Kerala Khadi And Village Industries Board Tender

Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete ( Observed Data Buildings 50.6.2.2. )

12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) ( D S R 2016 13.4.1. )

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead : With cement mortar 1:4 (1 cement : 4 course sand). ( D S R 14.1.2. )

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. ( D S R 13.26 )

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water thinnable cement primer ( D S R 13.43.1 )

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm). ( D S R 13.46.1. )

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work. ( D S R 13.60.1. )

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work. ( D S R 13.61.1 . )

Steel work in built up tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes ( D S R 10.16.1 )

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. ( D S R 12.50 )

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Crimp curve ( D S R 12.51.5. )

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete : Flashings/ Aprons.( Upto 600 mm) ( D S R 12.51.2. )

Dismantling doors, windows and clerestory windows (steel or wood) shutter including Chowkhats, architrave, hold fasts etc complete and stacking within 50 metres lead Of area 3 sq. metres and below ( D S R 15.12.1. )

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness ( D S R 21.4.1. )

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I ( D S R. 12.45.1. )

Providing and fixing TEAK wood frame work consisting of battens 100 x 50 mm For Fixed Glasing fixed with rawl plug and drilling necessary holes for rawl plug etc. including priming coat complete. For Fixed Glased Partitions and Doors

Providing and fixing Glazing in wooden frames using 12 mm Glass of approved brand in Fixed partitions and glazed shutters for doors, (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured).

Supplying and fixing Modiguard or Equivalent Brand glass Mirror over Frame work of Pincoda Wood or Equivalent as approved wood frame and covering the rear side with 12 MM BWR plywood and finishing the teakwood frame with lacquer polish etc. completed as per the direction of Engineer in charge.

Providing and fixing KHADI SHELF ( Horizontal Spacing 90 cm and vertical Spacing 30 / 60 cm ) with stainless steel ( Grade 202 ) Hollow tubes, channels, plates etc., and 8 mm Glass , including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the Shelf to the Wall / Columns with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., Providing 8 mm Glass of of required size, including polishing the exposed edges , all as per the Drawing and approval of the Engineer-in-charge,

Providing and fixing MATTRESS STAND ( SIZE 1.30 M X 1.90 M AND HEIGHT 0 .30 M ) with stainless steel ( Grade 202 ) Hollow tubes, channels, plates etc., and , including welding, grinding, buffing, polishing and making curvature (wherever required) all as per the Drawing and approval of the Engineer-in-charge,

Supplying fabricating and fixing in position sales counter with Granite / Glass top of 60 CM TOP WIDTH AND HEIGHT 80 CM ( AV ) ,made with frames by using PINCODA or similar wood scantling 50x50 mm section framed to form a box, Covered with 16 mm BWR ( IS 303 GRADE ) plywood . for inside rack and top with 12 mm plain glass propped over glass struts over 9 MM plywood with top width 60 to 70cm (av) and front vertical face of the counter being fixed with 16 MM BWR plywood and the vertical face is being sticked with O S T and the outer edge of glass being rounded and polishing , the inside of the counter being painted with synthetic enamel paint 2 coat over one coat of wood primer and putty leveling filling etc. complete as per the approved drawings and direction of the Engineer in charge..

Supplying fabricating and erecting cash cum packing counter of 1 M height (av) with width and length 70 to 90 cm and 2.00 m respectively by using PINCODA or similar wood scantling of size 50x50 mm framed to form a box covered 16 mm B W R plywood round and top with 12 plain glass and the secound hight counter portation providing granite or marble (jet black or galaxy) over 9 mm thick plywood cupboard drawers with locking arrangement foot rest. Space for UPS CPU etc. and the edges of the granite being rounded and the exposed rack faced being painted to coat over a primer coat after applying putty levelling filling etc. complete as per the approved drawings and direction of the Engineer in charge.

