Rural Drinking Water And Sanitation Department Tender

code04 - Earth work excavation for pipelines/cables by Manual means upto 600 mm trench width, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, including dressing of excavated surfaces, disposing off or leveling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m. Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering and lift upto 1.5 m including cost of labour, tools, usage& other appurtenances required to complete the work. In all kinds of soils. Depth upto 1.50m CC road cutting with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code05 - Supplying, laying and jointing HDPE pipes of specified grade and conforming to IS 4984-2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and rolling and lowering into trenches, laying true to line and jointing of pipes and specials with electrofusion welding, giving hydraulic test as per relevant ISS with all lead and lifts including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excation, testing and commissioning. The rate is exclusive of required specials and fittings wherever necessary like saddle Tee, stub ends, flanged sets, bedns, reducers etc. complete (Contractor will make his own arrangements for procuring water for testing) etc. Note: Upto 110mm dia Coil shall be used. Rate revised as per Letter No:BWSSB/CE(V)/TA(V)/04/2022-23 Date:05.04.2022 63mm dia with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code06 - Supplying, laying and jointing HDPE pipes of specified grade and conforming to IS 4984-2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and rolling and lowering into trenches, laying true to line and jointing of pipes and specials with electrofusion welding, giving hydraulic test as per relevant ISS with all lead and lifts including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excation, testing and commissioning. The rate is exclusive of required specials and fittings wherever necessary like saddle Tee, stub ends, flanged sets, bedns, reducers etc. complete (Contractor will make his own arrangements for procuring water for testing) etc. Note: Upto 110mm dia Coil shall be used. Rate revised as per Letter No:BWSSB/CE(V)/TA(V)/04/2022-23 Date:05.04.2022 -do-PE100 (PN 6.0 / 6 Kg/cm2) 75mm with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code07 - Supplying of 63 MM Electro Fusion Coupler with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code08 - Supplying of 75 MM Electro Fusion Tee with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code09 - Supplying of -63MM Electro fusion Elbow with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code10 - Supplying of - 90 x 75mm dia dia Electro fusion Reducer with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code11 - Supplying and installation of Class SN8 Double Wall Corrugated HDPE pipe Specials outer wall corrugated and inner wall smooth piping system in accordance with IS 16098 part 2 and conveying to work site and lowering into trenches, laying true to line and level and perfect linking at joints with the help of two “O” rings and a coupler of suitable size, including loading and unloading at both destination including jointing with all labour, all lead and lift including encasing the special around to a depth of not less than 15 cm with screened soft soil available from the excavated soil. The testing commissioning including necessary hydraulic test to the required pressure as per ISS shall be done (the contractor shall have to make his own arrangement for procuring water for testing) - Electro fusion End Cap with Pipe of 0.2 m length with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code12 - Refilling available earth around trenches/pipelines, cables in layers not exceeding 20 cms in depth, compacting each deposited layer by ramming after watering with a lead upto 50 m , and lift upto 1.5 m. Including cost of all labour complete as per specifications with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code13 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 m3 capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, primer, sealant , curing of concrete slabs for 14- days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-in-charge of the work. ( Restoration For CC road cutting ) with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code14 - Supplying and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of ductile iron (DI) conforming to IS-1865 and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 only. The stem sealing should be with toroidal sealing rings (minimum 2 “ O “ rings). Body and bonut should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) For PN-10:For Suilce Valve of PN -10.0 and 50mm with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code15 - Supplying and fixing DI Resilient seated soft sealing SLUICE VALVE of variouis dia. with body bonnet of ductile iron (DI) conforming to IS-1865 and of grade GGG 40/50, shaft of stainless steel, wedge fully rubber lined with EDPM seals of NBR and the valves should be vacum tight and 100% leak proof with face to face dimensions as per IS 14846-2000 only. The stem sealing should be with toroidal sealing rings (minimum 2 “ O “ rings). Body and bonut should be coated with Electrostatically applied Epoxy Powder Coating with minimum coating thickness of 250 micron both inside and outside. The rate is inclusive of cost of valves, T.P set, galvanized bolts & nuts and rubber