approved Quality and Size in the Trial rooms with necessary Screws Etc Complete

Providing and fixing Name Board in Existing ACP Surface Using Acrylic LED 3 D Letters using 3 mm Thick exterior grade and heat resistant acrylic sheets ( ISO CERTIFIED ), with 1.50 w HI BRIGHT, SAMSUNG , ADS, BNEZ Water proof L.E.D ( RoHS ), and S M P S 400 W power supplies with 30% extra backup, Branded, weatherproof , with approved brand full copper wiring , including all cost of labor and Scaffolding charges as directed by the engineer in charge

ENGAGING LABOUR FOR MAINTENANCE WORK, CLEANING WORK - BELDAR ( od155103/2024_2025 )

ENGAGING LABOUR FOR MAINTENANCE WORK REPAIR WORKS - FITTER GRADE 2 ( od155104/2024_2025 )

ENGAGING LABOUR FOR DISMANDLING EXISTING ELECTRICAL FITTINGS - ELECTRITION ( od155106/2024_2025 )

ENGAGING LABOUR FOR REPAIR WORK CARPENTER GRADE 1 ( od155107/2024_2025 )

Providing and fixing 8.00 mm thick float glass panes as racks in MS Display Stands and Display Racks including cutting, grinding, and polishing all the exposed edges etc complete as per the Architectural drawings and as directed by the Engineer in Charge ( od155481/2024_2025 )

Providing and fixing M S RACKS and DISPLAY STANDS IN MS Hollow Sections , Steel work in Built up tubular sections ( Round, Square, Rectangular Sections ) including cutting hoisting , fixing in position and applying a priming coat of approved steel primer, Including welding, grinding and bolted with special washers etc complete as per the Architectural Drawing and the direction of Engineer in charge ( od155482/2024_2025 )

Supplying and fixing Modiguard or Equivalent Brand glass Mirror over Frame work of 16 mm BWR Quality IS 303 Grade Play wood frame and covering the rear side with 12 MM BWR plywood and finishing all the exposed surface with 1.00 mm Thickness Decorative Laminated Sheets With Texture Finish of approved brand and shade , Fixing on Wall etc. complete as per the direction of Engineer in charge.

Providing and Fixing plywood Back ground panel made out of FRAME work using 16 mm BWR QUALITY ( IS 303 grade ) plywood at suitable spacing both horizontally and vertically, including making hole in the concrete/ masonry wall, with necessary SS hold fasts or SS screws of necessary size. Then Commercial plywood 12 mm thick B W R grade ( IS 303 Grade ) of approved make is fixed to the Exposed side of the frame work with screws of necessary size , all the exposed surface covered by 1.00 mm thickness Decorative Laminated Sheets with suitable adhesive ( Heatex or Equivalent ) including sealing all the joints and holes all as per the approved drawings and Direction of the Engineer in Charge .

Providing Name Board by Vinyle Sticker Work on Existing ACP PANNEL WORK as per approved Design

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. GROUP B ( D S R ELECTRICAL 1.10.2 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 X 1.5 sq.mm ( D S R ELECTRICAL 1.17.3 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 x 2.5 sq. mm ( D S R ELECTRICAL 1.17.12 )

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required. 3 x 4 sq. mm ( D S R ELECTRICAL 1.17.21 )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 20 MM ( D S R ELECTRICAL 1.21.1 )

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required. 25 MM ( D S R ELECTRICAL 1.21.2 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch ( D S R ELECTRICAL 1.24.1 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch ( D S R ELECTRICAL 1.24.3 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet ( D S R ELECTRICAL 1.24.4 )

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet ( D S R ELECTRICAL 1.24.5 )

Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (RoHS compliant ) 32A DP switch with indicator ( OD 90.10.3.15 )

 Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required. ( D S R ELECTRICAL 1.26 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm) ( D S R ELECTRICAL 1.27.1 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm) ( D S R ELECTRICAL 1.27.2 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required. 6 Module ( D S R ELECTRICAL 1.27.4 )

