Rural Development And Panchayat Raj Department Tender

code04 - Construction of sub-grade and earthen shoulders with approved material obtained from borrow its with all lifts & leads, transporting to site, spreading, grading to quired slope and compacted to meet requirement of table No. 300-2

code05 - Construction of Granular Sub-Base of required grading as per design mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the esired density, complete as per clause 401

code06 - Laying Cement Concrete Pipe NP3 (burried conduits) on first class bedding of granular material including fixing collar with cement sand mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonary work in head wall and parapets

code07 - Providing and constructing un-reinforced plain cementconcrete pavement, thickness as per design, over aprepared sub base, with 43 grade cement or any othertype as per Clause 1501.2.2 M20 (Grade), coarse andfine aggregates conforming to IS:383, maximum sizeof coarse aggregate not exceeding 25 mm, mixed ina concrete mixer of not less than 0.2 m3 capacity andappropriate weigh batcher using approved mix design,laid in approved fixed side formwork (steel channel,laying and fixing of 125 micron thick polythene film,wedges, steelplates including levelling the formwork asper drawing), spreading the concrete with shovels, rakes,compacted using needle, screed and plate vibrators andfinished in continuousoperation including constructionjoints, primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawingand technical specificationclause 1501 with all lead, lifts,loading & unloading charges, cost and conveyance of allmaterials, labour, equipments etc., complete. as per thedirections of the Engineer-in-charge of the work.

code08 - Providing and applying primer coat with SS1 grade Bitumen Emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg/m2 using mechanical means.

code09 - Providing and applying tack coat with RS1 Bituminous Emulsion using emulsion pressure distributor at the rate of 0.20 kg/m2 on the prepared bituminous surface cleaned with mechanical broom

code10 - Mix Seal Surfacing Providing, laying and rolling of Close-Graded Premix Carpet (OGPC) surfacing material by Manual Means of 20 mm thickness composed 13.2 mm to 0.9 mm (Type-B) aggregates using VG30 bitumen to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10 kN static roller and finishing to required level and grades as per Technical Specification

code11 - Providing and fixing of typical Logo board as per specifications and drawing. Two ACP Sheet of 3mm thick, top and Bottom plate duly welded/bolted with MS Square angle 25mm x25mmx 5mm size on back and on the edges. The Top and Bottom plate will be welded/ bolted to 1 nos75x75x6 mm square Hallow section duly embedded in cement concrete M15 Grade of 600*600*600 mm, 450 mm below ground level.Retro-Reflecting Sheet as per IRC:67 Clause 1701.3.8.1 fixed over aluminium sheeting.All sections of steel tube will be painted with primer and two coats of epoxy paint as per drawing.

code12 - Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 g/m2 area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35:2015.The finished surface to be level, uniform and free from streaks and holes.