Forest Industries Travancore Limited Tender

4.1.5 : Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

4.2.2 : Providing and laying cement concrete in retaining walls, return walls, walls ( any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts,buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc. up to floor five level, excluding the cost of centering, shuttering and finishing:1:11/2:3 (1 cement : 11/2 coarse sand :3 graded stone aggregate 20 mm nominal size)

5.9.1 : Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.9.2 : Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

5.22.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.22A.6 : Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more

50.6.2.2 : Solid masonry using pre cast solid blocks (factory made) of size 30x20x15cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level with thickness 15cm in : CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.2 : 12 mm cement plaster of mix:1:6 (1 cement : 6 fine sand).

60.7.1 : DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course masonry with good quality blasted rubble including packing to compactness to lines and levels cost and conveyance of all materials labour charges etc. complete as per direction of Departmental officers at site

60.7.8 : DR with Departmental. Stone - DRY RUBBLE MASONRY _ Dry rubble without concrete levelling course using departmental rubble including packing to compactness to lines and levels, labour charges etc. complete as per direction of Departmental officers at site

16.1 : Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

16.79 : Providing , laying spreading and compacting graded stone aggregate ( size range 53 mm to 0.075 mm) to wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, for all leads & lifts, laying in uniform layers with mechanical paver finisher in sub - base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to achieve the desired density, complete as per specifications and directions of Engineer - in- Charge.

16.91.2 : Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.80 mm thick C.C. paver block of M-30 grade with approved color design and pattern.

Finishing works

13.47.1 : Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade:New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

13.50.1 : Applying priming coat:With ready mixed pink or Grey primer of approved and manufacture on wood work (hard and soft wood)

13.52.1 : Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.On steel work

od120763/2023_2024 : Tile brick masonry with flower type brick Jally in superstructure above plinth level up to floor V level in cement mortar 1:6 (1 cement : 6 coarse sand)(from floor 0 level up to floor 5 level)

od202963/2023_2024 : Laterite tile (polished) work for wall decoration over existing bed of cement mortar and fixing it with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness including pointing in joint filler complete.<br>10 mm thick laterite tile<br>

12.45.3 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum moisture resistant board

Structural steel work

50.10.1 : Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

10.25.2 : Item Shifted to head 14 as item 14.74Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

51.20 : Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) 0.35 mm (+0.05%), total coatedthickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side. of the sheet and polyester top coat 15-18 microns.Sheet should have protective guard film of 25 microns minimum to avoid scratchesduring transportation and should be supplied in single length upto 12 metre or as desiredby Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws ofsize (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical orcurved surfaces, excluding the cost of purlins, rafters and trusses and including cutting tosize and shape wherever required.

od121878/2023_2024 : Providing and fixing pre-coated galvalume iron profile sheets (arch roof) 0.90 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 350 MPA steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Electrical works

90.3.19.3 : Supply conveyance, installation, testing and commissioning the light fittings of following types made from CRCA sheet 0.5mm thickness with all accessories and lamps directly on wall and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required

90.3.23.5.3 : Surface mounting decorative fluorescent tube light fitting complete with lamp with complete accessories duly wired up for use on 230 V AC .

90.3.23.5.4 : Surface mounting decorative fluorescent tube light fitting complete with lamp with complete accessories duly wired up for use on 230 V AC .

90.4.5.2 : Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.

90.4.8 : Charges for cutting holes suitable for accommodating exhaust fans up to 305mm sweep including plastering colour washing etc. as required.

90.4.9 : Charges for cutting holes suitable for accommodating exhaust fans above 305mm sweep and up to 450mm sweep including plastering colour washing etc. as required.

od122704/2023_2024 : Supply of 3 watt panel type round LED ceiling light<br>

od122705/2023_2024 : Supply, conveyance ,installation , testing and commissioning of !5 watt panel type round LED ceiling light with16/0.20mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connections etc. as required

od122706/2023_2024 : Supply, conveyance,installation,testing and commissioning the 12 watt Natural White / Warm White Mount Ceiling Lamp with 16/0.20 mm 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connections etc. as required.

od122707/2023_2024 : Supply of 220 Volts,15 Watt 6 inch Mounted Ventilation Exhaust Fan

