Rural Development And Panchayat Raj Department Tender

code04 - Grading-I (63 mm to 45 mm) Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.Grading-I (63 mm to 45 mm) etc complete as per direction of the Engineer incharge of the work.

code05 - Grading-II (53 mm to 22.4 mm); Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.etc complete as per direction of the Engineer incharge of the work.

code06 - Construction of sub-grade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table etc complete as per direction of the Engineer incharge of the work.

code07 - Providing and applying primer coat with SS1 grade Bitumen Emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/m2 using mechanical means.etc complete as per direction of the Engineer incharge of the work.

code08 - Providing and applying tack coat with VG-10 Bitumen using pressure distributor at the rate of 0.25 kg/m2 on the prepared bituminous surface cleaned with mechanical broom etc complete as per direction of the Engineer incharge of the work.

code09 - Providing laying and rolling of open - graded premix surfacing of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using viscosity grade bitumen VG-30 to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable Hot mix plant of capacity not less than 40/60 TPH laying and rolling with a smooth wheeled roller, finished to required level and grades. etc complete as per direction of the Engineer incharge of the work.

code10 - Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A and B seal coats with bituminous binder VG-30. Type B Premix Sand Seal coat etc complete as per direction of the Engineer incharge of the work.

code11 - Kilometre Stone Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in positionincluding painting and printing Ordinary Kilometer Stone ( Pre Cost) etc complete as per direction of the Engineer incharge of the work.

code12 - 200 m stone (precast) etc complete as per direction of the Engineer incharge of the work.

code13 - Retro-Reflectorised Traffic Signs Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC:67:2012 made of Class B Type IV retro reflective sheeting fixed over 2 mm thick aluminium sheeting vide clause 803.1, 3mm/4mm thick Aluminium composite material sheet depending on the size of the sign fixed over the back support frame of min 25 x 25 x 3mm angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing.The sign shall be maintained as per Item 12 & IRC: 67:2012 60 cm equilateral triangle etc complete as per direction of the Engineer incharge of the work.

code14 - Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 g/m2 area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35:2015.The finished surface to be level, uniform and free from streaks and holes MoRTH specification 803 etc complete as per direction of the Engineer incharge of the work.

code15 - Supplying and Fixing of Molded Shank Raised Pavement Markers Cats Eye made of polycarbonate and ABS moulded body and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face and shall support a load of 16000 kg tested in accordance to ASTM D 4280 Type H and complying to Specifications of Category A of MORTH Circular No RW NH 33023/10-97 DO III Dt 11.06. 1997. The height, width and length shall not exceed 50 mm 100 mm and 1022 mm and with minimum reflective area of 13 cm2 on each side and the slope to the base shall be 35/5 degree.The strength of detachment of the integrated cylindrical shanks of diameter not less than 19/2 mm and height not less than 30/2 mmfrom the body is to be a minimum value of 500 Kg. Fixing will be by drilling holes on the road for the shanks to go inside without nails and using epoxy resin based adhesive as per manufacturers recommendation and complete as directed by the engineer.The contractor shall submit a two year warranty for satisfactory field performance including stipulated retro-reflectance of the reflecting panel to the Engineer MoRTH specification 806 etc complete as per direction of the Engineer incharge of the work.

code16 - Providing and fixing board displaying information such as Name of work Tender cost Name of Contractor Work completion and liability period etc having rectangular shape of 1.20m x 0.90m size made out 18 gauge (1.25mm) thick mild steel sheet painted with one coat of Zinc chromate stoving primer and two coats of enamel paint on front side and grey stove enamel on back side and border / messages / symbols etc. with approved colour shade paint complete on M.S.angle of size 35 x 35 x 3 mm frame with properly cross braced M.S. angles of size 35mmx35mmx3mm duly painted including Two M.S. angle iron posts of size 65 mm x 65 mm x 6 mm, 3.65 m long painted with alternate black and white bands of 25 cm width including all fixtures etc.and fixing the boards in 1:4:8 concrete block of size 60 cm x 60 cm x 75 cm including, excavation, refilling, transportation, and labour etc complete. Spec. No. As directed by Engineer in Charge & MoRTH specification 804 etc complete as per direction of the Engineer incharge of the work.