Forest Industries Travancore Limited Tender

4.1.8 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size)

7.1.1 : Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) up to plinth level with:Cement mortar 1:6 (1 cement : 6 coarse sand)

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.1.2 : Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

13.33.1 : Pointing on stone work with cement mortar 1:3 ( 1 cement : 3 fine sand):Flush/ Ruled pointing

13.1.1 : 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

13.43.1 : Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer

13.46.1 : Finishing walls with Acrylic Smooth exterior paint of required shade:New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

50.6.3.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x10 cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level for 10 cm thick wall in : CM 1:6 ( 1 cement : 6 coarse sand) including cost of scaffolding complete

od111066/2024_2025 : Providing and fixing 60x30x2 cm Granite stone block Flamed surface on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1 cement : 4 coarse sand) with joints filled with same mortar including ruled pointing etc. complete as per direction of engineer-in-charge.

od110998/2024_2025 : Supplying and fixing machine finished granite stone sitting bench of 1.5 m length, slab thickness not less than 50 mm, 450 mm clear height from ground level, 450 mm wide sitting slab, 450 mm wide back rest including cost of conveying, loading, unloading,material and labour charges etc. complete as per the direction of departmental officers.

16.86.1 : Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. complete as per direction of Engineer-in-charge.Area less than 0.50 sqm.

8.3.2 : Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer -in-Charge.Granite work

10.28 : Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.)

od111249/2024_2025 : Supplying and fixing Sign board size approximately 7mtr wide and 3.7 mtr height, metal frame , fabricated in ACP sheeet , Samsung 3 module LED Lights, etc. all complete as per direction by he Engineer in charege

od111267/2024_2025 : Designing and Fixing Inauguration/signage Board including cost of board, lettering, fixing, conveying etc all complete As per the Direction Of Departmental officers

OPEN GYM

od111273/2024_2025 : WALKER SINGLE- Providing and fixing Walker single- FNF 004 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe- for MAIN FRAME, minimum 32 NB GI B-CLASS Pipe- for LEG FRAME, Minimum 25 NB GI B-CLASS Pipe for HANDLE FRAME, NYLON 66 INJECTION MOULDED CASING CLAMPS, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" FOOT REST, Nylon 66 injection Moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111274/2024_2025 : STEP TRAINER- Providing and fixing Ski trainer - FNF 007 (Make FUN PLAY )using, Minimum 100 NB G.I. C CLASS pipes for MAIN FRAME, Minimum 40 NB G.I. pipe for FOOT REST PIPE, Minimum 40NB & 25 NB G.I. pipe for HANDLE, Minimum 25 NB & 40 NB GI B-CLASS Pipe for CONNECTING PIPE, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for FOOT REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111275/2024_2025 : CHEST PRESS CUM SHOULDER PRESS- Providing and fixing Chest press cum shoulder press - FNF 016 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for CENTER FRAME, Minimum 40 NB & 32 NB GI B-CLASS Pipe for MAIN FRAME, Minimum 32 NB & 25 NB GI B-CLASS Pipe for HANDLE FRAME, Minimum 32 NB & 25 NB & 40 NB GI BCLASS Pipe for CONNECTING PIPE, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for SEAT & BACK REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111276/2024_2025 : LEG PRESS- Providing and fixing Cycle - FNF006 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111277/2024_2025 : LEG EXTENTION- Providing and fixing Cycle - FNF020 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111278/2024_2025 : ONE SEATING CUM 2 STANDING TWISTER- Providing and fixing Tai chi cum twister - FPSPCL215 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for MAIN FRAME, Minimum 25 NB GI B-CLASS Pipe for HANDLE FRAME, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for TWISTER DISC, Minimum 25 NB & 20 NB GI B-class Pipe for SEATING FRAME, Minimum 80 NB GI B-class Pipe for SEATING FRAME STAND, Minimum 80 NB GI B-CLASS Pipe for TWISTER STAND, Minimum 25 NB GI B-CLASS Pipe for TWISTER HANDLE FRAME, LLDP Plastic- TWISTER DISC, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111279/2024_2025 : PENDULUM- Providing and fixing Pendulum - FNF 012 (Make FUN PLAY )using, Minimum 100 NB GI C-class Pipe for MAIN FRAME, Minimum 40 NB GI B-CLASS Pipe for LEG FRAME, Minimum 25 NB & 32 NB GI B-CLASS Pipe for HANDLE FRAME, LLDP Rotomoulded seat with inbuilt bolts 3/8" X 1.5" for FOOT REST, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111280/2024_2025 : CYCLE- Providing and fixing Cycle - FPSPCL208 (Make FUN PLAY )using, 25 NB & 40 NB GI B-class Pipe for MAIN FRAME, 32 NB GI B-CLASS Pipe for SEAT FRAME, 25 NB GI B-CLASS Pipe for HANDLE FRAME, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111281/2024_2025 : ABB TRAINER- Providing and fixing ABB Trainer - FPSPCL187 (Make FUN PLAY )using, Minimum 80 NB GI B-class Pipe for MAIN FRAME, Minimum 32 NB GI B-class Pipe for SIDE FRAME, Minimum 25 NB G.I. PIPES for INTERMEDIATE PIPE, Nylon 66 injection moulded BEARING CAP & PIPE CAP, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

od111282/2024_2025 : SHOULDER TWIRL NEW- Providing and fixing Bench with fix weight - FPSPCL247 (Make FUN PLAY )using, 100 NB G.I C-Class pipe for main frame, 32 NB G.I B-Class pipe for Bench frame, 20 NB G.I B-Class pipe for Handle frame, fully Done by first coat of Primer – jotun Brad 40-50 Micron thickness and Top Coat of pure polyester powder with 70- 80 micron thickness POWDER COAT including cost of concrete foundation , all materials, labour,etc all complete asper the instruction of Engineer in-charge

ELECTRICAL WORKS

2.4.1 : Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface / recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)4 way (4 + 12), Double door

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.12.1 : Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

2.14.2 : Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 amps

od111291/2024_2025 : Supplying and fixing 350x530 mm Post top Light (Classic Medium. Clear Diffuser. Material: Resin Moulded in black ) 15w Bulb etc all complete as per the direction of Engineer in charge

od111292/2024_2025 : Supplying and fixing following complete Cast Iron 2.5 mtr height ornamental pole , minimum weight 110kg, including the cost of conveying, loading, unloading, erection charge ,foundation bolt, plate, 2.5sqmm wire, etc all complete as per the direction of Engineer in charge

od111293/2024_2025 : Supplying and fixing outdor Pedestal type Feederpillar meter box made out of 16 gauge powder coated sheet with clear coat, fitted with 25 A 2P MCB Isolator ( 1no) , 32 A Fuse with HRC ( 1NO) 25A 2P 30 MA RCCB (1 no) MNX 9 2P contractor (1 no), 10 A SP MCB (3 no) , etc all complete as per the direction of Engineer in charge