Urban Development Authority Tender

2.4.2 - Providing and laying in position Reinforced cement concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necesary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates Including Centring charges

8.34.2 - Applying priming coat: With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood including preparing the surface after thorougly cleaning oil, grease, dirt and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

8.44 - Floor painting with floor enamel paint of approved brand and manufacture of required colour to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

1.1 - 9 MTR decorative curve street light pole With Top :75mm ,Bottom :190mm of 3mm pole thickness having two arm brackets fixed to it with one side facing to road and another to the footpath side for led street light fixtures. Baseplate : 300mm x 300mm x 16mm Foundation bolt: M24 x 750mm "J" Bolt of 4 nos/pole The pole will be thoroughly cleaned and painted with coat of PU surface primer and suitable PU Paint.

11.8.2 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body foroptimalthermaldissipation.Lamp compartment comprising of antiglare clear diffuser with Injection moulded polycarbonate material,delivering superior light output Rated life Burning Hrs50000hr Lumen Maintenance of 70, maximum light intensity should be between 60 degrees to 70 degrees. CCT 5500K, IP66 optical and electrical compartment & impactresistance of complete luminaire IK08. Power Factor 0.9 withmains,SurgeProtection Min 5KValong with Over voltage/Overload, shortcircuit/miss wiring protection.Compatible for pole mounting without er dia of 40mmto50mm. Universal Voltage driver to operate wide voltage range from 100Vto270V50/60 Hzapplication.Compliance to IS10322/IEC60598,LM79&LM 80 Adherence with RoHS UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools.LED Light fixture with WSystem Power consumption.LED Efficiency 1301m/w, nominalCRI 75. Luminaire manufacturer should havein house facility accredited by NABL/CPRI & any Government certified agency and Design and Development facility certified byISO9001:2008. Housing with supplier wordmark /name shall be Engraved/Embossing on the die cast housing/Body part. Warranty of 2Years against any manufacturing defectworking under standard electrical conditions as mentioned above should be given by LED manufacturer &Cree/Nichia/Lumileds/Osram make LED Source.LED Streetlight 40W

11.8.6 - Supply of LED Streetlight luminaire with pressure die cast aluminium housing body foroptimalthermaldissipation.Lamp compartment comprising of antiglare clear diffuser with Injection moulded polycarbonate material,delivering superior light output Rated life Burning Hrs50000hr Lumen Maintenance of 70, maximum light intensity should be between 60 degrees to 70 degrees. CCT 5500K, IP66 optical and electrical compartment & impactresistance of complete luminaire IK08. Power Factor 0.9 withmains,SurgeProtection Min 5KValong with Over voltage/Overload, shortcircuit/miss wiring protection.Compatible for pole mounting without er dia of 40mmto50mm. Universal Voltage driver to operate wide voltage range from 100Vto270V50/60 Hzapplication.Compliance to IS10322/IEC60598,LM79&LM 80 Adherence with RoHS UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools.LED Light fixture with WSystem Power consumption.LED Efficiency 1301m/w, nominalCRI 75. Luminaire manufacturer should havein house facility accredited by NABL/CPRI & any Government certified agency and Design and Development facility certified byISO9001:2008. Housing with supplier wordmark /name shall be Engraved/Embossing on the die cast housing/Body part. Warranty of 2Years against any manufacturing defectworking under standard electrical conditions as mentioned above should be given by LED manufacturer &Cree/Nichia/Lumileds/Osram make LED Source.LED Streetlight 150W

5.14.3 - Supply and fixing of 4 pole power contactor with NO/NC contacts on existing wood panel board using necessary bolts, nuts, washers and wiring etc., complete with AC-3 Rating and as per IS -13947. 40 A

5.15.2 - Supplying and fixing Moulded Case Circuit Breaker(MCCB)over theexisting wood/panel board using necessary screws, bolts, nuts, necessary phase separators,handle and wiring complete.Protection of Overload and Short circuit with adjustable thermal magnetic release,Microprocessor release shall have Earth Fault as per IS/IEC60947-2.Icu=100 lcs. In4PMCCB, all Poles should have protection for Short-Cicrcuit/OverLoad. For Microprocessor MCCBS Facility for segregating Priority and Non Priority loads must be available in the MCCB.MCCB shall be provided with double insulation insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open. Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism 125 A 25 kA

5.41.2 - Supplying and fixing angle iron frame work fabricated out of M.S.angle iron.and M.S.Flat.with bolts,washers etc.,and painted with 2 coats of red oxide and then two coats of approved paint.

2.5.9 - Supplying and drawing Flexible Multicore Cable manufactured with electrolytic grade flexible copper withlow conductor confirming to IS 8130 1984 and (Virgin) PVC insulation sheathed suitable for working voltage upto 1100 Volts as perI S-694:1990 4C x 2.5 mm2

5.47 - Supplying and fixing Microprocessor based Electronic timer (without contactor,DinMountingusingnecessarybolts,nutsandwashersetc.,.)3120sec setting.

5.42.1 - Fabricating supplying and mounting MS box made out .SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover,equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete-14 SWG

5.18.1 - Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicatorON/OFF,energycross-3 with Short circuitbreaking capacityof10Kandcomplete wiringas requiredconfirmingtoIEC 60898. 6-32 A SP

6.4.1 - supplying of 1.1 kv , LT UG, cable having alluminium conductor PVC insulted, extruded inner sheated, galvanised , steel strip ( except 2cX 10 sq. mm wire armoured) conferming to IS-3975: 1990(No of strip indicated in GTP) & extruded PVC outer sheathed armoured cable with specified IS-1554 part-1:1998 & conferming to GTP of GROUP-A

12.24 - Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe / stone were pipe/on wall/ on pole as required.

6.6.2 - Digging of trench of 0.6m deep x 0.50 m wide refilling the trench to the required ground level and consolidating etc complete as per civil SR KSRB I-2, P-7) insoll ( Hard)

6.7 - providing and filling sand in excavated trench to cover already laid UG cable to a depth of 150mm all-round the cable.

1.1.4 - Open conduit system supplying heavy guage PVC conduite pipe 40mm dia 2.5mm thick confirming to IS 2509 with suitalb size bends , junction boxes adhesive paste etc and fixing using inverted wood plugs in case of RCC ceiling and RCc wall / stone structrue or rawl plugs in case of brick wall adn cement plastering the damaged portion using heavy guage saddles at an interval of 700mm using NF screws.

6.17.8 - Supplying tinned copper lugs and crimping and wiring to terminal point for wire of the following sizes. (PWD Electrical SR 2019-20, P.No.43, I.No.6.17.8)

5.7.3 - Supplying & fixing of Porcelain fuse channel with cut out on existing wooden/panel using necessary nuts, bolts and washers etc., complete. 63A.

1.1 - Electrificatin and service wire and deposit charges