Kerala Agricultural University Tender

15.7.4:Demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.In cement mortar

OD421/2024-2025:Providing and constructing Autoclaved Aerated Block (A.A.C) Masonry works consisting of min 60% of fly ash content using 'Renabond' or equivalent block adhesive with a thickness of 3 to 5mm to be used as per manufacturer's instructions. (within 200 kms from project site) A.A.C BLOCKS of size 600x200x200mm. Minimum Compressive strength of 4 N/mm2 and conforming to IS:2185 ( Part - 3 ) for all types of masonry works, at all depths and heights including providing openings and projections, raking of joints, scaffolding and curing etc., complete as per specifications, drawings and direction of the Authority. The necessary RCC vertical Mullions/ columns and horizontal RCC tie & RCC lintels over opening are to be provided in specified location as per Engineering in-charge . (Only reinforcement steel to be paid separately as per Boq item:5) Pl Note : Gap between the topmost course and ceiling/ beam less than 100mm shall be filled with lean concrete made of 12.50mm downsize aggregate of strength comparable with the blocks. No separate measurement is to be given and this item is measurable in the blockwork item itself. Grade of Lean Concrete M10.

5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22A.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

13.80:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

21.3.2:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 5.50 mm thickness

OD422/2024-2025:Providing PVC ceiling with TKT board of 9mm or nearest thick,supreme quality sheets by dovetail locking system using 25mm x 25mm anodized aluminum square tubes (section no 14477, 800 gm/ 3.60m length) for frames ( Spacing not exceeding 45 cm c/c), 25 x 1.50 mm flat(section no 10116, 380 gm/ 3.60m length) for suspenders, 20x20 mm PVC ornamental Cornish for sides and suspending the ceiling to the required line and level including all cost of materials and labour charges etc. complete.

11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

OD423/2024-2025:Providing and fixing 8mm PVC foam board (coloured multiwood), in aluminum fabricated partition frames excluding the cost of aluminium extrusions as per architectural drawings and directions of Engineer - in- Charge.

OD424/2024-2025:Providing andfixing SS hinges

OD425/2024-2025:Providing and fixing 250mm SS aldrop

OD426/2024-2025:Supplying and fixing best quality door closer

OD427/2024-2025:Providing anodized powder coated aluminium handle - 20 cm length

13.83.2:Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour.Two coats

OD428/2024-2025:Providing and fixing 12mm thick cement board (Density 1350kg/m3, water absorption <= 35%) including providing and fixing of frame work made of 38mm x 38mm size GI square tube with neccessary screws and bolts all as per manufacturer's specification , all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting