HLL Lifecare Limited Tender

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

12 mm cement plaster of mix: 1:4 ( 1 cement : 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: Water thinnable cement primer

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile including applying additional coats wherever required to achieve even shade and colour. Two coats or more cots

Cleaning of existing floor tile with tile cleaner including all required as per instruction of Engineer In Charge.

Providing and laying Glazed/Matt finished Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints. Size of Tile 600x600 mm

Providing and laying Glazed/Matt finished Vitrified tiles in different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in wall, skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints . Size of Tile 600x600 mm

Steel work in built up tubular ( round, square or rectangular hollow tubesetc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, and two or more coats of Enamel Paint including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ .05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel rade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main “T” runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick(minimum) sheet, spaced at 1200 mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottomexposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and asdirected by Engineer-in-charge. 8 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard, manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit.

Providing and fixing 12 mm thick frameless toughened glass partition of approved brand and manufacture, including top & bottom fixing arrangement counter opening and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Providing and fixing of single glass door SS Patch Lock with out handle in toughened glass door including all necessary screws etc. complete.

Providing and fixing SS H handle having min 450 mm length in toughed glass door including all necessary screws etc. complete.

ACP : Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding over Aluminium rectangular tube of minimum size 50x25x2mm, with open grooves for linear as well as curvilinear portions of the building, for all heights and all levels etc. including: a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metallic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing. The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics including all required & complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in Sqm. up to two decimal places.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden lock in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat ressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin- charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

PLUMBING WORKS

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps

Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 30cm length

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chased and making good the wall etc. : 20 mm pipe 12 Kgf/cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge.Exposed Work

32 mm dia 10 Kgf/cm2

50 mm dia 10Kgf/cm2

110 mm dia 6 Kgf/cm2

FURNITURE WORKS

Double Level Counter: Providing and fixing Double Level Counter made up of prelaminated 18mm thick MDF board with dimension 1200mm lengthX 600mm widthX 1100mm height, first level top at 750 mm from ground having 600mm wide and second level top at 1100 mm level having 300 mm wide. 12mm thick acrylic sheet (pure white in colour) to be used for counter tops over MDF board . Front side display unit with 8mm thick toughened glass fascia and shelves to be built in table. Counter should contain retractable keyboard trays and partitioned drawers with drawer channel, cupboard units with swing door and auto close hinges. Drawers and cupboard are to be fixed with individual locks and handles. Cable manager and leg space are also to be provided. All edges to be fitted with 2mm thic PVC edge beeding. All complete as per the design and instructions of engineer in charge. 12mm thick toughened glass partition to be provided above counter with necessary counter opening. Note: Only front elevation of wooden counter will be measured. (12mm thick toughened glass will be paid separately). Make laminate: GREENLAM, MARINO or equivalent.

Counter Height Stools : Supply and installation at site counter height stools of following specifications :Revolving adjustable Chrome plated steel body chairs with resistance to the corrosion. Cushion Seat with Lift mechanism for Adjustment of height. Minimum height 750mm before expansion. Medium Back rest and arm rest. Item shall be of reputed make.

Table: Supply and errection of Working Table 900mm length X600mm depth X750mm height made with 18mm thick prelaminated particle board with one side decorative and other side balancing lamination and all edges to be fixed with matching PVC edge beeding. Partitioned storage unit having swing door ,Partitioned cash drawer, Key board drawer and leg space are also to be provided with individual locks and handles, autoclose hinges, drawer channels etc. complete as per the aproved design and instructions of engineer in charge.

Chair: Supply and errection of Medium back ergonomic chair with five nos. Star shaped Nylon base. Castors: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric. Upholstery: Heavy duty rubber backed fabric in BLACK.

Medicine display shelf: Providing and fixing of Open Wooden display laminated cabinets of length 900mmX height 2500mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS: 14587 with decorative lamination on both side with proper provision of racks and shelves. Bottom storage unit of 600mm deep storage shall be 750mm from the ground with display wooden shelves @150mm C/c. Upper storage unit provided with display wooden shelves @150mm C/c and 450 mm deep and height of 1750mm from the bottom storage unit. All the edges to be finished with edge band and shelves to be fixed with proper bracket holders. All complete as per approved layout, drawings and instruction of Engineer in Charge. Note: Only front elevation will be measured.

Over Head Storage Cabinet: Providing and fixing of Over head storage cabinet of dimension 900mmX600mmX450mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on both side including inside middle partitions and with sliding door on front side with rollers, sliding channels, handles, locks etc. All the edges to be finished with edge band and shelves to be fix with proper bracket holders complete as per approved layout, drawings and instruction of Engineer In Charge. Note: Only front elevation will be measured.

Airport Chair, 3 Seater: Supply and erection of Airport Chair (Set Of 3 In 1) having overall dimension of Length 1720mm x width 675mm x height 850mm. Chair dimension floor to seat height 400mm and floor to arms height 600mm seat and back frame size Length 495mm x width 490mm x height 550 mm. Chair arms is made up of Stainless Steel Tube 50mm X 25mm Oval Shapes Tube 1.6mm thickness. Legs are made to 48mm Stainless Steel round Tube 2mm thickness and seat and back frame made to 19mm Stainless steel round tube 1.2mm thickness. Seat and back use to 1.2mm thickness perforated Stainless steel sheet. All the end cups are made to stainless steel glossy finish cups and using for the floor levellers 10mm nylon adjustable bush.

DISPLAY WORKS

Backlit Acrilic Board with projected letters: Supply, installation, testing and commissioning of weatherproof backlit acrilic board with projected letters made upof 20mm thick acrilic board and having box depth of min 100mm in approved size and design with reqired LED strips for high glow light. The board shall be fabricated and fixed over suitable welded and painted 25X25X3mm MS angle frame in suitable location and in proper line and level with all necessary fastners, supports etc. Electrical works likes electrical wirings, connections, fittings, externaly fixed weather proof 2/3 pin plug points and sockets including boxes etc. to be complete properly. All fabrication and fixing should be done as per approved design and instructions of Engineer in Charge. (Note: Only front elevation will be measured.)

Vinyl Transparent One Way Vision Glass Stickers: Supply and pasting of Vinyl Transparent One Way Vision Glass Stickers in approved size and design in glass partition and door as per the instruction of Engineer in Charge.

Providing & sticking/pasting of printed vinyl wall stickers as per approved size and design at all heights includes all the required as per the instruction of Engineer in Charge.

Providing & fixing of printed flex board as per approved size and design at all heights with proper framing, required fixtures etc all complete as per the instruction of Engineer in Charge.

Electrical Work

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. (Recommended Material : Polycab, RR Kabel, V Guard, Havells)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.( Recommended Material : RR Kabel/National/ Ralison/RKG/ Finolex / Polycab / Havells)

2 x1.5 sq.mm + 1x 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire meter

Supplying and fixing 3 pin 5 A ceiling rose on the exising junction box / wooden block including connections as required.

S/F light plug point modular type accessories : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required,

S/F Power plug point with modular type switch : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 and 15/16 amps modular switch, connection,painting etc as required.

Supply, Installation, testing & commissioning of branded best quality Single phase electronic type energy meter with LCD display with battery back up. with all connections complete, Make: L&T or Equivalent .

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator): 12 way, Double door.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator):8 way , Double door

S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Single pole and neutral

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 A

 Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3 core 16 sq mm with factory made clamp

Supply, installation, testing and commissioning of the following types of light fittings with all accessories on false ceiling, true ceiling or wall as directed and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. All recessed type fixtures are to be supported independently with chains or GI wire anchored to the ceiling with anchoring bolt of necessary size. All loose wires above the false ceiling are to be neatly concealed by flexible metal/pvc conduits.( cost to include lamps & all consumables also)

Supply and installtion of 30-36W, 230V, 4300 lumen, Recessed Square LED Cool White light fixture of dimession 600mm X 600mm on false ceiling along with all accessories with intergrated driver THD10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Crompton/Wipro or equivalent.

Supply and installtion of 10-15W, 230V, Recessed Square or Round LED Cool White light fixture on false ceilling along with all accessories with intergrated driver THD10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Havells/Wipro or equivalent.

