Cooperative Academy Of Professional Education Tender

DIGITAL STORAGE OSCILLOSCOPE 100Mhz,Dual Channel,Colour Display, Bandwidth-DC~100Mhz(-3db),Rise time 5ns ,Bandwidth limit~20Mhz, Input coupling-AC, DC,GND Polarity-Normal & invert, Maximum input voltage: 300Vrms Vertical Sensitivity resolution -8 bit: 1mv~10v/div , Input Impedance~1MΩ DC gain accuracy-±3% Trigger mode:Auto,Normal,Single sequence ,Trigger type:Edge,Pulse width,video,external, rise & fall, timeout, alternate, Sensitivity:1 div, Event-delay(1~65535 events), time delay(duration~4ns~10s),Holdoff range:4ns~10s External Trigger Range:±15V Sensitivity:~100mv Input impedance:1MΩ Horizontal Time base range:5ns/div~100s/div Roll:100ms/div~100s/div ,Pre-trigger:10div maximum ,Post-trigger:2000000div maximum Time-base accuracy:±50ppm over any ≥ 1ms time interval ,Real time sample rate:1GSa/s maximum ,Record length:~10Mpts, Acquisition mode:Normal,Average,Peak detect,Single ,Peak detection:2ns ,X-Y mode phase shift:~±3° Cursors:Amplitude,Time,gating Unit:second, Hz(1/s), phase(degree), ration(%) automatic measurement:36 sets:pk-pk,max,min, amplitude,high,low,mean,cycle mean,rms,area,cycle area, rovshoot,fovshoot,rpreshootfpreshoot,frequency,period,rise time,fall time,positive width,negative width, duty cycle, positive pulse,negative pulses,+edges,-edges,FRR,FRF, FFR, FFF, LRR, LRF, LFR, LFF, phase

DIGITAL MULTIMETER Digital Multimeter with 3 ½ digit LCD Display DC Voltage : 0 – 200mV/2V/20V/200V/1000V AC Voltage : 0 – 200mV/2V/20V/200V/750V Dc Current : 0 – 200uA/2/20/200mA/10A AC Current : 0 – 200uA/2/20/200mA/10A Resistance : 0 – 200/2k/20k/200k/2000K/20M/200Mohms Diode test, hfe test, and audible continuity test facility

Bread Board 1680 tie points

DC Regulated Dual Power Supply (0 - 30) V,2A (0 - 30) V,2A. Continously variable by coarse and fine knobs. Metering : 3 digit DPMs for Voltage & Current Ripple & Noise : Less than 2mV rms Protection : Against Over Load & short CKT

8085 Microprocessor trainer kit with LCD display (MEMORY : RAM:8KB expandable to 32KB, Jumper selectable. EPROM : 8KB expandable to 32KB, Jumper selectable. INTERRUPTS:4 Nos of Interrupts are terminated in a 5-pin connector KEYBOARD AND DISPLAY :IBM -PC Keyboard (104 keys) 16 x 2 alphanumeric Dot SERIAL AND BUS EXPANSION:3 Channel 16 bit counter / timer terminated in a 10 Pin Connector. 48 TTL I/O Lines, terminated at 26 pin FRC connector On board 8 digital inputs can be given through 8 way Dip switch On board 8 digital outputs can be visible through 8 way SMD LEDs. Digital I/O Lines are terminated in 20-pin connector RS232C Compatible serial Port terminated in a 9 Pin "D" Male Connector. One VXT Bus (50 Pin FRC Connector) for interfacing BMB series of Experiment boards and bus expansion. crystal Display with back light TIMER PARALLEL I/O DIGITAL I/O SPECIAL FEATURES : Software single stepping of user programs by instruction for software debugging. Test points for all control signals are terminated at "Test Pins" for easy analysis on CRO or Logic probes. Housed in a sleek Plastic Cabinet.

D/A interfacing card Two numbers of DAC 0800 x Analog Output: +5V to -5V x DAC outputs are terminated at a suitable connector available on*board x Provision for test points & fault analysis points * All Address, data and control lines are terminated in a 50 Pin FRC OEN "make male connector to interface with VXT bus * 50 Core Cable provided

A/D interfacing card Incorporates one number or ADC 0809 * Start of Conversion by manual switch or software * End of Conversion (EOC) monitored through Interrupt / Polling * Display of digital data using LED's * All the 8 channel analog inputs terminated at Screw type connector. * Trimpot is provided on-board to channel 0 or 3or6 * Provision for test points & fault analysis points x 50 Core Cable provided * All Address, data and control lines are terminated in a 50 Pin FRC OEN Make male connector to interface with VXT bus

Arduino Uno Arduino Uno R3 ATmega328P ATMEGA16U2 Compatible with USB Cable

8086 trainer kit 16*2 lcd display CPU 8086 (16 BIT PROCESSOR) -CLOCK 6.144 MHZ KEYBOARD PS/2, IBM -COMPATIBLE -DISPLAY 16* 2 LCD MODULE RAM 16KB (6264 *2) -EPROM 16KB (2764 *2) -IO LINES – 48 LINES USING 2 NOS OF 8255 -TIMER/COUNTER 8253 -INTERRUPT CONTROLLER 8259 -INTERFACE UART(8251) BUS50 pin FRC (TTL COMPATIBLE) -INPUT SUPPLY 230V,A.C, 1 PHASE, +/10%, 50 HZ -DC SOURCE + 5V ,1 AMPS;+/12V