Rural Development And Panchayat Raj Department Tender

code04 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code05 - Providing Brick work with common burnt clay modular bricks of class designation 3.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work.complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code06 - Providing 12 mm cement plaster finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code07 - Providing 15 mm cement plaster with cement mortar 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code08 - Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two coats) over and including water thinnable priming coat with cement primer after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code09 - Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge.

code10 - Finishing walls with water proofing cement paint of required shade :New work (Two coats applied @ 4.84 kg/10 m²) to give an even shade after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labourcomplete as per specifications and as per directions of Engineer-in-charge. complete with all lead and lifts etc., complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code11 - Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats,square or round bars etc. including priming coat with approved steel primer all complete. Fixed toopenings /wooden frames with rawl plugs screws etc complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code12 - Providing & fixing of 2-track x 2-panel sliding windows made out of multi chambered UPVC (Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead free, gaskets -grey colour having isolated drainage and reinforced with Galvanized Iron profile through-out the window frame. The outer frame having an overall size of 50mm width x 42mmheight with reinforcement of 1mm thickness and Sash with overall size of 31mm X 57mm with Gi reinforcement of 1mm for the frame and 1.5 mm for the sash. Coextruded Glazing bead for fixing of glass shall be of size 21.5mm x 9.5 mm. Windows shall be provided with 5mm plain float glass, standard hardware& single point locking system with touch lock. Wall thickness of frame & sash shall be of 1.8+-0.2 mm. Maximum possible size 1519mm x 1519mm. (The cost is inclusive of all fixtures and separate charges for minor T&P's shall not be made) complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code13 - Providing and laying Polished Glazed Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). Size of Tile 600x600 mm m2 complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code14 - Providing & fixing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 m diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete as per design drawings (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required as per the direction of Engineer in charge. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code15 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge.

code16 - Providing and fixing 304 - grade stainless steel hand rails of 14-gauge pipes for Ramps or Staircase are made out of stainless steel hallow pipes, using 50mm dia for verticals @1.60 mtr c/c are fixed to the ramps or steps by drilling with bolts and 100mm dia MS base plates 10mm gauge for fixing of Vertical pipes 4 - Nos anchor bolts & 40mm dia pipes are fixed horizontally for 2-rows top, one pipes are fixed with vertical pipes another one are fixed with elbows and 25mm dia pipes are fixed horizontally for 2-rows below top measure @ equal intervals including cutting, welding, bending wherever necessary with suitable caps @ tops, bottoms & corners finishing with mat / shining etc., complete including cost and conveyance of all materials, labour for all items of work, HOM of equipment with all lead and lift, loading and unloading, transportation charges and all other incidental charges etc., complete as per specification and directions of the Engineer-in-charge of the work. Ramps or Staircase for physically challenged. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code17 - Supplying 6A flush type socket and 6A flush type SP switch either surface /flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3854 complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code18 - Supplying and fixing superior quality modular switch mounting poly car bonat eplate withne cessary supporting back plate with requir ed nos.of machine screws, bolts nuts etc., complete on the existing metal /PVC box. complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code19 - Supplying and flush mounting teak wooden box without front plank, madeo fnot lessthan 12mm thick wood, after due groove cutting, finishing with necessary cement plastering complete.complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code20 - Wiring for lighting/ power circuit using one of FRLSPVC insulated 1100V grade, multistr and copper wire with low conductorr esistance single coreinopen or conce aled system of wiring with specified IS-694:2010 1.5 mm2 complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code21 - Wiring for lighting/ power circuit using one of FRLSPVC insulated 1100V grade, multistr and copper wire with low conductorr esistance single coreinopen or conce aled system of wiring with specified IS-694:2010 2.5 mm2 complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code22 - Wiring for lighting/ power circuit using one of FRLSPVC insulated 1100V grade, multistr and copper wire with low conductorr esistance single coreinopen or conce aled system of wiring with specified IS-694:2010 1 mm2 complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code23 - Supplying and fixing of PVC casing and capping on the wall or ceiling using necessary material slike bends, junction box, elbows, screwsatan interval of 300 mm as required. complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code24 - Supplying and drawing Flexible Multi core Cable manufactured withel ect rolytic grade flexible copper with low conduct or confirming toIS8130-1984and (Virgin) PVC insulations heath edsuitable forworking voltage upto 1100 Volts as per IS-694:1990 complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code25 - Supplying & fixing miniature circuit breaker son existing MCB distribution board susing necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10 Kand complete wiring as required confirming to IEC 60898. complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code26 - Fixing all type sand all capacities offl uorescent/ fals eceiling/ spotlight/ CFL/ LED fitting sindoor on the wall/ ceiling/ rafters/ girders using 23/0.0076" twintwisted PVC insulated wires, required No so fround blocks and clamps. complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code27 - Supplying and wiring adopting loop systemin existing PVC Conduit /casing capping using 2x1.5Sqmm (Phase&Neutral) &1x1.0sqmm (Earthwire) FRLS multistr and PVC insulated copper wire (confirmingtoIS-694:andlatestamendments) with a 6Amps flush type SP control switch shall befixed onthe existing plasticsheet /gangbox, theother end ofthe wires shall beterminated with sufficien tloose leng thina wood/ PVC round block.completeforeach outlet. complete with all leads and lifts. with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.

code28 - Lettering with black Japan paint of approved brand and manufacture to give an even shade including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. complete with all lead and lifts etc., complete as per direction of the Engineer-in-charge of the work.