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.12 Module (200mmX150mm) ( D S R ELECTRICAL 1.27.6 )

 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings). ( D S R ELECTRICAL 1.31 )

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole ( D S R ELECTRICAL 2.10.1 )

Supply, Conveyance , Installation, testing and commissioning of Wall mounting fan of 400 mm Sweep with Oscillation System and Pull Cord, Fixing to wall with wall mounting brackets supplied along with the fan and Giving Connections with Existing wire etc. complete. od28805/2023_2024

Supply Conveyance, installation, testing and commissioning of sleek compact recess mounting LED Slim Panel Light Fitting 18 W, Square or Round, Cool or Warm,size 205 mm or nearest available , with light weight body, energy efficient drive , complete with all accessories , fixing directly on ceiling including giving connections with required length of 3 core round copper conductor flexible wire confirming to the relevant ISS or extending the original wire etc. as required od28806/2023_2024

Supply Installation , testing , Commissioning of Sleek Compact Recess Mounting, LED Slim Panel Light Fitting Square or Round, Cool or Warm, 12 w of size 155 mm or Nearest available size, with Light Weight Body, Energy efficient Drive, with all accessories, fixing directly on ceiling including giving connections with required length of 3 core round copper conductor flexible wire confirming to relevant ISS or extending the original wire etc. as required od28807/2023_2024

Supply Conveyance, Installation, Testing and Commissioning of Sleek Compact Recess Mounting LED Slim Panel Light Fitting 6 w , Square or Round , Cool or Warm, Size 105 mm or nearest available size, with Light weight Body , Energy Efficient Drive,complete with all accessories, fixing directly to the Ceiling including giving connection with required length of 3 core round copper conductor flexible wire confirming to relevant ISS or extending the original wire etc. as required od28808/2023_2024

Supply, Conveyance, Installation, Testing and Commissioning of Sleek , Compact Recess Mounting LED Slim Panel Light Fitting 3W or 4W, Round or Square, Cool or Warm, Size 75 mm or nearest available , with Light weight Body, Energy efficient Drive,complete with all accessories ,fixing directly on ceiling, Giving connections with required length of 3 core copper conductor flexible wire confirming to relevant ISS or extending the original wire etc. as required od28809/2023_2024

Supplying and drawing following sizes of CC TV CABLE in the existing surface / recessed steel/ PVC conduit as required. - 3 +1 CC TV CABLE PURE COPPER OF BRAND D LINK OR EQUIVALENT BRANDS APPROVED BY THE ENGINEER IN CHARGE.

Supply and Fixing and commissioning of 2 MP HD CAMERA HIKVISION ( DS -2CE 16 DOT-ITPFS , 3.6 MM ) with all necessary fittinga and accessories

Dismandling existing AC units at Vanchiyoor KGS , reinstalling and commissioning at new location, including all

Dismantling Existing CC TV System at Vanchiyoor KGS and Installing , Testing and commissioning at New KGS with all necessary fittings as required as directed by the Engineer in Charge

Dismanting , Loading, Convayance, Unloading , and placing of Existing Racks and Counters at Vanchiyoor KGS to New KGS

Providing and Fixing plywood RAISED PLATFORM ( 12 CM ) made out of FRAME work using 16 mm BWR QUALITY ( IS 303 grade ) plywood at 45 CM C/C spacing both ways and fixing the same to floor with necessary SS hold fasts or SS screws of necessary size. Then Commercial plywood 18 mm thick B W R grade ( IS 303 Grade ) of approved make is fixed to cover the frame work with screws of necessary size including sealing all the joints and holes all as per the approved drawings and Direction of the Engineer in Charge .

Providing Texture Work in Wall , Ceiling with approved brand and Design as approved by the Engineer in charge.

Providing and Fixing WALL PAPER OF APPROVED BRAND AND DESIGN as approved by the Engineer in Charge.

Providing and Fixing CARPET FLOORING by with good quality and texture carpet including cost of all materials and labour as per approved Design

Supplying and fixing Photo Print on Acrylic Sheet with LED Lighting Above ACP Wall