Rural Development And Panchayat Raj Department Tender

code04 - Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening,cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete --- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code05 - Providing Mathi/Nandi wood frames of doors, windows, clerestory windows, ventilators and other frames, wrought, framed or assembled including making plaster groves (excluding cost of cement concrete and side clamps ), but including cost of materials, labour, usage charges --- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code06 - Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding--- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code07 - Providing and fixing in position Honnewood fully panelled shutters for windows with stiles and rails of 35mm. thick, 75mm wide in two halves with panels of 25mm thick including cost of materials, labour charges, usage charges complete as per specifications. (excluding cost of fixtures)- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code08 - Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :New work (two coats) over and including water thinnable priming coat with cement primer after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete - Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code09 - Finishing walls with water proofing cement paint of required shade :Old work (one coats applied @ 2.20 kg/10 m²) over priming coat of primer applied @ 0.80 l/10 m² complete including cost of Priming coat including preparing the surface after thoroughly cleaning the surface to remove all dirt, dust and foreign matter, cost of materials, labour complete - Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code10 - Dismantling tile work in floors and roofs laid in cement mortar including stacking material to the appropriate disposal area as per direction of Engineer-in-charge. For thickness of tiles 10 mm to 25 mm- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code11 - Supplying and filling in plinth with sand under floors, foundation of Bridges including watering, ramming, consolidating and dressing complete.- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code12 - Flooring with 25mm thick polished tandur blue stone slabs using cement mortar 1:6, 25mm thick over existing cement concrete bed or top of roof laid to line and level and jointed with cement slurry mixed with pigment to match the shade of the slab, , including cost of materials, labour, curing, polishing complete - Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code13 - Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in superstructure above plinth level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code14 - Providing 15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix: 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete - Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code15 - Providing and laying water proofing treatment to the Roof with PU based single component elastomeric pure polyurethane based coating on New terrace/Chajjas/Sunken portion of WC:Bathroom, cold applied PU waterproofing membrane that is highly elastic with elongation greater than 400% and tensile strength greater than 2MPa as per ASTM D412. The waterproofing membrane to be applied in 2coats @ 1.6 kg/m2 to achieve final DFT (Dry Film Thickness) of 1mm including prime coat of epoxy primer @150 g/m2 and protection with 120gsm Geo-textile over the waterproofing membrane. The finished cost to include surface preparation, making coving at Junction, Bore Packing, treatment of construction joints completely - Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code16 - Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer- in-charge: Pre-laminated particle board with decorative lamination on both sides including cost of materials, labour, usage charges of machinery complete- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code17 - Providing and Fixing of G.I. pipes 40 mm dia- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code18 - Providing and fixing Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished seamless type tubes including cost of materials, labour, usage charges of machinery complete - Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code19 - Providing & Fixing of Mineral Fibre Suspended Ceiling System in the module size of 600x600x19mm with Exposed grid for Hospitals, Shopping malls, Commercial establishments and office complexes. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 87%, Thermal Conductivity k = 0.052 - 0.057 w/m K, NRC -0.7,Colour White, Fire Performance UK A2 S1, dO, with Anti Microbial coating on the face of the tile, suitable for zone 4 area according to NF S 90-35:2003 with cleanroom class of ISO 5 (Class 100), Decontamination Class of CP1Oand Bacteriological Cleanliness Class B1 for specific strains and reduction in colony size. Washability properties of 500 wash cycles as per ASTM D-4828 and suitable for Green Building application with Recycled content of 37%. The tile shall be laid on 24mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm and a load carrying capacity of 15 kg/m2 & pull out strength of minimum 100 kg The T Sections should have a Galvanizing of 90 grams per m2 and need to be installed with suspension system of approved make.- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code20 - Providing and fixing in position fully panelled Honne wood shutters for doors with stiles and rails of 40mm. thick with bottom and lock rails 180mm wide top rail and stiles 100mm wide as per drawing and panels of 25mm thick including cost of materials, labour, usage charges complete as per specifications. ( excluding cost of fixtures )- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work

code21 - Design parameter- Supply installation and commissioning of the water treatment plant capable to treat the water and make it potable at the flow rate of . LPH with suspended solids level less than 2000ppm, and PH value and biological impurities beyond permissible limits of potable water parameters. NOTE: Refer the ANNEXURE : A . for separate components of water treatment plant, Detailed Dimension and Rates as per Flow Rate mentioned in annexure For WTP 20000 LPH- Charges with all lead and lift including other incedental charges wherever necessary for successful completion of work and as directed by the Engineer in Charge of Work