HLL Lifecare Limited Tender

Civil Works

2.8.1 Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

4.1.8 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

7.1.1 Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with: Cement mortar 1:6 (1 cement : 6 coarse sand)

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

6.3.2 Brick work with common burnt clay machine moulded perforated bricks of classdesignation 12.5 conforming to IS: 2222 in superstructure above plinth level up tofloor five level in cement mortar 1:6 (1 cement : 6 coarse sand): With Modular bricks(from floor 2 level up to floor 5 level)

13.1.1 12 mm cement plaster of mix: 1:4 ( 1 cement : 4 fine sand)

5.3 Reinforced cement concrete work in beams, suspended floors, roofs, having slope up to 150 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone III) : 3 graded stone aggregate 20 mm nominal size).

5.9.5 Centering and shuttering including strutting, etc. and removal of form for: Lintels, beams, plinth beams, girders bressumers and cantilevers

5.22A.6 Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo - Mechanically Treated bars of grade Fe-500D or more

10.16.2 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

11.41.2 Providing and laying vitrified floor and wall tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600 x 600 mm

13.80 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.43.1 Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

13.46.1 Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

13.60.1 Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

13.99.1 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge ( Door handle, lock and stopper etc to be paid separately)

MR Providing and fixing Stainless Steel H type door handles for Toughened Glass of 25mmx450mm Size

MR Providing and fixing Stainless Steel Lock Patch Fittings for Floor including cutting of Floor and Making It good

MR Providing and fixing 3M Fasara frosted etching film of thickness 25 microns self-adhesive of approved colour, shade, and quality with cutting as per approved design and pattern, including cleaning of glass and making surface smooth for fixing of film to the surface, all completed as per the direction of the engineer in charge.

21.1.1.2 Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portion and Shutter Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.3.1 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness

25.7 Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Alumini um sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

False Ceiling Work

12.52.4 Providing and fixing tiled false ceiling of approved materials of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams per sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x 1.6 mm fixed to ceiling with 12.5mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x 30x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer -in-charge. 12.5 mm thick fully Perforated Gypsum Board tile made from plaster board having glass fibre conforming to IS: 2095 Part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with centre borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side , having as NRC ( Noise Reduction Co efficient) of 0.79, with 50 mm resin bonded glass wool backing.

50.12.4.1 Providing and fixing false ceiling with 7.5 mm thick PVC plain panel board ceiling of approved quality in aluminium frame work with necessary screws etc complete. Including Supports and frameworks

Furniture Work

MR Double Level Counter: Providing and fixing of Double Level Counter,Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on one side and other side balancing lamination, first step at 750 mm from ground, 900mm wide and Counter top at 1050 mm level and 300 mm wide. 12mm thick acrylic sheet (pure white in colour) to be used for counter top on 25 mm thick prelaminated commercial ply at counter top. Display unit with 8mm thick toughened glass fascia and 18mm thick prelaminated shelves to be in built in counter with movable shutter. Counter should contain retractable keyboard trays and partitioned drawers with drawer channel, cupboard units with 3nos sliding drawers. Drawers and cupboard are to be fixed with individual locks and handles. Cable manager and leg space all Complete as per the design and instructions of engineer in charge. 12mm thick toughened glass partition to be provided above counter up-to roof height with necessary counter opening. Note: Only front elevation of wooden counter will be measured under this item. (12mm thick toughened glass will be paid separately). Make laminate: GREENLAM, MARINO or equivalent.

MR Table of size 1200x600x750mm Made of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on one side and other side balancing lamination of approved colour and pattern as per the design. The table is provided with 3 drawer pullout with necessary hardware like sliding channel cable manager, multipurpose locks, handles, mini fix, dowels and screws. Exposed edges to be finished with 0.8 mm edge band as per specified colour.

MR Counter Height Stools : Supply and errection of counter height stools ( bar stools ) of following specifications :Revolving adjustable Chrome plated steel body chairs with resistance to the corrosion. Cushion Seat with Lift mechanism for Adjustment of height. Minimum height 750mm before expansion. Medium Back rest and arm rest. Item shall be of reputed make.

