Rural Development And Panchayat Raj Department Tender

PRED04 - Providing and fixing Steel work in built up tubular (round, square orrectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steelprimer, including welding and bolted with special shaped washers etc.complete. Hot finished welded type tubes including cost of materials,labour, usage charges of machinery complete as per specifications andas per directions of the Engineer-in-Charge.(PWDSR 2023-24 P.NO 82 I No.11.16.1 VOL 2 ).

PRED05 - Providing and fixing precoated galvanised iron profile sheets (size, shapeand pitch of corrugation as approved by Engineer-in-charge) 0.50 mm(+ 0.05 %) total coated thickness with zinc coating 120 grams per m2 asper IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on bothside of the sheet and polyester top coat 15-18 microns. Sheet shouldhave protective guard film of 25 microns minimum to avoid scratchesduring transportation and should be supplied in single length upto 12m or as desired by Engineer-in-charge. The sheet shall be fixed usingself drilling/self tapping screws of size (5.5x 55 mm) with EPDM seal,complete upto any pitch in horizontal/ vertical or curved surfaces,excluding the cost of purlins, rafters and trusses and including cuttingto size and shape wherever required.(PWDSR 2023-24 P.NO.26 I No.7.38 VOL 2 )

PRED06 - Providing and fixing precoated galvanised steel sheet roofingaccessories 0.50 mm (0.05 percentage) total coated thickness, Zinc coating120 grams per m2 as per IS: 277, in 240 mpa steel grade, 5-7 micronsepoxy primer on both side of the sheet and polyester top coat 15-18microns using self drilling/ self tapping screws complete Gutter (600 mm over all girth):Gutter (600 mm over all girth)

PRED07 - Providing and laying in position Reinforced cement concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications.M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates( PWDSR 2023-24 P.No.15 I No.2.2.1.1 Vol-1)

PRED08 - Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm (PWDSR 2023-24 P.NO 60 I No.9.12.2. VOL 2 )

PRED09 - Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ m2 including pointing the joints with white cement and matching pigments etc., complete.(PWDSR 2023-24 P.NO60 I No9.11. VOL 2 )

PRED10 - Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.(PWDSR 2023-24 P.NO 77 I No.11.5.1 VOL 2 )

PRED11 - Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding(PWDSR 2023-24 P.NO 86 I No.11.34 A VOL 2 ).

PRED12 - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) including cost of materials, labour, usage charges of machinery complete as per specifications.(PWDSR 2023-24 P.NO 87 I No.10.1.1 VOL 2 ).

PRED13 - Providing and laying in position Reinforced cement concrete M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork to be paid separately) M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates( PWDSR 2023-24 P.No.15 I No.2.2.1.1 Vol-1)

PRED14 - Steel Fabrication Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcementincluding cost of all materials, machinery, labour, cleaning, straightening,cutting, bending, hooking, laping/welding joints, tying with binding wire / softannealed steel wire and other ancilary operations complete as per drawing andtechnical specification( PWDSR 2023-24 P.No.18 I No.2.11Vol-1)

PRED15 - Providing 20 mm cement plaster of mix :1:6 (1 cement: 6 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge(PWDSR 2023-24 P.NO..41I No.8.3.2. VOL 2 )

PRED16 - Providing and fixing white vitreous china pedestal type water closet(European type W.C. pan) with seat and lid, 10 litre low level whiteP.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fix- tures complete, including cutting and making good the walls and floors wherever required :(PWDSR 2023-24 P.NO 131 I No.14.2VOL 2 )

PRED17 - White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps(PWDSR 2023-24 P.NO 132 I No.14.7.3VOL 2 )

PRED18 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal sibility for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes (PWDSR 2023-24 P.NO 122 I No.13 .33.3 VOL 2 )

PRED19 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal sibility for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal dia Pipes (PWDSR 2023-24 P.NO 122 I No.13 .33.4VOL 2 )

PRED20 - Earth work excavation by manual means for drains,canals, waste weir, draft, approach channels, key trenches, foundation of bridges and such simillar works in all kinds of soils , as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work.( PWDSR 2023-24 P.No.5 I No.1.4 Vol-1)

PRED21 - Supplying and errection of RCC rings for well steining of 0.30 Mtr Depth using M -20 grade cobcrete using clean graded granite or trap or jelly of approved quality 20 mm and down size well compacted including centring from work and plastering for both faces with C.M.1:3 proportion as per design using 6.5 mm M.S.Coil at the rate of 10 KGS /ring including cost of steel and fabrication oyt of water , errection etc,.1.80 mm dia (P.No.59I.No.11.20.1 RDWLSR for the year 2019-20)

PRED22 - Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. (The cost of steel reinforcement & formwork shall be paid separately)Mix 1:4:8( M5) Using 40 mm nominal size graded crushed coarseaggregatesMix 1:4:8( M5) Using 40 mm nominal size graded crushed coarseaggregates( PWDSR 2023-24 P.No.15 I No.2.1.2 Vol-1)

