Urban Development Authority Tender

code04 - Supplying and fixing polished wood board made of not lees then 15mm thick plank on both side with planks made out of more then 2 pieces and fixing the same to the wall using taperd inverted wooden flugs screws etc. 15 12" 2" (P No 14 No 5.6.5)

code05 - Supplying & fixing of Porcelain fuse channel with cut bout on existing wooden/panel using necessary nuts, bolts, and washers etc.. complete..63A Amps (P.No.14, 1.No.5.7.3)

code06 - Supplying & fixing of Porcelain fuse channel with cut bout on existing wooden/panel using necessary nuts, bolts, and washers etc.. complete..100A Amps (P.No.14, 1.No.5.7.4)

code07 - Supplying and fixing HRC fuse units base on existing switch /panel board. 100 Amps to 300 amps (P.No. 15, 1.No. 5.9.3)

code08 - Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Short circuitwith adjustable thermal magnetic release, Micro processor release shall have Earth Fault as per IS/IEC 60947-2 . (Icu=100% lcs). In 4P MCCB, all Poles should have protection for Short-Cicrcuit/Over Load. For Microprocessor MCCBS Facility for segregating Priority and Non-Priority loads must be available in the MCCB. MCCB shall be provided with double insulation (insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open). Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism FOUR POLE. 160 Amps 25KA. (P.No. 17, I.No.5.15.11)

code09 - Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C. (P.No 19, I.No. 5.38)

code10 - Supplying amps rated 3phase with neutral busbar using requiemed capacity electrolytic aluminium strips covered with heat shinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S. flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete.100Amps 4x30x6mm Alluminium Strips. (P No 20:1 No 5.40.1)

code11 - Supplying and fixing angle iron frame work fabricated out of M.S angle iron.. And M.S flat....with bolts. washers etc.. And painted with 2 coats of red oxide and then two coats of approved paint 50x50x6mm. (P No 20 1 No 5.41.2)

code12 - Supplying and fixing of Microprocessor based Electronic timer (without contactor, Din Mounting using necessary bolts, nuts and washers etc..) 3 -120sec. (P No 21; 1 No 5.47).

code13 - 1.1 kV, XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS-1554 (Part1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975-35 Sqmm, 4 Core,. (P No 13; I No 32.10)

code14 - Supplying, fixing & wiring, earth electrode for ground conduits. I.C. cutouts and other equipements, on the meter board using 40mm dia 2.90 thick of Gl pipe 2.5 mtr long burid in a pit. The pit sholud be gilled with equal pro[ortion of salt and charcoal 150mm alround the pipe to completedepth. The connection from the pipe to the conduit etc., is to be established through Gl wire of size as per clause 7.3.3 of is 732 using 12mm dia bolts, nuts, washers, & check nut etc., The pipe shall have 16 through holes of 12mm dia.(P.No.40.I.No.1)

code15 - Earth work excavation for pipelines/cables by Manual means upto 600 mm trench width, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, including dressing of excavated surfaces, disposing off or leveling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m. Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering and lift upto 1.5 m including cost of labour, tools, usage& other appurtenances required to complete the work (CSR-2023-24, Vol-1 I.no-1.6.1 & Pg No -6)

code16 - KSRB 13 - 9.1 : Providing and fixing to wall, Ceiling and floor HIGH DENSITY POLYETHYLENE PIPES ( HDPE ) 6 kgf/sq.cm Working Pressure 32 mm Outside diameter with special flange, compression type fittings, wall clips, making good the wall, ceiling and floor, including cost of all materials, labour charges, HOM of equipments and testing complete as per specifications. Including Rope For Tying of Borewell Sub-Mersible Motor etc complete. Specification No. KBS 13.2.15.2 / 13.9 ( P.NO-96 / I NO-13.71 )

code17 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately)-M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates & formwork shall be added on Percentage basis to the finished rate of concrete per meter cube

code18 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output Rated life Burning Hrs 50000 hr at Lumen Maintenance of 70percent, maximum light intensity should be between 60 degrees to 70 degrees. CCT great 5500K, IP66 optical and electrical compartment & impact resistance of complete luminaire great IK08. Power Factor great 0.9 with mains, Surge Protection Min 5KV along with Over voltage or Overload, short circuit or miss wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50 or 60Hz application. Compliance to IS 10322 or IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with W System Power consumption. LED Efficiency great 1301m or w, nominal CRI great 75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned - LED Streetlight 70W(P No 46 I No 11.8.3)

code19 - Supplying and Fixing of........mm dia class A GI pipe bracket upto 2 ms long bent at suitable angle and fixing to this bracket 1x40/2x40 W fluorescent tube street light fitting of all capacities to GI or GI or rail or RCC pole / wall using suitable clA, bolts, and nuts and wiring using suitable capacity wires - Using 32mm dia G.I.Pipe(P No 56; I No 13.1.2)

code20 - Fabricating, supplying and erection f ...ms long hot dip Galvanized Octagonal hot dip Pole with BSEN10025 grade S355JO steel plat for shaft, IS2062 for base plate with door opening arrangements, including suitable boards, Bakelite sheet and MCBs as per IS specifications suitable to with stand the wind speed of 47m/sfor.......m Pole in single section and single joint welded as per IS 9595/IS10178A WS having dimensions bottom.....mm, top....mm with 3mm thick,suitable base plate and 4Nos of..... long J bolts along with template and the Pole shall be hot dip galvanized in single dipping with not less than 65 micronas per ASTM A123 and 153etc., (excluding foundation) as per drawing appended. -9 m - Top 70 mm and Bottom 155 mm dia (P No -11 I No 4.2.5)

code21 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material, delivering superior light output Rated life Burning Hrs 50000 hr at Lumen Maintenance of 70percent, maximum light intensity should be between 60 degrees to 70 degrees. CCT great 5500K, IP66 optical and electrical compartment & impact resistance of complete luminaire great IK08. Power Factor great 0.9 with mains, Surge Protection Min 5KV along with Over voltage or Overload, short circuit or miss wiring protection. Compatible for pole mounting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50 or 60Hz application. Compliance to IS 10322 or IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with W System Power consumption. LED Efficiency great 1301m or w, nominal CRI great 75. Luminaire manufacturer should have in-house facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008. Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned LED Streetlight 120 W (P No 46 I No 11.8.5)

code22 - Supplying, and fixing of Hot dip Galvanized M.S.Bracket suitable for out door luminaries and mounted on Octagonal pole using necessary bolts, nuts etc., complete.(P No 13; I No 4.6.3)

code23 - Electrical Miscellaneous items such as 10 sqmm wire , Lux & 2.5sqmm wire others..etc Lux & 2.5 sqmm wire