insertions etc. but excluding earth work. (Note: TP set should be considered only for DI pipes estimate. For MS pipes estimates, TP sets cost of corresponding dia shall be deducted from the SR rates of valves and provision for corresponding dia MS flanges should be made in the estimate.) For PN-10:For PN-10:For Suilce Valve of PN -10.0 and 80mm with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code16 - Supply and fixing of Single / Double chamber triple function tamper proof (Both the orifces to be housed in the single chamber) Air valves with Body and cover in Ductile cast iron of grade GGG 40/50. All internal parts such as float, shell with appurtenances., all cover bolts of austenitic alloy / SS 304 steel, DN 50 float of HOSTAFLON / SS 304 and gaskers and seals of EPDM. Epoxy powder coating (EP-P) inside and outside colour blue RAL5005. The valves should be designed for all the three functions i.e., 1. Large orifice for venting of large air volumes on start up. 2. Large orifice for intake of large air volumes. 3. Small orifice for discharge of pressurized air during operation. For PN 10.0 Air valve For TP Air Valves of 80mm dia. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code17 - Supplying S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level including loading and unloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey. RCC NP3 Class pipe of 250 mm dia. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code18 - Supply and fixing of fixed height surface box H-4057 MD-KU with PP 40% GF Lid, Housing of PA+, Locking clip of PP with Notched bolt M 12 x 130 hexagon head A2-70 for service connection valves, design derived from DIN 4057, should be supplied with Support tile I (FSL, FSS, SI). Should be able to receive class AA traffic loads. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code19 - Supplying and fixing Multijet class B inferential type, AMR compatible water meters with IP 68 protection totalizer confoming to IS 779 with its latest amendments of following size to service connections including conveying and fixing of necessary G.I. specials with appurtenances. complete, with all lead and lift. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code20 - Supply and fixing of HDPE water meter box with locking arrangement to protect the water meter of Class ‘B’ Multijet type of size 15 to 32 mm including HDPE box with base dia 300mm x lid dia 200mm x height 250mm with openable lid and the cover is buried below GL with lid flush with GL including earth work excavation for 600mm x 600mm and base sand filling for 100mm thick over which the cover is placed and enclosed by PCC 1:2:4 using 12-20mm BG jelly for an height of 150mm and refilling with excavated earth for balance 100mm height, disposal of excess earth with all lead and lifts with appurtenances complete as per drawing enclosed with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code21 - Supply of PPR Female Threaded Coupling confirming to IS 15801-2008 and DIN Standards with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code22 - Supply of PPR End Cap confirming to IS 15801-2008 and DIN Standards with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code23 - Supply of PPR Union confirming to IS 15801-2008 and DIN Standards with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code24 - Supply of PPR Gate Valve confirming to IS 15801-2008 and DIN Standards with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code25 - Providing and fixing brass bib cock of approved quality with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code26 - Providing and fixing flow control valve using food grade materials SS 316 ball/ 1/2" (15mm) including cost of all materials labour charges, HOM and testing by FCV nominal design is for 5 litre per min discharge at 0.5 bar pressure loss and should not exceed the flow rate of 7 litres per minute at 1 bar or more pressure. MOC of valve - food grade stainless steel SS 316, MOC of ball - stainless steel 316. Flow direction arrow embossed on its outside surface. the valve should act as flow control valve and non return valve. Minimum operating pressure : 0.10 Kgf (10cm head). Designed pressure : 1 m to 50m. Accuracy of valve: + 20% average flow rate. Orifice size : not less than 12mm. Ball size : not less than 12mm. Weight of FCV : not less than 125gms. Length : not be less than 70mm with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code27 - Earth work excavation by manual means for drains,canals, waste weir draft, approach channels, key trench, foundation of Bridges and such similar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work - In all kinds of soils Depth upto 1.5 mFor Stand Post For Platform with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code28 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)(2nd Quarter Revision of Rates for cement related items W.E.F. 07/07/2022) with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code29 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code30 - Providing Thermo-Mechanically Treated bars of grade Fe-500D or more Steel reinforcement for R.C.C. work including straightening, cut- ting, bending, placing in position, binding and anchoring to adjacent members whereever necessary complete as per Design including cost of material, labour, usage charges complete as per specifications. (The laps and wastages shall not be measured separately)(2nd Quarter Revision of Rates for steel