Rural Development And Panchayat Raj Department Tender

004 - Providing Coursed rubble masonry (first sort) with hard stone in foundation and plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) (P.No. 9 I.No. 5.2 Building SR 2023-24 Volume -2 )

005 - Providing and laying flooring with burnt stone slabs 10 cms thick rough chistle dressed on cement mortar bed 1:6, 25 mm thick, and pointed with cement mortar 1:3, , including cost of materials, mortar, labour, curing complete as per specifications. ( PWD Common SR 2023-24, I.No. 9.27, Page No : 63, Volume-1)

006 - Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. (P.No. 7 I.No. 1.9 Common SR 2021-22 Volume -1 )

007 - Providing and laying in position Reinforced cement concrete for all Super structures of building Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/ trap basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators The cost includes all lead lifts, cost of all materials, quality confirming to the requirements of relevant IS codes labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications (The cost of steel reinforcement, dowel bars formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (P.No. 16 I.No. 2.5.1 Comman SR 2023 24 Volume 1 )

008 - Supplying, fitting and placing TMT FE 550/550D Steel Reinforcement complete as per drawing and technical specification. ( PWD Common SR 2023-24 Item No: 2.11, Page No : 90, Volume-1)

009 - Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.(P.No. 63 I.No.9.24 Building SR 2023-24 Volume -2 )

010 - Providing Mathi / Nandi wood wrought and putup for purlins, common rafters and similar work including cost of materials, labour, usage charges complete as per specifications.(SR 2023-24 Vol-2, P.No. 99, I.No. 12.3)

011 - Providing and fixing in position Mathi/Nandi wood fully panelled shutters for windows with stiles and rails of 35mm. thick, 75mm wide in two halves with panels of 25mm thick including cost of materials, labour charges, usage charges complete as per specifications. (excluding cost of fixtures)(SR 2023-24 Vol-2, P.No. 101, I.No. 12.24)

012 - Finishing walls with textured exterior paint of required shade :New work (Two coats applied @ 3.28 L/10 m²) over and including priming coat of exterior primer applied @ 2.20kg/10 m² to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. ( Vol-2 , PWD Common SR 2023-24 , Item No-8.29, Page No-45 )

013 - Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below:1. The surface to be polished is rubbed with sand paper 80 120 no. and then with sand paper of 160/180 no.2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs.3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs (P.No. 54, I.No. 8.82, RWS SR 2023-24 Volume -2)

014 - Providing and laying Cement concrete pavement with 1:2:4 for commercial & residential building floors, hardpaths, footpaths using 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size, including finishing complete as per Engineer in Charge. (P.No. 59, I.No. 9.4, RWS SR 2023-24 Volume -2)