Urban Development Authority Tender

026 - Providing, Supplying and Fixing, Installation, Commissioning and Trail run of childern Play Equipment Supply & fixing of children multi play equipment with spiral slide, monkey bar with number pannel Upright structural posts of height 2.3 m, 2.6 m and 3.2 m are to be schedule galvanized steel with a 114 mm OD deck of size 1.16m x 1.16 m and staircase of size 1.0m x 0.60m shall be in an all robotic welded assembly fabricated from perforeted solid punched steel. Deck perimeter is precision pre pucnched for attachments, Decks are prepressed, punched and welded, powder coated to 2.2 mm thick ness or vinyl plastick coated to a thickness of 4mm Handrail of height 1.88m & Dia 32 mm shall be an all robotic welded unit, fabricated from 32 0.D. galvanized steel pipes. Snake Climber, Piped walls of sim 2.14 m shall be an all robotic welded fabricated from 320.0 galvanized steel pipes for the outer pipes and 25 mm D.D galavanized steel for the inner parllel bars, Roof of size 1.47 m x 1.47mx0.96 m, Wavey Slide of size of 2.38 m x 0.55m x 1.20 m Top rails of Monkey Bar of Size 2.32x 1.0m & Swing of size 2.55 m x1.16 shall be fabricated from 32mm O.D galvanized steelpipe. Bolts, Nuts, Screw, Washers and etc used for assembly shall be stainless stell 304 grade and shall be of tamper resistant stainless steel Exposed Hardware shall be covered with safty caps as a saftey. All joints are robotic welded all components meet with EN-1176 Saftey Standards. PLAY EQUIPMENTS DIEMENSIONS 17.44m x 4.03m x 3.81m

001 - Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m.

014 - Providing and laying Pitching on slopes laid over prepared filter media including boulder apron laid dry in front of toe of embankment complete as per drawing and Technical specifications. A Stone/Boulder

055 - Brass Cable Gland . 25 mm

048 - Laying of cable in Existing Trench/GI pipe/ Stoneware/RCC Hume pipe using wooden/ Aluminium Rollers as directed by department staff. LT Cable . 35 to 95 Sqmm

037 - Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50 Hz AC with latest microcontroller based, digital readout of percentage leakage current, programmable delay/auto/ manual reset facility suitable to mount on DIN rail/ flush mounting on panel board

004 - Providing new embankment abutting to existing bund to strength the existing bund using soil from approved borrow area in layers of 200 to 250 mm and compacting each layer to density control of not less than 95 percent by vibrating plate compactor or pnuematic tamper including cost of all materials, machinery, labour, picking previous layer, spreading soil in layer, breaking clods, watering & all necessary works as directed and complete as per specification.

025 - Providing, Supplying and Fixing, Installation, Commissioning and Trail run of childern Play EquipmentSupply & fixing of children multi play equipment: Supply & Fixing of Multi Play System 514: All productsmust be tested and certified to meet EN 1176 safety standards. The EN-1176 cortificates must be issued by a reputed notified international Certifying Body such as (PEMA, TUV, CPSC, or 565 anly, These IN 2176certificates must be clearly displayed on the notified certifying bodies websites as online verification mandator Upright structural posts of height 2.3 m, 26 m and 2.9 m are to be schedule Galvanized steelwith a 114mm OD (Outer Diameter). Deck of size 1.16mx1.16 m & Staircase of size 1.00 m 0.66mshatibe an all-ROBOTIC welded assembly fabricated from perforated solid punched steel. Deck erimeterprecnion pre pun ched for attachments. Decks are pre pressed, punched& welded, powder coatedto 2.2mm thickness or vinyl plastic coated to a thickovess of 4mm. Handrail of height 1.89 m and Dia 32imm shall be an alirobotic welded unit, fabricated from 32 0.D galva nized steel pipes. Roof of size 1.47 mx 1.47 mx 0.96 m. Tube Slide of size 3.21m x 0.99m x 1.20 m. Doubin Slide of size 2.06m x 1.69 m x 0.90m, Straight Slide of size 1.68 m x 0.66mx 0.90 mc Swing of size 2.55 mx 1.16 m shall be fabricated from32mm 0.0. galvanized steel pipe Bolts, nuts, screws, washers and etc used for assembly shall bestainless steel 304 grade and shall be of tamper resistant stainless steel Exposed hardware shall be covered with safety caps as a safety. All joints are Robotic welded. ALL COMPONENTS MEET WITH EN1276 SAFETY STANDARDS, PLAY EQUIPMENT DIMENSIONS: 6.75 m x 6.43 mx 3.70m The work includesall other incidental works required to complete the work in all respects for smooth functioning of theequipment at all times in all respects for its intended use. The works required in fixing the equpment onsite as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machineryets, required to complete the work. As per the direction of Engineer-in-charge

031 - Supplying of on load change over switches 4 poles, AC-23ADuty, 415V, 50Hz, AC Supply. (Open Execution) 100 A

027 - Providing, Supplying and Fixing, Installation, Commissioning and Trail run of childern Play Equipment Supply & fixing of children multiplay equipment: Supply & fixing of childern Multi Play Equipment with double wing, curved side toddler slide with animated roof Upright structural posts of height 2.7 m & 3 m are to be schedule HOT DIP Galvanized steel with a 114mm 00 and 2.2 mm (wall) thickness of the tubing The poles are welded on to a base plate made from steel with 114mm inner diameter. Deck of size 1.45x 1.45m and Staircase of size 1.48 m x 0.60 m are fabricated from 2mm perforated solid punched steel Deck perimeter is precision pre punched for attachments. Handrail of beight 1.90 m and Dia 22 mm shall be an all-robotic welded unit, fabricated from 32.0.0. galvanized steel pipes with a baked powder coating finish, Exposed hardware shall be covered with ultra violet stabilized plastic safety caps as per Sun Roof of size 2.0 mx 1.78 mx 0.77m, Spiral Slide of size 2220 mm x 1630 mm x 1880 mm, Straight Slide of size 1645 mm x 500 mm x 1140 mm, Panels. Roofs and panels are copyrighted and IP protected world wide. Spring Climber of thickness Dia 38 mm, 3 step ladder, Frisbee Climber Piped walls of Height 2.7 m are all robotic welded fabricated from 32 O.D. galvanized steel pipes for the outer pipes and 25mm 0.D. galvanized steel for the inner parallel bars with a baked on powder coat finish. The rates are to be inclusive of supply and installation at site. Inclusive of All Taxes and Transportation Charges

028 - Supplying of Switch disconnector fuse unit (TPN) HRC type(but without HRC fuses). With AC-23A duty and as per IS-13947. 63Amps

041 - Supplying, fixing, wiring, earth electrode for grounding conduits, I.C.cutouts and other equipment's on the meter board using 40 mm dia 2.90 mm thick GI pipe 2.5m long buried in a pit . The pit should befilled with equal proportion of salt and charcoal 150 mm all-round the pipe to complete depth. The connection from the pipe to the conduitetc. , is to be established through GI wire of size as per lSI specification7.3.3. of IS 732 using 12 mm dia bolts, nuts, washers and check nuts etc., the pipe shall have 16 through holes of 12 mm dia

044 - Supplying and fixing hylum plastic sheet 3mm thick with necessary nitches for fixing switches, regulators etc., and fixing on existing wood or metal box using N. F. screws Hylam Sheet Dimension 75cm x 75 cm =5625 sqcms

