Rural Development And Panchayat Raj Department Tender

KSRB 15.12.1Providing Gopi colour washing to new wall surface in two coats with lime and gopi colour of approved quality, to give an even shade after throughly brooming the surface to remove all dirt, dust, mortar drops and other foreign matter including cost of materials, labour, complete as per specifications (P.No.118 I.No.15.44 )

Providing and applying enamel painting two coats (excluding primary coat) over new steel or other metal surface brushing to give an even shade after cleaning oil, grease, dirt and other forign matter, including cost of all materials, labour, complete as per specification.

Providing wood frames of doors,windows, clerestory windows, ventilators and other frames,wrought, framed or assembled including making plaster groves(excluding cost of cement concrete and side clamps),but including cost of materials, labour,HOM complete as per specifications.(I.No.9.11, Page.No.53)Honne wood frames

Providing and fixing in position fully panelled wood shutters for doors,with styles and rails of 40mm thick with bottom and lock rails 180mm wide top rail and styles 100mm wide as per drawing and panels of 25mm thick including cost of materials,labour, HOM complete as per specifications No.KBS 9.34.(I.No.9.15, Page.No.53)Honne wood frames

Repairing and fixing (panelled or glazed) to doors,windows,ventilators and cupboards, including cost of all materials, labour,HOM complete as per specification.

"Providing and fixing cold rolled prepainted steel windows of IS standards, made out of 0.6mm thick deep drawing quality galvanised on both sides 120gms/sq.mtr. Primer coat upto 5 microns with thermosetting epoxy resin and finish painted with a polyester based paint 20 microns thick. The size of profiles is approximately 46 x 52mm for external frames, 46x46mm section for shutters, 46x70mm section for centre mullion/transom and 18x31mm section is for fixing glasses. The section should be cut to length joint mitred and assembling by means of corner brackets made out of cold rolled cold annealed strips of 1.2mm thick duly galvanised and fixed with nickle plated self taping screws.The shutters are provided with approved quality of fixtures like handles made out of zamac alloy die cast and powder coated, receiver made out of glass filled nylone and hinges made out of CRCA powder coated. 4mm thick glass should be fixed with EPDM gaskets. Guard bars fabricated out of 10mm square bright bars shall be fixed horizontally at 125mm C/C by rivetting to the external frame. The above frames are fixed to the concrete / masonry walls by means of self expanding screws.d)� with 4mm tinted glass with gaurd bars

KSRB 7.9: Providing and fixing M.S. grill work for windows and ventilators weighting 21 kg/sqm using M.S. flats, or M .S. square rods or combination of M.S. flats and square rods as per approved design, drawing including cutting steel sections and welding the same to required pattern with a coat of red lead primer, cost of materials, fixtures, labour and HOM of machinery complete as per specifications. Specification No. KBS 7.12

KSRB 2-1.1: Earthwork in surface excavation in ordinary soil for levelling and lowerin g the ground manually (other than foundation of buildings, culverts, road drains and trenches of pipe lines and cables) and removing the excavated stuff to a distane not exceeding 50m and lift upto 1.5m excavated surface levelled and neatly ressed, disposed earth to be levelled after breaking specification No. KBS 2.1(a) 2.3.1 (P.No.6 I.No.2.2) Hard soil.

KSRB 4-1.3 Providing and laying In position plain cement concrete of mix M7.5 with OPC cement @180kgs wih 40mm down size graded granite metal coarse aggregates @0.85cum and fine aggregates @0.57cum, machine mixed, concrete laid in layers not exceeding 15 cms thick, well compacted, min foundation and plinth, including cost of all materials, labours, HOM of machinery, curing complete as per specifications, (P.No. 13, I.No. 4.3)

KSRB 4.1.7Providing and laying position plain cement concrete of mix M 10 with OPC cement @220kgs wih 20mm down size graded granite metal coarse aggregates @0.84cum and fine aggregates @0.56cum, mmachine mixed, concrete laid in layers not exceeding 15cms thick, Well compacted in foundation and plinth etc., including cost of all materials, labour, HOM of machinery, curing, complete as per specification. (P.No. 13 I.No. 4.7)

KSRB 4.2.2 : Providing and laying in position reinforced cement concrete of design mix M20 with OPC cement @ 320kgs with 20mm and down size graded granite metal coarse aggregates @ 0.878cum and fine aggregates @ 0.459cum, with superplastisiser @ 3lts confirming to IS9103-1999 Reaffirmed-2008, machine mixed, concrete laid in layers not exceeding 15 cms thick, vibrated for all works in foundation plinth and ground floor level for roof slabs,staircase,lintles,retaining walls, return walls, walls (any thickness) including attached plasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window cills, fillets etc.including cost of all materials, labour, HOM of machinery, curing, complete as per specifications. 4,1,4,6 (P.No.14, I.No.4.13)

KSRB 6.1-3 Providing and constructing burnt brick masonary for basement and superstructure with approved quality of non modular bricks of standard size of class designation 3.5Newton per sqmm with cement mortar 1:6 including cost of materials, labour, curing complete as per specifications.(P.No. 29, I.No. 6.3)

