University Of Agricultural Sciences Tender

ITEM4 - Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and c type cirve, indicator ON OFF, energy cross 3 with short circuit breaking capacity of 10 K and complete wiring as required confirming to IEC 69898 Page No 17. Item No 5.18) 2023-24 6-32A SP

ITEM5 - 40 A TPN

ITEM6 - 1.1 kV XLPE or Heat resistant PVC insulated, PVC exutruted Inner Seath Armoured LTUG Cable as per IS 1554 (Part-1) or IS-7098 Part-1, Armouring strip thickness and resistivity as per IS-3975 (Bescom 11Kv Page no.-13 Item No-32.15) ESCOM 2023-24 120 Sqmm, 3.5 Core, (23 GI Strips - 4 x 0.8 mm)

ITEM7 - Labour charges for laying of 1.1 KV class UG cable in existing trench GI pipe stoneware pipe on wall on pole as required.(Page no.-68. Item No-7.8) 2014-15 In existing trench duct. 95 sqmm to 150 sqmm

ITEM8 - Digging of trench of 0.6m deep x 0.50 mtr wide refiling the trench to the required ground level and consolidating. ( Page No-68. Item No 7.9).vIn soil (hard)

ITEM9 - Rod Earthing : Rod type of earthing using 40 mm Dia, 3 Mtr long MS rod as ground rod, in earth pit of 300 mm width and 3300 mm depth and using 50x6 mm flat welded to ground rod as terminal and connected to equipment ground terminal using PVC Al wire as specified (Page no 23.-. Item No-51.04) ESCOME 2023-24

ITEM10 - Supplying of Switch disconnector fuse unit (TPN) HRC type (but without HRC fuses). With AC-23A duty and as per IS- 13947. (Page no.15 Item no.5.8) 2023-24 a) 160 A

ITEM11 - Supplying and fixing HRC fuse units base on existing switch panel board. (Page no.15 Item no.5.9) 2023-24 a) 100 to 300 A

ITEM12 - Supplying and fixing HRC fuse link on existing switch fuse base with W loss as per IS-13703. (Page no.15 Item no.5.10) 2023-24 A) Above 63 A to 200 A

ITEM13 - Supplying of on load change over switches 4 poles, AC-23A Duty, 415V, 50Hz, AC Supply. With all accessories. (SM Enclosure Sheet Metal Execution). (Page no.15 Item no.5.12) 2023-24 a) 200 A

ITEM14 - Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Short circuitwith adjustable thermal magnetic release, Micro processor release shall have Earth Fault as per IS/IEC 60947-2 . (Icu=100% lcs). In 4P MCCB, all Poles should have protection for Short-Cicrcuit/Over Load. For Microprocessor MCCBS Facility for segregating Priority and Non-Priority loads must be available in the MCCB. MCCB shall be provided with double insulation (insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open). Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism. (Page no.15 Item no.5.15) 2023-24 FOUR Pole 160 A 25 kA

ITEM15 - Supplying and fixing angle iron frame work fabricated out of M.S. angle iron.. and M.S. Flat with bolts, washers etc., and painted with 2 coats of red oxide and then two coats of approved paint. (Page no.20 Item no.5.41) 2023-24 75 x 75 x 6 mm

ITEM16 - Supplying A rated 3phase with neutral bus bar using required capacity electrolytic aluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary bolts, nuts and washers etc., complete (Page no.20 Item no.5.40) 2023-24 250 A 4 x 30 x 10 mm Aluminium Strips

ITEM17 - Fabricating supplying and mounting MS box made out SWG suitable for floor wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete.(Page no.20 Item no.5.42) 2023-24 16 SWG

ITEM18 - Supplying, fixing and wiring 0 to 600V 96x96mm AC Voltmeter on existing panel wood board. (Page no.18 Item no.5.22) 2023-24

ITEM19 - Supplying, fixing and wiring 0 to 100 A Direct Reading AC analog type Ammeter (Page no.18 Item no.5.25) 2023-24

ITEM20 - Supplying, fixing and wiring rotary selector switch suitable for Ammeter (Page no.19 Item no.5.27) 2023-24

ITEM21 - Supplying, fixing and wiring rotary selector switch suitable for Voltmeter (Page no.19 Item no.5.28) 2023-24

ITEM22 - Supplying,fixing and wiring3 Phase Digital Ammeter Voltmeter (Page no.19 Item no.5.29) 2023-24

ITEM23 - Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230 440VAC. 50 Hz 12/24V D.C.(Page no.19 Item no.5.38) 2023-24

ITEM24 - Supply, Erection, testing and commissioning of AMF panel suitable for kVA DG set. The panel is of cubical type base/floor mounting control panel with hinged doors, undrilled bottom gland plate, aluminium Bus Bar with the accommodation for A 4 pole contactor for alternator with thermal O/L relay,A 4 pole contactor for mains,HRC fuse for short circuit protection, Microprocessor based AMF module with supply failure timer, Restoration timer,3 impulse automatic engine start stop logic, Mains/generator voltage,capacity bypass switch and frequency sensing, PCC 1301controller with water temperature Lube oil pressure engine speed, Voltage ampere Frequency kVA, Running-hour count, No of starts, Fault indication, over under speed, Fails to start, Low oil pleasure, High engine temperature, Under/over voltage, over current, Earth fault relay, with indications for Mains on, Load on Mains, Battery charger on Push buttons AMF module by pass Mode, Battery charger unit with inbuilt Auto/Manual and Flat/Boost facility.The complete set shall have sufficient safety and adhere to NEC, NBC 2016, IEC,CPWD specifications, PCB norms and KSGEI Acts and Rules. KVA to 125 KVA