MR Medicine display shelf: Providing and fixing of Open Wooden display laminated cabinets of length 900mmXheight 2500mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on both side with proper provision of racks and shelves. Bottom storage unit of 600mm deep storage shall be 750mm from the ground with display wooden shelves @150mm C/c. Upper storage unit provided with display wooden shelves @150mm C/c and 450 mm deep and height of 1750mm from the bottom storage unit . All the edges to be finished with edge band and shelves to be fix with proper bracket holders complete as per approved layout, drawings and instruction of Engineer In Charge. Note: Only front elevation will be measured.

MR Storage Cabinet: Providing and fixing of storage cabinet of dimension 900mmX450mmX600mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on both side including inside middle partitions and with 4mm thick Sliding glass door on front, handles, locks etc. All the edges to be finished with edge band and shelves to be fix with proper bracket holders complete as per approved layout, drawings and instruction of Engineer In Charge. Note: Only front elevation will be measured.

MR Revolving Chair: Medium back ergonomic chair with five nos. star shaped Nylon base. Castor: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment , Fixed armrest providing natural resting for arms. Seat with PU coated foam backed fabric, back rest with mesh type fabric, upholstery: Heavy duty rubber backed fabric in BLACK

MR Slotted Angle Racks : Supply and errection of Powder coated slotted angle metalic rack having min 8 shelfs made up of min 40 X 40 X 2 mm size rolled steel angle posts shall have 8-mm diameter holes provided at 50-mm centre to centre. Metal shelves shall be made from mild steel sheets not less than 1.0 mm in thickness and with sufficient stiffners. Shelves shall have lipped flanges width of flange being 30 mm and depth of lip 15 mm .Min size of rack 900mm Length X 300mm Depth X 2000mm Height.

MR Providing a fixxing steel drawer cabinet with 60 Nos plastic pullout rack for Medicine storage features a full steel body enamel finished. Each drawer should be made from high-quality polypropylene, designed with a stop rim to prevent accidental removal. Rubber feet should be provided to protect surfaces from scratches and ensure stability. The cabinet must be suitable for both free-standing and wall-mounted installation, allowing flexibility as per project requirements. The external dimensions shall be 150 mmx 300 mmx and 500 mm.

Plumbing Work

17.2.1 Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid, Including Angle valve and connection hose

17.7.2 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630 x 450 mm with a single 15 mm C.P. brass pillar tap, Angle valve, 45cm connection hose, 32mm flexible hose etc.

18.51.1 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

50.17.1.4 Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in-charge. With angle valve

50.18.8.2.2 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2

50.18.7.3.1 Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer- in- Charge 25 mm dia 12 Kgf/cm2 - Internal work - Exposed on wall

50.18.7.4.2 Providing and fixing PVC, pipes fittings including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 32 mm dia 6 Kgf/cm2 - internal work- Exposed on wall

50.18.9.9.1 Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling & testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2

MR Supplying and fixing PVC Floor Trap 100mmx75mm size without Jali including cutting open, boring through RCC slabs and making good the damages. Including SS Gratings of Rectangular type with openable circular lid 150 mm nominal size

18.48 Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Electrical Work

1.10.3 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

1.12 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. (Recommended Material : Polycab, RR Kabel, V Guard, Havells)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (Recommended Material : RR Kabel/National/ Ralison/RKG/ Finolex / Polycab / Havells)

1.14.1 2 x1.5 sq.mm + 1x 1.5 sq. mm earth wire

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire meter

1.33 Supplying and fixing 3 pin 5 A ceiling rose on the exising junction box / wooden block including connections as required.

S/F light plug point modular type accessories : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required,

S/F Power plug point with modular type switch : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 and 15/16 amps modular switch, connection,painting etc as required.

S/F 20A SPN MCB industrial socket outlet : Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F Modular boxes, base & cover plate : Supplying and fixing 1 or 2 module ( 75 mm x 75 mm), GI box along with modular base, cover plate for modular switches in recess etc as required.

S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole and neutral

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.

UPS DB - Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCBIRCCB/Isolator 16 way, Double door

Raw DB - Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door

 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making goMR the damages , colour washing etc. as required. 4 core 16 sq mm with factory made clamp

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 4 X 16 sq. mm (19mm)

Supply, Installation, testing and Commissioning of Outdoor rated three phase electronic type energy meter with LCD display with battery backup, class 1.00 CT. The whole unit to be mounted on suitable metal enclosure (powder coated with locking arrangement, separate enclosure for incoming and outgoing) with required HRC fuses/MCB/RCCB as required, Neutral link and all connections complete

Supply, installation, testing and commissioning of the following types of light fittings with all accessories on false ceiling, true ceiling or wall as directed and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. All recessed type fixtures are to be supported independently with chains or GI wire anchored to the ceiling with anchoring bolt of necessary size. All loose wires above the false ceiling are to be neatly concealed by flexible metal/pvc conduits.( cost to include lamps & all consumables also)

Supply and installtion of 30-36W, 230V, 4300 lumen, Surface/Recessed Square LED Cool White light fixture of dimession 300mm X 300mm on false ceiling along with all accessories with intergrated driver THD10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Crompton/Wipro or equivalent.

