Kerala Health Research And Welfare Society Tender

15.3 : Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

15.12.1 : Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

15.57 : Dismantling aluminium / Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 metres lead as directed by Engineer - in-Charge

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

12.45.2 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum fire resistant board conforming to IS; 2095-Part I

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.82.2 : Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats

13.111.1 : Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

13.99.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :One or more coats on old work

od165006/2024_2025 : Providing and laying vitrified floor tiles in different sizes with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments, Labour etc., complete. Size of Tile 600 x 600 mm. Make: Simpolo Ceramics, Colour: Grey/Cream, Finish: Matt, Thickness: 16mm.

od165007/2024_2025 : Providing and fixing vitrified wall tiles conforming to IS: 15622, of approved make, in all colours, any size as approved by Engineer in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. Size of Tile 600 x 600 mm. Make: Simpolo Ceramics, Colour: Grey/Cream, Finish: Matt, Thickness: 9mm.

8.2.2.2 : Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.Area of slab over 0.50 sqm

od162696/2024_2025 : Grouting the joints of Floor & Wall tiles having joints of 3 mm width, using Epoxy Grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge. Size of Tile 600mm x 600mm.

od165008/2024_2025 : Providing and laying Exterior Floor tile (Designer tile) laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments, Labour etc., complete. Size of Tile 400 x 400 mm. Make: Simpolo Ceramics, Color: Grey, Finish: Matt, Thickness: 16mm.<br>

21.1.1.2 : Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

od162103/2024_2025 : Providing and fixing 4mm thick aluminium composite panelling fixed in aluminium door window ventilator shutter portion EPDM rubber neoprin gasket etc. complete.

9.84 : Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width form 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

9.72.4 : Providing and fixing bright finished brass butt hinges with necessary screws etc. complete:100x70x4 mm (ordinary type)

od162535/2024_2025 : Supplying and fixing maruti lock

od162488/2024_2025 : Suupplying and fixing 150mm aluminium tower bolt

od162489/2024_2025 : Supplying and fixing 150mm aluminium door handle

21.3.1 : Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

9.121 : Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminated shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

9.122.1 : Providing and fixing to existing door frames.30 mm thick Glas Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS : 14856, including fixing to frames.

od162581/2024_2025 : Providing and fixing Horizontal Blinds (Zebra Blind) With Premium Quality fabric with one year service period and its accessories, including cost of Labor.

od164647/2024_2025 : Supplying and installation of 6mm thick Exterior grade F- Quality panels of standard size of one of the following: 1.3 x 2.8 m /1.854 x 2.8 m / 1.3 x 4.1 m / 1.854 x 4.1 m, with both side décor of FunderMax make or equivalent .The panels must be duromer high-pressure laminates (HPL) as per EN 438-6 type EDF with norm conformity as per EN 438-7 manufactured using NT Technology (Non-fading high performance acrylic polyurethane surface technology) conforming to norms with CE Mark. Panels are double hardened including acrylic polyurethane resin which is thermally cured under high pressure. Material should be class B / class 1 complying with NBC 2016, ASTM E 84, BS 476 - 7<br>Installation of these panels must be done by MBE Rivets(with Fixed and Sliding Points) with minimum recommended Aluminum T section of 75x37x2 mm thick and L section 40x37x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anchored by standard Hilti/Fischer or equivalent make anchor fasteners along with Thermal Separator. Including Installation Charges by the Trained teams with a 10 year Full system warranty. Make: FunderMax.<br>

od167158/2024_2025 : Providing and Installing Storage cabinet below Wash counter, Storage cabinets above sink slab (Side), Openable Single door Wardrobe at room, made with using a combination of 9mm and 16mm Boiled water proof (BWP) 710 Grade Plywood finished with 1mm Laminate on both sides & 2mm Edge bands Including all materials, Fittings (Handles, Auto close Hinges) and labour charges etc.. Approved Boards: Trojan/Green Ply, Laminates: Merino/GreenLam, Accessories & Hinges: Hettich.

od162583/2024_2025 : Labour engaged for petty repairs (carpenter)

od162584/2024_2025 : Labour engaged for petty repairs (Welder)

od162585/2024_2025 : Labour engaged for petty repairs.(Aluminum fabricator)

od162586/2024_2025 : LaboUR engaged for petty repairs (plumber)

od162587/2024_2025 : Labour engaged for petty repairs(Bhisti)

10.16.1 : Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished welded type tubes

50.12.2.4 : Providing & fixing Poly carbonate multi wall plain sheet 6 mm thick as approved by the Engineer in charge and should be supplied in a single length of 12m or as decide by the Engineer in charge. The sheets shall be fixed using self drilling/self tapping screw of size (5.5x55mm) with EPDM seal complete upto any pitch in horizontal/vertical curved surfaces, but excluding the cost of purlins, rafters, trusses, and including cutting to size and shapes where ever required.