KSRB 4.9.2 Providing TMT steel reinfocement for R.C.C work including straightening, cutting, bending, hooking, placing in position, lapping and / or welding wherever regured, tying with binding wire and anchoring to the adjoining members wehever necessary complete as per design (laps, hook and wastage shall not be measured and paid) cost of materials, labour, HOM mspecification. (P.No. 18, I.No. 4.46.2)

KSRB 4-6-2 Providing and removing centring, shuttering, strutting, popping etc, and removal of form work for flat surface such as suspended foors,roofs, landings, balconies and likes, thickness up to 200mm including cost of materials, labour, curing complete as per specifications.(P.No. 16,I.No. 4.29.2)

KSRB 4-6-2 Providing and removing centring, shuttering, strutting, popping etc for edges of slabs and breaks in floor including cost of all materials, labour, curing complete as per specifications.(P.No. 17 I.No. 4.36)

KSRB15-3.2 Providing 12mm thick cement plaster in single coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. (P.No. 115, I.No. 15.10)

KSRB15-3.8 Providing 18mm thick cement plaster in single coat with cement mortar 1:4, to brick masonry including rounding off corners wherever required smooth rendering, Providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications. (P.No. 116 I.No. 15.16)

KSRB 15-4.4 : Extra for Providing and mixing waterproofing compound in cement plaster work at one kg per bag or in the proportion recommended by the manufactures, for cement mortar 1:4, 18mm thick cost of materials complete as per specifications. (P.No. 116 I.No. 15.26)

Earthwork excavation for pipeline trenches including depositing on bank upto a lead of 50 mtrs and depth up to 2.00 mtrs. Including shoring and strutting, danger lighting and using sight rails and boning rods at every 100 mtrs. Wherever necessary as directed in the following strata. (Manual Means) in hard soil. (Rdws DSR P.7.00 I.No.2.22.1)

Providing and fixing Chorinted Poly Venyl Chloride (CPVC) pipes conforming to IS 15778 having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings, this includes jointing of pipes and fittings with one step solvent cement, trenching, refilling & testing of joints complete. (External work) -25mm nominal OD pipes. (PWD 2018-19 Page no 99 I no.13.87.3)

Supplying HDPE pipes conforming to IS 4984:1995 with latest amendments and conveying to work site including loading and unloading at both destination and rolling, lowering into trenches, laying true to line and jointing of pipes and specials by electrofusion welding, as per standerd procedure and guide lines including encasing the pipe around to a depth not less than 15cms with cleaned soft gravel or selected earth available from the excavation etc., complete giving hydraulic test as per relevant IS Specification with all lead and lift including , testing and commissioning. The rate is exclusive of required specials and fittings etc., complete (Contractor will make his own arrangement for procuring water for testing)Upto 110mm dia,Coils shall be used. (RWS page no 95 I no10.20.1) 63mm dia of 6ksc

Supplying HDPE pipes conforming to IS 4984:1995 with latest amendments and conveying to work site including loading and unloading at both destination and rolling, lowering into trenches, laying true to line and jointing of pipes and specials by electrofusion welding, as per standerd procedure and guide lines including encasing the pipe around to a depth not less than 15cms with cleaned soft gravel or selected earth available from the excavation etc., complete giving hydraulic test as per relevant IS Specification with all lead and lift including , testing and commissioning. The rate is exclusive of required specials and fittings etc., complete (Contractor will make his own arrangement for procuring water for testing)Upto 110mm dia,Coils shall be used. (RWS page no 95 I no10.20.1) 90mm dia of 6ksc

KSRB 13.6.1Providing and fixing in position brass bib cock of approved quality 25 mm nominal bore including cost of all materials, labour and HOM of equipments with all leads complete as per specifications. with all lead & lift loading and unloading cost & conveyance of materials labour charges etc complete and as directed by the Engineer -in-charge ( PWD SR P No-93 I N0- 13.25 )

Refilling the basement and pipeline trenches with selected available earth from trench excavation including watering, Consolidation in layers of 15 cm thick including disposing of the surplus earth with all lead & lifts. (Compacting with vibro roller) . (DSR rdws P.8 I.No.2.25)

Supplying and drawing 3 core flat PVC sheathed submersible pump cable manufactured with electrolytic grade copper with flexible copper with low resistance conductor confirming to IS:8130-1984 and virgin grade PVC insulation and powder coating extruded PVC sheathed suitable for working voltage upto 1100Volts as per IS-694:1990. (Gulburga PWD Electrical DSR P.no.7,I.No.2.6.1)

Supply of Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well and confirming to IS 8034 1.0 HP 7stage, h+30.00mtrs,Discharge 30LPM. (Rdws P 85.00,I.No.12.01.3a)

Providing and fixing 60x60cms M.S. inspection door with necessary M.S. frame made out of M.S. angle 50x50x6mm and M.S. shutters of 31.5mm or B.G.10 thick with hinges on top and locking arrangement, painting etc., complete (for RCC over head tank and G.L.S.R. (Rdws P 29.00,I.No.4.66)