Fire fighting works

od122477/2023_2024 : Providing, laying, testing & commissioning of 'B' class medium duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required: 100mm

od122535/2023_2024 : Supplying, installing and commissioning portable fire extinguishers of following type & capacity. The requirement shall be based on NOC & drawings. ABC stored pressure type fire extinguisher of 5 Kgs. capacity bearing ISI Mark for Fighting ABC & Electrical Class of Fire. The Extinguisher will be Manufactured Strictly as per BIS: 15683:2006 bearing ISI. mark. EN3 615 Approved Powder. ABC 87% MAP.

od122600/2023_2024 : Supplying, installation, testing & commissioning sector panel suitable for following zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections,<br>interconnections as required. 04 loop panel, Addressable fire alarm panel

od122601/2023_2024 : Supply, installation, testing & commissioning of Pressure gauges of suitable range with necessary fittings like unions / colors / reducers, siphon.

od122602/2023_2024 : Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete: 25 mm nominal bore

od122603/2023_2024 : Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100mm

od122604/2023_2024 : Providing, installation, testing and commissioning of non-return valve of following<br>sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :100mm

Miscellaneous works

od122259/2023_2024 : S.I.T.C OF 1 No. 8 PASSENGER MRL‐GLS ELEVATOR : Microprocessor based V3F ARD, 3 Stops and 3 Openings, S.S hairline finish cabin, Emergency light, emergency alarm, Over load indicator, antiskid PVC flooring, S.S hairline finish center opening doors with infra red safety etc including all standard features of passenger lift. Type of lift : Passenger lift (8 passenger) MRL ‐GLS, Load or persons:‐ about 544 Kg/8 passenger, Rated speed : 1 M/s. Travel : Approx 15 mtrs, No of floors served : 3 Floors 3 Openings (All openings same side), Method of control : Simplex collective selective, Size of lift well : 1900mm W 1970 D, Cabin size : 950mm W x 1500mm D, Drive : Variable Voltage Variable Frequency Door Operation, Power operated automatic ,car enclosure : Stainless Steel cabin hairline finish, Emergency light, emergency alarm, over load indicator,Antiskid PVC flooring, Power supply : 415 V Three‐phase 50 cycles AC, 230 V Single‐phase 50 cycles AC, Car Entrance : SS. Hairline Finish Door ,Automatic Center Opening Door, (900 mm W x 2000mm H), Landing Entrance : SS. Hairline Finish Door , Automatic Center Opening Door, (900 mm W x 2000mm H), Emergency Light, Emergency Alarm, Over Load Indicator, Fire man, switch, Automatic Rescue Device, Imported Face plate for landings call button., Imported Face plate for car call button., 147 Beams Infra Red Light Curtain for door Safety. (Imported)Digital floor Position and Direction Indicators in Car and Landings.

od122146/2023_2024 : HIGH WALL SPLIT-AIRCONDITIONER <br>Supply of non-ducted high wall split air-conditioning units comprising indoor units with three speed evaporator fan motor, fan, cooling coil and insulated drain pan enclosed in plastic casing complete with cordless remote control. <br>1.5 TR

od122427/2023_2024 : Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)<br>(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520<br>b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325.<br>(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.<br>(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.<br>450 lpm at 35 m Head

od204788/2023_2024 : Supply, Installation, Testing, Commissioning of 24 ft., anodized/ powder coated blades 1500 W HVLS Fan working on 3 phase, 415 V, 50 Hz supply of brushless DC technology, IP 64 Protection , class F insulation, >98% efficiency with reinforced bearing etc., speed controlled by VFD of suitable rating, operated through Key pad at approachable location having keys for starts / stop, reverse/ forward & speed increase/ decrease option, control panel with VFD along with top or bottom cable entries with detachable cable glands sheet etc. confirming to IP 42, power and control cable of suitable rating in PVC pipe as required ,blades (aluminum HE 9 grade having suitable ribs for extra strength, with internal wire rope wrapping to prevent fall out in case of blade breakage ) along with with hub (single piece die casted LM 6 aluminum grade material, radiography tested), tension wire, top safety ring , mounting rod, extension tube of stainless steel , metal guy wires, safety ropes, nut bolts etc. as required confirming to IS 2062 etc. as required as per site requirement.