15.60 : Disposal of building rubbish/ malba/ similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved

APPENDIX 2 SANITARY & WATER SUPPLY WORKS

od155587/2024_2025 : Supplying and Fixing Premium Quality Water Mixer with Long Bend Pipe Over Head Shower(Square Type) with Arm & flange. - Mixer Make: Essco by Jaquar, ModelNo- ESS-517B TQT. Make: Viking Rain shower square drizzle, Model no-8426. and Make: Viking rain shower arm round & flange polish, model no-8714.

od164833/2024_2025 : Providing and fixing white vitreous china Single piece floor mount pedestal type water closet (European type WC pan) with seat and lid, flushing cistern, including flush pipe, conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: WC pan with soft close solid plastic seat and lid of make: Essco by Jaquar, model- essco rimless S/PC WC with PP S/CL (101853p180sppsm), Colour: White

od164863/2024_2025 : Providing and fixing Quartz sink with C. I brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required: Quartz sink of size 500x400x250 mm of make: Reginox, Model-Amsterdam 50, Colour: Caffe Silvery.

od164832/2024_2025 : Providing and fixing Premium Quality Sink of size 600 mm Under mount SGL Basin type with racks, C.P. brass chain with rubber plug, 40 mm C.P Sink brass waste Coupler complete, including painting the fittings and brackets, cutting and making good the walls wherever required: Sink- Make: kholer, Model- Cairn, no- 28001-CM1.& Kholer Sink Waste coupler 7400

od163425/2024_2025 : Supplying and Fixing Premium Quality Hand Shower, Long Bend Pipe Over Head Shower(Square Type) with Arm & flange with all of its Internal and External Components such as: Jaquar Concealed body for S/L High Flow Diver, Jaquar Exp Part kit of Hi Flow, Jaquar opal prime B/Tub Spout with button and Essco Hand shower pack flow 70m CHR-SAE.<br>Make: Jaquar Concealed body for S/L High Flow Diver, Model No-079N, Make: Jaquar Exp Part kit of Hi Flow 1, Model No-5079NKPM, Make: Jaquar opal prime B/Tub Spout with button Model No- 15463PM, Make: Essco Hand shower pack flow 70m CHR-SAE Model No:551SH555, Make: Viking Rain shower square drizzle, Model no-8426, Make: Viking rain shower arm round & flange polish, model no-8714.

od155624/2024_2025 : Supplying and Fixing Stainless Steel Vertical Fold-able Type Toilet Grab Bar of Superior Quality including its screws etc.. make: Jaquar, model- SP-WAC BG0800CSN, Finish- Satin.

od155625/2024_2025 : Providing and Fixing Toilet Stainless steel Grab Handle of Superior Quality. Make: Viking, Model No- H2O-1168

od155829/2024_2025 : Supplying and Fixing Wall Hung Shower Seat of Superior Quality, with necessary screws and fittings. Make: Kholer, Model No-20526IN-0

od155837/2024_2025 : Providing and fixing towel rack of length 600mm complete with CP brass screws with concealed fitting arrangement of approved quality and colour. Make: Calista, Model no- CS507

od155838/2024_2025 : Providing and fixing Towel Ring ovel shape with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms. make: Auga, Model no- Ag103- Brass- Chrome.

od155841/2024_2025 : Supplying and Fixing Oval Shape mirror of Size 450 mm x 600 mm of good Quality. make: Kriztle, model no-LM1002.

od155842/2024_2025 : Providing and Fixing Stainless Steel Gratings Square (Flat) Make: Viking Drain Flat Square, Model 39405

od164695/2024_2025 : Supplying and fixing 110 mm dia. or nearest size floor trap

od155843/2024_2025 : Supplying and fixing Soap dish S.S including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. Make: Calista, Model No- CS 402

od155844/2024_2025 : Supplying and fixing Health Faucet superior quality ( Jaquar) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge. Make: Jaquar, Model No- 573

od155845/2024_2025 : Providing and fixing Sink cock extd swinging spout of approved quality : make: Jaquar, model no- 5347-SD.

od155846/2024_2025 : Providing and fixing angle cock + flange for basin mixer and geyser points of approved quality conforming to IS: 8931. make: Jaquar, model no- 3057-MN (round body)

od155847/2024_2025 : Providing and fixing toilet roll holder with flap: make; Jaquar, model no- 1153S.

od155848/2024_2025 : Providing and fixing Plastic Liquid Dispenser of standard shape with bracket of the same materials with snap fittings of approved quality and colour. make: Viking, Model no- 1125

od155866/2024_2025 : Supplying and fixing Corner Glass Shelf for toilet of 8 mm thick, Make: Calista, Model No- RG SP-09-09-8 MM CP

18.8.2 : Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes& fittings, with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc.20 mm nominal outer dia pipes

50.18.8.3.2 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 25 mm pipe 10kgf /cm2

50.18.8.4.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 32 mm pipe 10Kgf/cm2

50.18.8.7.1 : Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work including cutting chases and making good the wall etc. 63 mm pipe 6 Kgf/cm2

50.18.9.20.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Elbow

50.18.9.20.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 63 mm dia Bend

50.18.9.20.5 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes including jointing with PVC solvent cement - 63x63x63 mm dia Tee

50.18.9.20.9 : Providing and fixing PVC moulded fitting / accessories for Rigid PVC pipes, including jointing with PVC solvent cement-63 mm dia Socket /coupling

50.18.9.19.1 : Providing and fixing PVC pipes including fixing the pipe with clamps/ clips/ at 1.00 m spacing . This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 110 mm dia 6 Kgf/cm2 - External work- Exposed on wall

50.18.9.22.1 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia Elbow

50.18.9.22.2 : Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow

50.18.9.22.3 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement-110 mm dia Door Elbow

50.18.9.22.4 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend

50.18.9.22.5 : Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee

50.18.9.22.11 : Providing and fixing PVC moulded fittings/accessories for Rigid PVC pipes,including jointing with PVC solvent cement - 110 mm dia Socket/ coupling