LED tubelight of 6000K and 18W on wall or ceiling as directed and giving connections as required. All loose wires are to be neatly concealed .(Make :philips, Bajaj,Crompton or equalent)

Supply, Installation, testing and commissioning of wall mount fan (400mm sweep), adjustable speed. min 60 degree oscillation, swing, Adjustable upward and downward tilt mechanism, Protective Guard, Including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, mounting accessories, etc. as required. It shall be double ball bearning type. (Make: USHA, Cromption , Havells)

SITC of Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled High Wall mounted Split Air Conditioner of following capacity consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, making power interconnection between room & condenser , comprising of 25mm dia drain PVC piping with proper routing, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer, covering of cable and pipe with suitable casing cap etc allcomplete as required. ( Make : Voltas, Carrier, Blue Star, Siemens, Hitachi ) :2 TR 3 star rated as per BEE

Supply and Installation of additional copper piping, cabling and drain piping for air conditioning unit with proper insulation including all required on wall/above false ceiling with suitable casing cap etc complete.

Network

S/F Modular boxes, base & cover plate : Supplying and fixing 1 or 2 module ( 75 mm x 75 mm), GI box along with modular base, cover plate for modular switches in recess etc as required.

Providing and Fixing of RJ-45 socket outlet in the existing modular box with connections and all required.

8Port Network Switch : Supply, Installation, testing and commissioning of : 10/100 Mbps 8-Ports Gigabit Switch . ( Make : D-Link DGS-1008A)

Supplying,drawing and crimping with all accessories of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable from Port Switch to Data socket

Supply, installation, testing and commissioning of best quality cat-6 patch cord having 1 metre length complete as per specifications as required.

Supply, installation and commissioning of powder coated DVR 4U Wall Mounted Server Rack of ISO Standard of size 550 x 350 x 140 mm having depth adjustable mounting slots, top and bottom Panel with ventilation and cable entry facility, provision to mount the cooling fans on the top panel, lock and key etc. and having capacity to carry a max Load of 60 kg all complete as per the manufacturer specifications and instructions of Engineer In Charge.

CCTV

Supply, Installation, Testing & Commissioning of Indoor IR Dome night vision cameras : 2.0 MP, 0.1 lux, Resolution 720 P ,AWB/ BLC/ AGC, min 20m range, Built-in IR illumination, white color case, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply, Installation, Testing & Commissioning of Outdoor IR Bullet night vision camera :2.0 MP,0.1 lux, Resolution 720 P,AWB/ BLC/ AGC ,min 20m range, Built-in IR illumination, white color case, DC12V, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply ,Installation ,Testing & commissioning of Power supply unit for above camera as speficied by camera manufacturer -12VDC 10A

Supply ,Installation ,Testing & commissioning of Digital Video Recorder : 8-Channel Embedded HD DVR, 400fps, Real-time, with 2 TB HDD and English OSD, 230VAC. Rate shall be inclusive of all accessories, termination of cables, etc complete.

Supply ,Installation ,Testing & commissioning of 15" to 16" LED Color Monitor. make :LG / Samsung/ Equivalent.

Supply and Laying of Coaxial cable 2+1 RG59/RG6 premium quality CCTV power and video cable with ISI marked PVC conduit including terminations with suitable BNC Connector, power Jack etc complete.

CAPITAL/SUPPLY ITEMS

3 KVA Online UPS :SIT of 3 KVA Online UPS Systems of the following specifications :- True on - line 3 KVA UPS system. Inversion shall be Microprocessor controlled with instantaneous sine wave Control using IGBT. UPS shall have standard display features, alarms, safeties, etc Input Voltage range : A.C 235 V (+15% to -20%), 1 phase Input Frequency : 50 HZ (+/– 3HZ) Power Factor : 0.9 or above. THD : less than 5% ; Ripple Voltage in battery terminal : less than 2% DC Voltage Minimum Back up time : Continuous 60 Mins at full load Rectifier shall be Full wave Type (Shall fully meet the specified input power requirements) Battery Type : SMF, including battery rack.