KSRB 13-11.1 Supply and errection and placing on terrace polyethylene water storage tank of 1000litre capacity (P.No. 96 I.No. 13.78 of PWD)

Erection of outdoor type panel board and meter board units with all necessary materials and labour including providing cement concrete foundation bed etc., complete. (Rdws P 90.00,I.No.12.18)

Supplying heavy gauge PVC Conduit Pipe ….dia .......mm thick with suitable size bends, metal junction boxes adhesive paste etc., by groove cutting in the wall and fixing by bracing U or J hooks and cement plastering up to the wall surface and run with 18 SWG GI fish wire run throughout the conduit wherever necessary. - 25mm dia 2mm thick 25mm dia 2mm thick

Supplying and fixing sheet metal box made out of 18 SWG sheet metal with necessary holes for cable/conduit entry as required with one coat of primer of approved make etc. - 180x90x65mm

Supplying and flush mounting teak wooden box without front plank, made of not less than 12mm thick wood, after due groove cutting, Finishing with necessary cement plastering complete. (300x300x76mm)

Supplying and flush mounting teak wooden box without front plank, made of not less than 12mm thick wood, after due groove cutting, Finishing with necessary cement plastering complete. (254x178x76mm)

Supplying and fixing PBBC/Bakelite straight or slant batten holder and wiring with 60w/230 volts lamps.

Supplying patty type flurecent tubelight fitting of 4 feet 28 wats flureent tube of 230 volts made of M.S sheet and stve enamelled with heavy duty fill alumium choke starter, locking type brass conact holders mouned on foldable type sheet base fully wired.

Supplying capacitor type ceiling fan complete with down road blades shakle regulator capacities., for operation on 230 volts 50 cyeles single phase AC supply conforming to ISI 374-1979 and with double ball bearing sytem and as per technical approved (1200 mm swing)Regural Model

Point wiring using Copper wire with switch. Supplying and wiring adopting loop system in existing PVC Conduit / casing capping using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated, 2 X1.5Sq.mm Cable confirming to the GTP, with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. GROUP A - Short point upto 3Mtr from tapping point to out let via switch

Point wiring using Copper wire with switch. Supplying and wiring adopting loop system in existing PVC Conduit / casing capping using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated, 2 X1.5Sq.mm Cable confirming to the GTP, with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. GROUP A - Medium point above 3Mtr upto 6Mtr from tapping point to out let via switch

Point wiring using Copper wire with switch. Supplying and wiring adopting loop system in existing PVC Conduit / casing capping using 1100V grade, COPPER conductor flexible multistrand FRLS PVC insulated, 2 X1.5Sq.mm Cable confirming to the GTP, with a 6Amps flush type SP control switch shall be fixed on the existing plastic sheet / gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. GROUP A - Long point above 6Mtr upto 10Mtr from tapping point to out let via switch

Supplying 6A flush type socket and 6 amps flush type SP switch either surface/flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3654 - 6Amps 3/5 Way

Supplying 4mm thick plastic sheet with necessary nitches for fixing switches, regulators etc., and fixing on existing wooden or metal box using N.F. screws.

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898. - 6-32 Amps DP

Supply of LED floodlight luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate/clear glass material, delivering superior light output. Rated life Burning Hrs 50000 hr @ Lumen Maintenance of 70%, CCT > 5500K, IP 66 optical and electrical compartment & impact resistance of complete luminaire > IK08. Power Factor >0.9 with mains, Surge Protection- Min 5KV along with Over voltage/ Overload, short circuit/ miss-wiring protection. Compatible for pole mouting with outer dia of 40mm to 50mm. Universal Voltage driver to operate wide voltage range from 100V to 270V 50/60Hz application. Compliance to IS 10322/ IEC 60598, LM 79 & LM 80 Adherence with RoHS. UL approved MCPCB. Top access street light with single screw to ensure ease of maintenance at the sight site location with minimized minimal tools. LED Light fixture with ........W System Power consumption. LED Efficiency>130lm/w, nominal CRI >75. Luminaire manufacturer should have inhouse facility accredited by NABL/CPRI & any Government certified agency & Design & Development facility certified by ISO 9001:2008 . Housing with supplier word mark /name shall be Engraved / Embossing on the die cast housing/ Body part. Warranty of 2 Years against any manufacturing defect working under standard electrical conditions as mentioned above should be given by LED manufacturer & Cree/Nichia/ Lumileds/Osram make LED Source. PWD ELE SR P No.67, I.No 12.9.7,12.9.2, LED Floodlight 150W

Wiring for lighting/power circuit using one of FRL SPVC insulated 1100Vgrade, multistrand Copper with low conductor resistance single core wire in open or concealed system of wiring with specified IS-694:1990 & confirming to GTP of GROUP -A. 4 sq.mm

Supplying and fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicat or ON/OFF,energy cross-3with Short circuit breaking capacityo f 10K and complete wiring as required. 40Amps TPN

Providing Name board for the work