Rural Development And Panchayat Raj Department Tender

code04 - Providing and constructing un-reinforced plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M20 (Grade), coarse and fine aggregates conforming to IS:383:2016, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including construction joints, , primer, sealant , curing of concrete slabs for 14-days, and water finishing to lines and grade as per drawing and technical specification clause 1501 with all lead, lifts, loading & unloading charges, cost and conveyance of all materials, labour, equipments etc., complete. as per the directions of the Engineer-incharge of the work ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code05 - Earth work excavation for Foundation by manual means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code06 - Providing and laying in position Cement Concretefor levelling course for all works in foundation. The granitetrapbasalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 1:4:8 Using 40 mm and down size graded crushed coarse aggregates ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code07 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works other parallel works from 0.50m to 3.50 m height. The granitetrapbasalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates FOR DRAINS ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code08 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granitetrapbasalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates FOR DECK SLAB ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code09 - Providing and laying in position Cement Concrete for all Sub structures of building, Irrigation works, Sub structure works of bridges, Drain works & other parallel works from 0.50m to 3.50 m height. The granitetrapbasalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates FOR RETAINING WALL ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code10 - Supplying, fitting and placing TMT FE 550 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, lapingwelding joints, tying with binding wire soft annealed steel wire and other ancilary operations complete as per drawing and technical specification ALL OTHER TYPES OF STRUCTURE ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code11 - Water purification plants Providing, Installation and Commissioning of automatic Water purification plant (RO+UF) with all accessories piping, product water tank on single phase power supply as per the enclosed detailed Technical Specifications including cost of material, loading and unloading and as directed by the Engineer in charge. (Ref- detailed specification enclosed seperatly). Note- 1.The above rates mentioned are only for the preparation of estimate purpose. 2. All items are to be of BSI NFS standards,with BSI NFS mark . 3. Tenders to be invited for procurement. 4. No direct payment should be made under any situation or condition or on any account. 5. After commissioning of plant necessary testing to be done for the satisfactory of Engineer Incharge. Note Refer the ANNEXURE F for Detailed Specification of Each components For 1000 LPH Skid Type ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code12 - Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall 25 mm nominal dia Pipes ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code13 - Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 16 (1 cement 6 coarse sand) ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code14 - Providing and fixing Steel work in built up tubular round, square or rectangular hollow tubes etc. trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code15 - Filling available earth (excluding rock) in trenches,plinth, sides of foundations and other similar works etc.in layers not exceeding 20cm in depth, consolidatingeach deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code16 - Providing and laying in position Cement Concrete for levelling course for all works in foundation. The graniteortraporbasalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 136 Using 20 mm and down size graded crushed coarse aggregates ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code17 - Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two coats on new work after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code18 - Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections appropriate sections and other sections of approved make conforming to IS 733 and IS1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing paneling, C.P. brass stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) For Fixed Portion Anodised aluminium (anodised transparent or dyed to required shade according to IS 1868, Minimum anodic coating of grade AC 15) including cost of materials, labour, usage charges of machinery complete as per specifications ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code19 - Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item)With float glass panes of 5 mm thickness (weight not less than 12.50 kgsqm) including cost of materials, labour, usage charges of machinery complete as per specifications ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code20 - Providing & fixing corrugated G.S. sheet roofing including vertical curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete as per design drawings (up to any pitch in horizontal vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as per the direction of Engineer in charge.0.63 mm thick with zinc coating not less than 275 g per sqm ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code21 - Providing and laying vitrified floor tiles with thickness 9-10 mm in different sizes with water absorption less than 0.08 percentage and conforming to IS 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 14 (1 cement 4 coarse sand), jointing with grey cement slurry at 3.3 kg m2 including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code22 - Lettering with black Japan paint of approved brand and manufacture to give an even shade including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code23 - Earth work excavation for Foundation by manual means for all works depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK

code24 - Providing and laying in position Cement Concretefor levelling course for all works in foundation. The granitetrapbasalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications.Mix 1:4:8 Using 40 mm and down size graded crushed coarse aggregates ---- THE RATES INCLUDES ALL LEADS, LIFTS, LOADING, UNLOADING, COST AND CONVEYANCE OF ALL MATERIALS, LABOUR, EQUIPMENTS ETC COMPLETE AS PER THE DIRECTION OF THE ENGINEER IN CHARGE OF WORK