024 - Providing, Supplying, fixing, installation, commissioning and trial run of Hexa Climber Supply and Fixing of Hexa Climber: All products must be tested and certified to meet EN 1176 safety standards. The EN 1176 certificates must be issued by a reputed notified International Certifying Body such as IPEMA, TUV, CPSC, or SGS only. These EN 1176 certificates must be clearly displayed on the notified certifying bodies websites as online verification is mandatory. Upright structural posts of height 2.3 m, are to be schedule Galvanized steel with a 114 mm OD (Outer Diameter), Parallel Climber of size 1.9mx 1.17 m, Horizontal Ladder 1.9 m x 1.17 m, Pull up Bar, Chain climber of size 1.9 m x 1.1 m, and Gymnastic Rings of size 0.77 m x 1.17 m shall be an all patent welded fabricated from 54 mm O.D. galvanized steel pipes. Bolts, nuts, screws, washers & etc used for assembly shall be stainless steel 304 grade & shall be of tamper resistant stainless steel. Exposed hardware shall be covered with safety caps as a safety. All joints are Robotic welded, PLAY EQUIPMENT DIMENSIONS: 2.2 m x 2.1 mx 2.3 m The work includes all other incidental works required to complete the work in all respects for smooth functioning of the equipment at all times in all respects for its intended use. The works required in fixing the egiupment on site as per the site condition. The cost includes, cost of transportation, cost of labour, HOM of machinery etc., required to complete the work. As per the direction of Engineer-in-charge

020 - Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

029 - Supplying and fixing HRC fuse units base on existing switch/ panel board 32 to 63 Amps

015 - Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.

043 - Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers. 32 Amps

030 - Supplying and fixing HRC fuse link on existing switch fuse base with watt loss as per IS-13703. Up to 63Amps

039 - Supplying and fixing angle iron frame work fabricated out of M.S. angle iron. and M.S. flat … with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. 40x40x6mm

033 - Supplying . amps rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/ FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete. 250Amps 4x30 x 10 MM Aluminium strips

038 - Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440v A.C. 50 Hz 12/24v D.C

013 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/ welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification. All other type of structures.

011 - Percentage Additionalities for Formwork, Centering & Scaffolding. RCC Beams, Lintels & Troughs of Aqueducts 60%

021 - Supply of JMS Casacade fountain aeration system 1.5 HP with Floats panel Board and accessories for improving water quality and beautification inculding installation charges,cost of wiring and transportation

007 - Percentage Additionalities for Formwork, Centering & Scaffolding. Earth retaining structures 10%

035 - Supplying and fixing Electronic Trivector Meter(ETV) suitable for operation LT operation and -CT operated meter in polycarbonate body in class 0.5 accuracy as per IS 14697 and completely wired.

010 - Percentage Additionalities for Formwork, Centering & Scaffolding. RCC Columns / Shaft (Slip Centering) 70%

042 - GI/Copper strips for grounding connections, using necessary fixing materials as required. 25 x 3 mm GI strip

051 - Aluminium End Terminal (Lug) . 32 Sqmm

017 - Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives with pure Acrylic Resin, UV resistant, dirt & pick up resistant, Alkali & Water resistant of required shade: New work (Two coats applied @ 1.43 L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

016 - Providing 18 mm cement plaster in two coats under layer 12 mm thick cement plaster with cement mortar 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster with cement mortar 1:6 (1 cement : 6 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge.

022 - Suppling and instalation of 25mm EPDM Flooring. Incluiding transporation, Loading, Unloading complite as per specification

034 - Supplying, fixing and wiring 3 Phase Digital Ammeter / Voltmeter

040 - Fabricating supplying and mounting MS box made out …SWG suit able for floor / wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrange ments, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete. 16SWG 1) 120cmx120cmx2 = 28,800 Sq.cm 2) 120cmx30cmx2 = 7,200 Sq.cm 3) 120cmx30cmx2 = 7,200 Sq.cm Total = 43,200 Sq.cm 1 Box x 43,200 Sq.cm = 43,200 Sq cm

036 - Supplying, fixing and wiring 50/5 to 400/5Amps 5VA burden Current Transformer. Class 0.5 accuracy with Tape Wound

006 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates.