related items W.E.F. 07/07/2022) with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code31 - Supplying HDPE pipes conforming to IS 4984:1995 with latest amendments and conveying to work site including loading and unloading at both destination and rolling, lowering into trenches, laying true to line and jointing of pipes and specials by electrofusion welding, as per standerd procedure and guide lines including encasing the pipe around to a depth not less than 15cms with cleaned soft gravel or selected earth available from the excavation etc., complete giving hydraulic test as per relevant IS Specification with all lead and lift including , testing and commissioning. The rate is exclusive of required specials and fittings etc., complete (Contractor will make his own arrangement for procuring water for testing)Upto 110mm dia,Coils shall be used. PE100 75mm(PN 10/10 Kg/cm2) Rate revised as per Letter 75mm PE100 PN-10 with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code32 - Approved Make Electro Fusion Saddle Comply with BS EN 12201- 3-2011 PN - 125 rating and food grade raw material per BS 6920 for water quality inteneded for human consumption. Material of construction PE 80 or PE 100 and color for fitting - Blue / black for water application EF tapping saddle is Vregulataed type designed to fuse at 40 volt AC EF tapping saddle have molded ss / bars metal female threaded outlet EF tapping saddle is fused by using a top loading pillar type presure exerting 1500N top load onEF saddle fusion time is is 170 secs and cooling time is 10m exerted pressure should be removed after completeing the 10mins cooling time 63x20mm, 75x20mm, 90x20mm, 110x20mm with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code33 - Providing and fixing 3 layer PP-R (Poly Propylene Random Copolymer) pipes confirming to IS.15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply, including all PP-R plain and brass threaded polypropylene random fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-In- Charge. PN 16 pipe,SDR 7.4-20mm Dia (Up to Water Meter) with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code34 - Supply and fixing of RCC demarcation stones of 30cms x 15cms and 90cms using 1:2:4 CC and 6mm dia rods for verticals and stirrups and rendered smooth, including engraving letters letters "KWB and ARROW" 6mm deep on the top including fixing demaracation stones 45cms below ground level and CC 1:3:6 , 15cms height with 8 cms offset around the stone and curing for 10days including erathwork in all types of soils with all lead and lift: ( STAND POST) with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code35 - Supplying at site pot rest slab of 0.45mx0.30mx0.20m in CC. 1:2:4 proportion with granite metal 20 mm and down size including plank centering and fom work, machine mixing, tamping including plastering 20 mm thick in C.M. 1:4 proportion with all lead as per specification with appurtenances., complete with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code36 - Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code37 - Printing new letter and figures of any shade with synthetic enamel paint black or any other approved colour to give an even shade with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code38 - Providing and fixing MS inspection door of size 60 cms x 60 cms, including MS frame made of 50x50x6mm angle, shutters made of 3mm thick MS sheets, with hinges, locking arrangements at top etc. including painting with anticorrosive approved paint etc. complete including all lead and lifts etc. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code39 - Supplying of 75 MM Electro Fusion Coupler with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code40 - Supplying of 75 MM Electro Fusion Elbow with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code41 - Supplying of -63MM Electro fusion tee with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code42 - Providing and fixing board displaying information, such as 'Name of work, Tender cost, Name of Contractor, Work completion and liability period etc', having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete, on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge & MoRTH specification 804 with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code43 - Supply and delivery of Woltman model with removal mechanism water meters conforming to ISO4064 part I,II,III class B or IS 779 and IS 2373 with lfie cycle test certificate from FCRI/NABL accredited lab. The water meters shall have magnetic drivers or mechanical drivers and shall be versatile for installationin any position.The meters shall be hydrodynamically,hydrostatically balanced. The runner, runner chamber,pointer of the meter shall be as per ISO 4064 class B specification. Dry dial excavated counter housing fully protected against flooding ensuring easy reading in all climates. Note: the above rates are basic rates basic rates inclusive o transportation charges, earthork ecavation, labour charges, cutting anfd threading, conveyance,welding and hire charges for tools and plants etc., complete. with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.

code44 - Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments -80mm dia with all lead and lifts, loading and unloading charges and all other incidental charges etc., for successful completion of work as per specifications and as per the directions of the Engineer incharge of the work.