Forest Department Tender

Reinforced cement concrete work in beams, suspended floors, roofs. having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with1:1.5:3 (1 cement : 1.5 coarse sand (Zone Ill) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+0.05%), total coated thickness with zinc coating 120 grams per sqm as per |S: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to uo avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling/self tapping screws of size (5.5x55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of |purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05%) total \coated thickness, zinc coating 120 grams per sqm as per !S:mm(+0.05%) total coated thickness, Zinc ല്‍ coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both ! ‘side of the sheet and polyester top coat 15-18 microns using self drilling/self tapping screws ) ‘complete:Ridges plain (500-600 mm)

Providing wood work in frames of doors, windows. clerestory windows and other frames, wrought framed | | and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs 00) | ,dash fastener shall be paid for separately), using good quality Anjili wood jack wood

Providing and fixing paneled and glazed shutters for doors, windows and clerestory windows, 35 mm | thick shutters including IS] marked M.S. pressed butt hinges bright finished of required size with : necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineerin - charge.using Anjili/ Jack wood

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm. 4 | ന്നേ out of extruded 5 mm rigid PVC foam sheet. mitred at corners and joined with 2 Nos. of 150 mm | | long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 | ‘mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the ! |frame. The door fame to be fixed to the wall using M.S. screws of 65/100 mm size. complete as per ) |manufacturer's specification and direction of Engineer-in Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and sized of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. | ' frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5! ! mm thick heat moulded PVC റ channel of size 30 mm thickness, 70 mm width out of whic) 50 mm shall; be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and ടന്ന thick. 95 mm! | | ) iwide PVC sheet out of which75 mm shall be tapered in 45 degree on th inner side to form top and bottom | | "a and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both: i | ‘sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5) mmx2) thick. 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail paneling of! 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded /sealed to the styles & rails with 7 mm (5mm + 2 ന്ന) thick x 15 mm wide PVC sheet beading on inner side, and joined together with | | solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior j side of the ൦ Channel using PVC solvent adhesive etc. complete as per direction of Engineer “in-charge,, 'manufacture's specification & drawing.30 mm thick plain PVC door shutters

Steel work in built up G | tubular ( round, square or rectangular hollow tubes etc.) trusses etc. including | |cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding land bolted with special shaped washers etc. complete

steel work for purlin/single section with G | pipes including cutting, hoisting, fixing in position and applying priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up | |Standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : | 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the | |gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. | ] |Aluminium sections shall be smooth, rust free, Straight, mitred and jointed mechanically wherever | jfequired including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel | | | screws, all complete as per architectural drawings and the directions of Engineer-in-charge (Glazing. | | |Paneling and dash fasteners to be paid for separately):For fixed portionPowder coated aluminium | [ ' (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making | | | provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket : | required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder | 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM] | rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer | | in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with ട്രി | ] land lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe. with manually canirolled! | | |device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and i : | j | imaking good the walls and floors wherever required:W.C. pan with |S] marked white solid plastic seat and lid

Providing and fixing wash basin with ൨. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste | | | standard pattern, including painting of fittings and brackets, cutting and making good the wails | | jwherever require:White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass : pillar taps

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws| ‘etc. complete:100x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS : 4992 with necessary screws | letc. complete:125 mm

Supplying and fixing 200 mm Aluminium aldrop

Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge

Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and Jabour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC pipes. fittings including fixing the pipe with clamps at 1.00 m spacing. This | includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as! | (per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. Ts | includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as ' iper direction of Engineer-in-Charge. Concealed work, including cutting chases and making good the wall etc. 20 mm pipe 10 Kgf/ cm2

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work. including cutting chases and making good the Wall | .etc. 50 mm pipe 6 kgficm2

Providing and fixing PVC pipes includings of pipes with one step PVC solvent cement, trenching refilling | | & testing of joints complete as per direction of Engineer in Charge. 63 mm dia 6Kgficm2

Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, | refilling & testing of joints complete as per direction of Engineer in CHarge. 110 mm dia 4 Kg/cm2

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with solvent cement - 63 mm dia Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC ; i jSolvent cement -63 dia 45 degree Elbow

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC | solvent cement - 63 mm dia Bend

Providing and fixing PVC moulded fittings’ accessories for Rigid PVC pipes. including jointing with PVC’ | | solvent cement - 63 mm dia vent cowl

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes. including jointing with PVE] | | solvent cement - 110 mm dia Elbow

Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC| | | solvent cement - 110 mm dia 45 degree Elbow

Providing and fixing PVC moulded fittings) accessories for Rigid PVC pipes. including jointing with PVC! | solvent cement- 110 mm dia Bend

Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with vel | solvent cement 110x110x110 mm dia Tee

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by ne | | | manufacturer). of 1st quality conforming to IS : 15622, of approved make. in colours such as White, Ivory. | | :Grey, Fume Red Brown. laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including; | | [pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) | ‘with water absorption less than 0.08% and conforming to 15 : 15622, of approved make. in all colours andi | | [shades laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the jints| | ‘with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm.

Providing and fixing brass bib cock of approved quality :15 mm nominal bore

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall | surface:Water thinnable cement primer

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work