009 - Percentage Additionalities for Formwork, Centering & Scaffolding. Piers & Abutments 10%

023 - Providing, Supplying, fixing, installation, commissioning and trial run of Sea saw Double-LK-SS-63, All Round & rectangular pipes are GI Or CR,ISI, make Guage 14 guage, 2coating are red oxide and final paints of industrial paint, Nut bolt Gl, Bearing heavy, (Branded.)FRP thickness 4-5mm, Swing assembly 6mmchain with rubber coating Length-8Ft, Width-5Ft, Hiegth-2 Ft., The work includes all other incidentalworks required to complete the work in all respects for smooth functioning of the equipment at all timesin all respects for its intended use. The work includes all other incidental works required to complete thework in all respects for smooth functioning of the equipment at all times in all respects for its intendeduse. The works required in fixing the eqiupment on site as per the site condition. The cost includes, costof transportation, cost of labour, HOM of machinery etc., required to complete the work. As per thedirection of Engineer-in-charge.

008 - Percentage Additionalities for Formwork, Centering & Scaffolding. Foundation upto Plinth a. Isolated 8%

018 - Providing and laying with burnt stone slabs 10 cm thick rough chistle dressed on sand bed 7.5cm to 8.0 cm thick, and pointed with cement mortar 1:3, including cost of materials, mortar, labour, curing complete as per specification

053 - Supplying and flush mounting teak wooden box without front plank, made of not less than 12 mm thick wood, after due groove cutting, finishing with necessary cement plastering complete. 12" x 12" x 3" (300 x 300 x 76 mm)

003 - Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

032 - Supplying and fixing Moulded Case Circuit Breaker (MCCB) over theexisting wood/ panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection ofOverload and Short circuitwith adjustable thermal magnetic release,Micro processor release shall have Earth Fault as per IS/IEC 60947-2 (Icu=100% lcs). In 4P MCCB, all Poles should have protection for Short-Cicrcuit/Over Load. For Microprocessor MCCBS Facility forsegregating Priority and Non-Priority loads must be available in theMCCB. MCCB shall be provided with double insulation (insulationbetween front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open). Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism.THREE Pole125Amps 25kA.

052 - Supplying heavy gauge PVC conduit pipe . dia . mmthick confirming to IS 2509 with suitable size bends, junctionboxes, adhesive paste etc , and fixing using inverted woodplugs in case of RCC ceiling and RCC wall/ stone structure or rawl plugs in case of brick walls and cement plastering the damaged portion using heavy gauge saddles at an interval of 700mm using NF screws. 40 mm dia 2.5 mm thick

047 - Laying of cable in Existing Trench/GI pipe/ Stoneware/RCC Hume pipe using wooden/ Aluminium Rollers as directed by department staff. LT Cable .2.5 to 25 Sqmm.

050 - Aluminium End Terminal (Lug) . 16 Sqmm

002 - Earth work excavation for Foundation by mecha nical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In all kinds of soils Depth upto 3 m.

045 - 1.1Kv XLPE or Heat resistant PVC insulated, PVC Extruded Inner sheath Armoured LT UG cable as per IS-1554(part-1 )or IS-7098 Part 1,Armouring strip thickness and resistivity as per IS-3975 . 16 Sqmm, 4 Core, (11 GI Strips - 4 x 0.8 mm).

046 - 1.1Kv XLPE or Heat resistant PVC insulated, PVC Extruded Inner sheath Armoured LT UG cable as per IS-1554 (part-1 )or IS-7098 Part 1, Armouring strip thickness and resistivity as per IS-3975 . 35 Sqmm, 3.5 Core, (14 GI Strips - 4 x 0.8 mm)

005 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, & all the other appurtenances required to complete the work as per technical specifications.Mix 1:3:6 Using 40 mm nominal size graded crushed coarse aggregates.

054 - Epoxy Terminating Kit (Pothead) suitable for 1.1 kV, LTUG Cable .Up to 4C x 50 Sqmm