Supply and installtion of LED tubelight of 6000K and 20-24W on wall or ceiling as directed and giving connections as required. All loose wires are to be neatly concealed. (Make: Philips, Wipro, Crompton or equivalent)

Supply and installtion of 10-15W, 230V, Surface/Recessed Square or Round LED Cool White light fixture on false ceilling along with all accessories with intergrated driver THD10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Havells/Wipro or equivalent.

 Supply, Intallation, testing and Commissioning of 250mm sweep, Single phase Light duty exhaust fan having High Suction at low noise with aerodynamically designed blades, silent, 100% copper motor along with all mounting accessories complete

Supply, Installation, testing and commissioning of wall mount fan (400mm sweep), adjustable speed. min 60 degree oscillation, swing, Adjustable upward and downward tilt mechanism, Protective Guard, Including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, mounting accessories, etc. as required. It shall be double ball bearning type. (Make: USHA, Cromption , Havells)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

SITC of Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled Split Type Air Conditioner of following capacity consisting of cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary/twin rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room unit on Ceiling, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 3m, canvas connections, full electrical/communication cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer etc complete as required. ( Make : Voltas, Carrier, Blue Star, Hitachi, LG ) : 1.5 TR 3 star rated as per BEE

Network

8 Port Network Switch : Supply, Installation, testing and commissioning of : 10/100 Mbps 8-Ports Gigabit Switch . ( Make : D-Link/commscope/Netgear)

Providing and Fixing of RJ-45 socket outlet in the existing modular box with connections and all required.

Supplying,drawing and crimping with all accessories of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable from Port Switch to Data socket

Supply, installation, testing and commissioning of best quality cat-6 patch cord having 1 metre length complete as per specifications as required.

Supply of ABC Type fire extinguisher of 2 Kgs. Make SAFEX / MINIMAX / CEASEFIRE or equivalent

CCTV

Supply, Installation, Testing & Commissioning of Indoor IR Dome night vision cameras : 2.0 MP, 0.1 lux, Resolution 720 P ,AWB/ BLC/ AGC, min 20m range, Built-in IR illumination, white color case, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply, Installation, Testing & Commissioning of Outdoor IR Bullet night vision camera :2.0 MP,0.1 lux, Resolution 720 P,AWB/ BLC/ AGC ,min 20m range, Built-in IR illumination, white color case, DC12V, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply, Installation ,Testing & commissioning of Network Video Recorder : 8-Channel Embedded 4k, Real-time, with 4 TB Hard Disk (Make: Seagate/WD?Samsung) shall be inclusive of all accessories, termination of cables, etc complete. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply and Installation of LED Color Monitor of minimum 21 inch screen, complete, FHD display with wireless mouse Make: LG/Samsung or equivalent.

Providing 4U Rack including accessories. Make:CP Plus, Netrack

Supply and Installation of SMPS Power Supply Unit of 230V, capacity miniumum 450W including accessories

Earthing

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along with existing surface/ recessed conduit/ submain wiring/ cable as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required

Capital items

Supply, Installation, Testing and Commissioning of 3 kVA True Online UPS system as per IEC 62040-3 with 415 +/- 15% V, 50 Hz, Single Phase input & Single Phase Output woring on 16 bit Microprocessor architecture, with inbuilt isolation transformer, 1 hour battery back up, battery rack accessories, suitable copper cabling work from incoming switch and to outgoing switch is also under contractor scope. Make: Liebert/Numeric/APC