Providing and fixing SAREE DISPLAY ( HANGING ) SHELF OF size 1.5 x 0.80 x 1.10 m with stainless steel ( Grade 202 ) Hollow tubes, channels, plates etc., and 12 mm Glass , including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, Providing 12 mm Glass of of required size, including polishing the exposed edges , all as per the Drawing and approval of the Engineer-in-charge,

Supply and fixing Name Board by using ACP fixed over 40mm x40 mm G I sq Tube for outer frame including Sticker Work as directed by the officer in charge

Supplying and fixing Good Quality Stainless Steel Door Handle for Glass Doors of size 45 cm with all necessary screws , nuts etc complete as approved by the Engineer in charge ( MR )

"Disposal of moorum/ building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-Charge. ( D S R 1.1.18 )

APPENDIX-B

Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20mm conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm PVC insulated stranded sing core copper conductor cable 650V grade continuous earthing with No. 14 bare copper, required of copper earth socket, brass bolt and nut crimping/complete including circuit mains to switch board with suitable size modular type metal switch boxes, modular type front plates (white) ete, up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc., complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (Group A modular accessories)Single control light / Wall fan point with 6A 3 plate ceiling rose

Combined plug point with 6A, 5 pin plug socket controlled by 6A switch in the same switch board as that of light points

Do do power plug 16 A 5 pin plug socket

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way piano type switch, phenolic laminated sheet, suitable size MS box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required . ( D S R 1.2 )

Supply &Fixing the following types/sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required

3 module metal box

12 module metal box

Supply &Fixing the following types / sizes of front plates on the existing modular boxes 1 module white

3 module white

12 module white

Supply and Fixing the following modular switches &accessories in the existing front plates and giving necessary connections as required 6 A SP 1 way switch

6 A 2 / 3 pin socket

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.  6 pin 15/16 amp socket outlet ( D S R 1.24.5 )

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required (. DSR 1.26 )

32 A DP Swittch

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories on surface including making good the damages etc as required. 20 mm dia light gauge

Supply and drawing 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface/recess conduit as required including giving necessary connections of the following sizes. 1.00 sq mm 2 run( long light mains 10 point )

1.00 sq mm 4 run( long light mains 10 point )

1.50 sq mm 2 run

1.50 sq mm 4 run

2.50 sq mm 2 run

4.00 sq mm 2 run

Supply and drawing bare earthing conductors of the following sizes along with wiring/cables and giving connection as required. 2.00 mm copper conductor (14 SWG)

2.65 mm copper conductor (12 SWG)

3.15 mm copper conductor (10 SWG)

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper/brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall, making good the damages, colour washing etc. as required. 4 way (8 + 12 ) three phase double cover (IP 42/43)

Supply and installation of the following acessories suitable for 50 Hz AC supply conforming to IS 8828-1995/IEC 60898 of the following current ratings in the existing enclosure and giving connections as required 63 A four pole mini break isolator

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.  - 63 AMPS

6 A to 32 A, 10 kA, SP MCB

Supply, conveyance installation testing and commissioning of ceiling mounding down light fitting Bajaj BJMMR / CRFFG 1 x 4 W L E D Warm Light square/ round type of complete with all accessories of all type directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply, conveyance installation testing and commissioning of ceiling mounding down light fitting Bajaj BJMMR / CRFFG 1 x 6 W L E D square/ round type of size 100mm ( or equivalent) complete with all accessories of all type directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply, conveyance installation testing and commissioning of ceiling mounding down light fitting Bajaj BJMMR / CRFFG 1 x 12 W L E D square/ round type of size 100mm ( or equivalent) complete with all accessories of all type directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply, conveyance installation testing and commissioning of ceiling mounding down light fitting Bajaj BJMMR / CRFFG 1 x 18 W L E D square/ round type of size 100mm ( or equivalent) complete with all accessories of all type directly on ceiling including giving connection with required length of 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring etc. as required.

Supply , conveyance, installation, testing and commissioning wall mounting fan of the following size using mounting brackets supplied along with the fan and giving connection with existing wire. 300 mm sweep

Providing and fixing Flexi LED Strip for Cove Lighting (5 Metre 12 W with Driver ), Wipro / Bajaj / Philips Or Eqivalent.

Supply , conveyance, installation, testing and commissioning wall mounting fan of the following size using mounting brackets supplied along with the fan and giving connection with existing wire. 300 mm sweep