Laserjet Multi functional Monochrome Network Printer: Supply and Installation at site, All in One Laserjet Multifunction Monochrome Printer having LCD Display, with functions to copy, print and scan, print resolution 600 dpi x 600 dpi, 20 ppm print speed, Duty cycle minimum 8000 pages per month, 24 bit depth, USB, Wi-Fi connectivity. Make : hp/brother/canon/epson or equivalent, for Bill Printing cum Office use with Warranty period of one year. Connectivity: Hi- speed USB 3.0 Supported, Wi-Fi, Media Types: Paper, envelopes, labels, cardstock, transparencies, postcards, Functionality: Print, Scan/Copy. Power Consumption: Maximum 250 Watts Recommended Make : hp/brother/canon/epson or equivalent

Laserjet Monochrome Network Printer : Supply and Installation at site, Laserjet Monochrome Printer having LCD Display, with functions to copy and print, print resolution 600 dpi x 600 dpi, 20 ppm print speed, Duty cycle minimum 8000 pages per month, 24 bit depth, USB, Wi-Fi connectivity.Make: hp/brother/canon/epson or equivalent

Visi Cooler / Pharmacy refrigerator : Supply, errection and commisioning of lab/ pharmacy refrigirator as per following specifications: Upright Showcase Coolers/refrigerators with Single Glass Door and Lock having 350-450 Litre capacity, Temperature range capability 1-10 degree celsius with Digital Temperature Controller and Display, Minimum of 4 adjustable Shelves/Racks Recommended Make: CELFROST, BLUESTAR, VOLTAS, THERMO FISCHER

Supply and installation of Server of Desktop PC with configuration, BRAND (DELL/HP or equivalent) - Desktop PC Processor: 12th or Higher Gen Intel® Core™ i5 - (30 MB cache, 6 cores) Memory: 16 GB: 2 x 8 GB, DDR5 Video Card: Intel® Graphics Storage: 1 TB, M.2 2230, PCIe NVMe, SSD, Class 35 OS: Windows 10/11 Pro English Chassis: Mini Tower, Wired Multimedia Keyboard and Mouse Integrated Wireless LAN Integrated Gigabit LAN Monitor 21.5 LED or higher.

Supply and installation of Server of All in One PC with Configuration, BRAND (DELL/HP or equivalent) - All in One PC 12th Gen Intel® Core™ i3 -12400 (18 MB cache, 4 cores, 8 threads, 2.5 GHz to 4.5 GHz Turbo) Memory *8 GB: 1 x 8 GB, DDR5 Storage: 512 GB, M.2 2230, PCIe NVMe, SSD, Class 35 OS: Windows 11 Pro English Multimedia Wired Keyboard Optical Mouse 2 USB 3.2 Gen 1 ports Integrated Wireless LAN Monitor 21.5 LED or higher.

Cash Counting Machine cum Fake Note Detector Make : Optimus-Model No.OLC 04 or equivalent

Cash Safe (Coffer) Volume. 14 L Min WallThickness: 2.5 mm min for body and 5 mm min for door Recommended Make: Godrej make, Model No. Premium Coffer BRN (ltem Code: SEBP 1112) or equivalent (only manual lockinq system)

Counter Communication System : Supply, installation, testing and commisioning of two way counter communication system including speaker, mike, control unit, power unit etc all required (make : Ahuja ccs 2300 or equivalent)

Water Dispenser: Supply and errection of water dispenser can hold 20 litre water bottle having normal standing design with 14 liter refrigerator at bottom and having 3 temperature taps hot, plain and cold. 3 liter cooling and 5 liter heating capacity per hour. Body made of ABS plastic and tank made of Food grade stainless steel. Heavy duty bottle piercer with bottle holder. with min 1 year warranty. (Make : voltas / Blue star/ equivalent)

Biometric Attendance System: Supplying, installtion, testing and commissioning of Biometric System with connectivity TCP/IP/RS232/Ethernet port supporting minimum 500 users with inbuilt RFID Card Reader, 10 No of RF ID Card and integration of the same with suitable attendance software. Make: CP Plus/ESSL/Matrix or equivalent

Supply of ABC Type fire extinguisher of 2 Kgs. Make SAFEX / MINIMAX / CEASEFIRE or equivalent