Laserjet Multi functional Monochrome Network Printer Supply and Installation at site, All in One Laserjet Multifunction Monochrome Printer having LCD Display, with functions to copy, print and scan, print resolution 600 dpi x 600 dpi, 20 ppm print speed, Duty cycle minimum 8000 pages per month, 24 bit depth, USB, Wi-Fi connectivity. Make : hp/brother/canon/epson or equivalent, for Bill Printing cum Office use with Warranty period of one year. Connectivity: Hi-speed USB 3.0 Supported, Wi-Fi, Media Types: Paper, envelopes, labels, cardstock, transparencies, postcards, Functionality: Print, Scan/Copy. Power Consumption: Maximum 250 Watts Recommended Make : hp/brother/canon/epson or equivalent

Laserjet Monochrome Network Printer Supply and Installation at site, Laserjet Monochrome Printer having LCD Display, with functions to copy and print, print resolution 600 dpi x 600 dpi, 20 ppm print speed, Duty cycle minimum 8000 pages per month, 24 bit depth, USB, Wi-Fi connectivity. Make : hp/brother/canon/epson or equivalent

Visi Cooler / Pharmacy refrigerator : Supply, errection and commisioning of lab / pharmacy refrigirator as per following specifications : Upright Showcase Coolers/refrigerators with Single Glass Door and Lock having 350-450 Litre capacity, Temperature range capability 1-10 degree celsius with Digital Temperature Controller and Display, Minimum of 4 adjustable Shelves/Racks Recommended Make: CELFROST, BLUESTAR, VOLTAS, THERMO FISCHER

Supply and Installation of Server PC - Desktop PC having following spec: Processor: 12th or Higher Gen Intel® Core™ i5 - (30 MB cache, 16 cores) Memory: 16 GB: 2 x 8 GB, DDR5 Video Card: Intel® Graphics Storage: 1 TB, M.2 2230, PCIe NVMe, SSD, Class 35 OS: Windows 10/11 Pro English Chassis: Mini Tower, Tower Wired Multimedia Keyboard and Mouse Integrated Wireless LAN Integrated Gigabit LAN Monitor 21.5 LED or higher. Make:HP/Dell

Supply and Installation of Client PC - All in One Desktop 12th Gen Intel® Core™ i3 -12th gen or better 2.5 GHz to 4.5 GHz Turbo) Memory *8 GB: 1 x 8 GB, DDR5 Storage: 512 GB, M.2 2230, PCIe NVMe, SSD, Class 35 OS: Windows 11 Pro English Multimedia Wired Keyboard Optical Mouse 2 USB 3.2 Gen 1 ports Integrated Wireless LAN Monitor 21.5 LED or higher. Make : Dell / HP or equivalent

Cash Safe (Coffer) Volume. 14 L Min WallThickness: 2.5 mm min for body and 5 mm min for door Recommended Make: Godrej make, Model No. Premium Coffer BRN (ltem Code: SEBP 1112) or equivalent (only manual lockinq system)

Water Dispenser: Supply and errection of water dispenser can hold 20 litre water bottle having normal standing design with 14 liter refrigerator at bottom and having 3 temperature taps hot, plain and cold. 3 liter cooling and 5 liter heating capacity per hour. Body made of ABS plastic and tank made of Food grade stainless steel. Heavy duty bottle piercer with bottle holder. with min 1 year warranty. (Make : voltas / Blue star/ equivalent)

Branding

Backlit Flex Board: Supply, installation, testing and commitioning of backlit flex board box having min 100mm depth and in approved size and design with minimum 2 nos of LED tubelight of 6000K and 18W per 1 Sqm of board`s front elevation . The board shall be fabricated out of painted GI metal sheet on all sides excluding front and to be fixed over welded and painted 25X25X3mm MS angle frame in flex board size . The front side of the board should be fabricated with good quality PVC flex sheet printed in approved design and to be neatly fixed with GI sheet . The board shall be properly fixed in suitable location in proper line and level with all necessary fastners, supports etc. Electrical works likes electrical internal board wiring, connections, fittings, externaly fixed weather proof 2/3 pin plug points and sockets including its board etc. to be complete properly. All fabrication should be done as per aproved design and instructions of Engineer in Charge. Note: Only front elevation will be measured.

Supply and fixing of Flex media board as given design. The frame work must be in the suitable size of GI section tubes (Minimum size of GI section: 1squire inch). The flex media Quality: High Quality Glossy Opaque BACK media . Printing quality must be: 8pass.

MR Providing and fixing one way visible printed film for glass self-adhesive of approved design and pattern, including cleaning of glass and making surface smooth for fixing of film to the surface, all completed as per the direction of the engineer in charge.