PRED23 - Supplying heavy gauge PVC conduit pipe ....... dia ....... mm thickconfirming to IS 2509 with suitable size bends, junction boxes,adhesive paste etc , and fixing using inverted wood plugs in case ofRCC ceiling and RCC wall/ stone structure or rawl plugs in case ofbrick walls and cement plastering the damaged portion using heavygauge saddles at an interval of 700mm using NF screws.(PWD SR 23-24 P.No,2 I.NO.1.1.3 )

PRED24 - Supplying heavy gauge PVC conduit pipe ....... dia ....... mmthick confirming to IS 2509 with suitable size bends, junctionboxes, adhesive paste etc , and fixing using inverted woodplugs in case of RCC ceiling and RCC wall/ stone structure orrawl plugs in case of brick walls and cement plastering thedamaged portion using heavy gauge saddles at an interval of700mm using NF screws.(ELEPWD SR 2023-24P.No,2 I.NO.1.2.3 )

PRED25 - Point wiring using copper wire with switch:Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using copper PVC Insulated multistrand 2x1.5 Sqmm copper wire with a 6 Amps flush type SP control switch shall be fixed on the plastic sheet gangbox,the other end of the wires shall be terminated with sufficient loose length in a wood /PVC round bolck complete for each out let a)Short up to 3 Mtrs from tapping point out let via switch b) Medium Point above 3 mtr upto from tapping point out let via switch c) Long point above 6 Mtr upto 10 Mtr from tapping point out let via switch.Short Point

PRED26 - Medium Point

PRED27 - Long Point

PRED28 - Supplying 6A flush type socket and 6 A flush type SP switch eithersurface/flush mounting in existing gang box or in 4mm thick plasticsheet and fixing over a flush mounted wooden box and wiring usingnecessary capacity wires as required as per IS 1293 and IS 3854 (PWD SR 2023-24 P.No,8 .NO.3.1)

PRED29 - Supplying and fixing of backlite DP switch with neon indicator over existing woodboard of flush mounting in a plastic plates ( PWD SR 2023-24 P.No,10 I.NO.3.14.12)

PRED30 - Supplying and fixing 32 Amps Security and Energy saving DP Switch with Key tag Suitable to oparative all 230 valts 50Hz AC Supply and Completely wired on exisiting box (PWD SR 2023-24P.No,9 I.NO.3.7)

PRED31 - Wiring for lighting/power circuit using one of FRLS PVC insulated1100V grade, multistrand copper wire with low conductor resistancesingle core in open or concealed system of wiring with specified IS694:20104.00Sqmm.1.5 Sqmm

PRED32 - 2.5 Sqmm

PRED33 - 4.00 Sqmm

PRED34 - Supplying and fixing of Electronic Ballast suitable for T5 Lampwith housing made of Pre-coated steel/PC, Operating voltage rangefrom 180V to 265V, 50Hz AC power Supply flicker free warm startwith over voltage protection, Inrush current protection, Deactivated lamp protection& End of Lamp life protection withPF 0.95 & TC(degC) 65 deg C compliance to EN 61347-2-3(Safety), EN60929(Performance), EN55015(EMI/RFI), EN61000-3-2(Harmonics), EN 61547 (Surge). Operating voltage range from180V to 265V, 50Hz AC power Supply.

PRED35 - Supplying of porcelain fuse channel with cutout on existing wooden /panel using necessary nuts,bults and washers etc., complete 32 amperes (PWDELESR 2023-24Page.No.14.Item No.5.7.2)

PRED36 - Supplying and fixing miniture circuit breakers on existing MCB distribution boards using fixing materials and 'C' type curve,indicator ON/OFF,energy cross-3 with Short circuit breaking capacity of 10 K and complete wiring as required.(PWD SR 2023-24 P.No,18 I.NO.5.17)

PRED37 - Supplying and fixing of modular switch & Connected accessories on existing modular switch plate as per IS 3854 and IS 1293 ( PWD SR 2023-24P.No,9 I.NO.3.6.2 )

PRED38 - Supplying of Ceiling Fan with Capacitor rating As per guideline ofBEE 5 star rating and IS:374/19 and also comply with IS: 1709/1984with latest amendment, Rated voltage 220 V/50 Hz, Rated power upto35 W +/- 10 %, Rated current As per IS:374/19, Rated power factor0.9 lagging(min), Rated speed 350 +/- 10% RPM, Rated air delivery210 +/- 10% Cubic Meter Minimum, Rated service value 6.2 CMM /W, Three Blades of blade leaf 1.05 mm thick Aluminium Alloy sheet,Class B motor insulation, Bearing Two ball bearings, Top 6202,Bottom 6201, as per IS specification, Motor winding. Temp rise Shall not exceed 75 deg C over and ambient of 40 0C by resistance methodat 245 V, Insulation resistance Shall not be less than Two Mega Ohms(2M Ohms), Leakage current Should not exceed 210 Micro Amp,Power input, W& current, Air Delivery & Fan Speed as perIS:374/2019 with latest amendment, 2year manufacturer Warranty. (BLDC fans)(PWD SR 2023-24 P.No,30 I.NO.6.4.1)

PRED39 - Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two coats) over and including water thinnable priming coat with cement primer after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(PWDSR 2023-24 P.NO.45 I No.8.25. VOL 2 )

PRED40 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.(PWDSR 2023-24 P.NO.48 I No.8.40 VOL 2 )